![Ariens ST28DLET PRO TRACK [28/38] Traction drive belt replacement](/img/pdf.png)
Ariens ST28DLET PRO TRACK [28/38] Traction drive belt replacement
![Ariens ST28DLET PRO HYDRO TRACK [28/38] Traction drive belt replacement](/views2/1509893/page28/bg1c.png)
EN - 28
7. Remove attachment drive belts from
engine sheave (it may be necessary to
turn engine sheave using recoil starter
handle).
IMPORTANT: To avoid bending bottom cover
when tipping unit apart, support handlebars
firmly or tip unit up on housing and remove
bottom cover by removing six cap screws
before separating unit.
8. Support Sno-Thro frame and housing.
9. Remove hex bolts securing housing to
frame (one on each side). Tip housing
and frame apart on pivot pins
(Figure 30).
10. Remove attachment drive belts from
attachment pulley (hold brake away from
belts).
Install new attachment drive belts
1. Place new attachment belts onto
attachment pulley.
NOTE: Holding down the attachment clutch
lever will make it easier to reconnect the
housing and frame.
2. Tip housing and frame back together
and secure with hex bolts.
3. Place belts onto engine sheave.
4. Reposition and secure belt fingers.
IMPORTANT: With clutch lever engaged, belt
finger on the side opposite the belt idler
should be less than 1/8 in. (3 mm) from belts,
but not touching the belts. Adjust belt finger
as necessary.
5. Check adjustment. See Check Belt
Finger Clearance on page 27.
6. Reconnect chute crank and secure with
spring clip. Reconnect chute lock cable
and deflector cable.
7. Replace chute gear cover.
8. Replace belt cover and tighten
hardware.
TRACTION DRIVE BELT
REPLACEMENT
(Figure 31)
NOTE: Replacement will be easier with
housing and frame tipped apart and bottom
cover off.
1. Remove attachment drive belts (see
Remove old attachment drive belts on
page 27).
2. Remove hairpin attaching traction cable
to the idler arm, and disconnect the
cable. (Figure 31).
3. Pull idler away from traction drive belt
and remove belt from idler pulley, engine
sheave and pulley (it may be necessary
to turn engine pulley using recoil
handle).
4. Install new traction drive belt onto pulley,
stationary idler pulley and engine
sheaves.
5. Replace attachment drive belts (see
Install new attachment drive belts on
page 28).
CAUTION: Always support Sno-
Thro frame and blower housing
when loosening the cap screws
holding them together. Never
loosen cap screws while unit is in
service position.
Figure 30
1. Pivot Pin
2. Housing Cap Screws
3. Belt Cover
2
3
1
WARNING: AUGER / IMPELLER
MUST STOP within 5 seconds
when attachment clutch lever is
released or unit damage or serious
injury may result.
Figure 31
1. Traction Drive Belt
2. Engine Sheave
3. Belt Finger
4. Attachment Belts Idler
5. Attachment Pulley
6. Attachment Idler Adjustment Nut
7. Traction Belt Idler
1
2
3
4
7
5
6
Содержание
- Hydro pro sno thr 1
- Manuel du propriétaire utilisateur 1
- Models 1
- Owner operator manual 1
- Engine manual 2
- Introduction 2
- Manuals 2
- Model and serial numbers 2
- Product registration 2
- Table of contents 2
- Delivery 3
- Disclaimer 3
- Unauthorized replacement parts 3
- Attention 4
- Become alert 4
- Notations 4
- Obey the message 4
- Personal safety is involved 4
- Practices and laws 4
- Required operator training 4
- Safety 4
- Safety alerts 4
- Safety decals and locations 4
- Danger 5
- Emission control system 6
- Safety rules 6
- Assembly 8
- Install discharge chute chute control and chute rod 8
- Package contents 8
- Tools required 8
- Unfold handlebar 8
- Check auger gearcase oil 10
- Check engine crankcase oil 10
- Check function of all controls 10
- Check function of dual handle interlock 10
- Check tire pressure 926053 054 055 10
- Check track tension 926056 10
- Fill fuel tank 10
- Remote deflector control 10
- Run in attachment belt 10
- Setting neutral position 10
- Controls and features 11
- Attachment clutch right hand lever 13
- Controls and features 13
- Dual handle interlock 13
- Ignition switch 120vac start 13
- Operation 13
- Primer bulb 13
- Speed selector 13
- Traction drive clutch left hand lever 13
- Choke control knob 14
- Choke run 14
- Discharge chute 14
- Electric starter 14
- Quick turn chute control 14
- Recoil starter handle 14
- Remote deflector control 14
- Snow clean out tool 14
- Throttle 14
- Differential lock 926056 15
- Moving the unit with the engine off 15
- Drift cutters 16
- Heated handles 16
- Scraper blade 16
- Skid shoes 16
- Track angle 926056 16
- Add fuel stabilizer to extend fuel storage life 17
- Add fuel to fuel tank 17
- Filling fuel tank 17
- Gasoline 17
- Check axle lock 926056 18
- Check dual handle interlock 18
- Check engine fuel crankcase oil 18
- Check function of clutches 18
- Check skid shoes 18
- Frozen impeller 18
- Fuel shut off valve 18
- Manual start 18
- Pre start 18
- Starting and shut off 18
- To stop in an emergency 18
- Electric start 120v 19
- Shut off 19
- Snow removal 19
- Tips for operation 19
- Transport 19
- Traveling 19
- Check dual handle interlock 20
- Check fasteners 20
- Maintenance 20
- Maintenance schedule 20
- Service position 20
- 054 05 21
- Change engine oil 21
- Check auger gearcase 21
- Check clutch cable adjustment 21
- Check clutch operation 21
- Check engine oil 21
- Check tire pressure 21
- Clean engine 21
- Auger shaft 22
- General lubrication 22
- For replacement 23
- Scraper blade 23
- Service and adjustments 23
- Shear bolts 23
- Skid shoes 23
- Handlebar height 24
- Remote deflector control 24
- Attachment clutch brake adjustment 25
- Discharge chute control 25
- Remove attachment cable slack 25
- Speed selector adjustment 25
- Check attachment idler arm roller clearance 26
- Attachment drive belts replacement 27
- Check attachment brake 27
- Check belt finger clearance 27
- Remove old attachment drive belts 27
- Traction drive clutch adjustment 27
- Install new attachment drive belts 28
- Traction drive belt replacement 28
- Height adjuster cable adjustment 926056 29
- Track tension adjustment 926056 29
- Add fuel stabilizer 30
- Fuel system 30
- Long term 30
- Short term 30
- Storage 30
- Accessories 31
- Engine problems 31
- Engine stops 31
- Engine will not crank start 31
- Problem probable cause correction 31
- Service parts 31
- Troubleshooting 31
- Does not operate in forward reverse 32
- Problem probable cause correction 32
- Troubleshooting 32
- Unit throws snow poorly or does not throw snow 32
- Automatic traction control 33
- Height in cm 33
- Length in cm 33
- Specifications 33
- Traction control with axle mounted lockout 33
- Weight lbs kg 33
- Width in cm 33
- X 4 8 41 x 12 20 16 x 6 8 41 x 16 20 5 13 7 track 33
- And chore performing equipment limited warranty 34
- Sno te 34
- Sno thr 34
- Sno thro sno tek and chore performing equipment limited warranty 34
- Special extensions 34
- Customer responsibilities 35
- Exceptions and limitations 35
- To find an authorized service representative 35
- Australian consumer law 36
- Disclaimer 36
- Disclaimer of further warranty 36
- Exclusions items not covered by this warranty 36
- Limitation of remedy and damages 36
- Special exclusions on utility vehicles 36
- California and epa united states environmental protection agency evaporative emission control warranty statement 37
Похожие устройства
- Ariens ST28LET TRACK Руководство пользователя
- Ariens ST30DLE DELUXE Руководство пользователя
- Ariens SNO-TEK 28E Руководство пользователя
- Ariens POWER BRUSH 28 Руководство пользователя
- Yanmar YDP 40 STN-E Руководство пользователя
- Sdmo ST 2.36 H Руководство пользователя
- Sdmo TR 2.36 H Руководство пользователя
- Sdmo ST 3.60 H Руководство пользователя
- Sdmo TR 3.60 H Руководство пользователя
- Sdmo HP 2.26 H Руководство пользователя
- Sdmo XC 2.34 H Руководство пользователя
- Honda WMP 20 Руководство пользователя
- Gardena 3500/4E Classic Руководство пользователя
- Whirlpool AWT 2240 Таблица программ
- Whirlpool AWT 2240 Инструкция по эксплуатации
- Kawasaki ZXR 400 Сервисный мануал
- Kawasaki ZXR 400 Инструкция по эксплуатации
- Gardena Classic 4000/4i EP Инструкция по эксплуатации
- Al-Ko HW 600 Eco Инструкция по эксплуатации
- Karcher BP 4 Deep Well Инструкция по эксплуатации