Gigabyte H370 HD3 (rev. 1.0) [42/48] 2 installing an intel optane memory

3-2 InstallinganIntel

Optane

™

Memory

SystemRequirements

1. Intel

Optane

™

memory

2. The Optane

™

memory must have at least 16 GB capacity, and it must have equal or smaller capacity than

the hard drive/SSD to be accelerated.

3. The Optane

™

memorycannotbeusedtoaccelerateanexistingRAIDarray;theacceleratedharddrive/SSD

cannotbeincludedinaRAIDarray.

4. The hard drive/SSD to be accelerated must be a SATA hard drive or M.2 SATA SSD and must have Windows 10

64-bit (or later version) installed on it. (Must be formatted for GPT partition.)

5. The motherboard driver disk

InstallationGuidelines

A-1:InstallationinAHCImode

IftheSATAcontrollerhasbeenconguredinAHCImode,pleasefollowthestepsbelow:

1. After entering the operating system, insert the motherboard driver disk into your optical drive. On the Xpress

Install screen, select Intel(R)Optane(TM)MemorySystemAcceleration

(Note)

to install. Follow the on-screen

instructions to continue. The system will auto-restart.

2. After re-entering the operating system, the dialog box as shown above will appear. Click Yes to continue the

installation and then restart the system.

3. LaunchtheIntel(R)OptaneMemoryapplicationfromtheStartmenu.AmessagewhichsaysIntel

Optane

™

Memory is disabled will appear on the main screen. Click Enable to activate the Intel

Optane

™

Memory

and restart the system again.

4. LaunchtheIntel(R)OptaneMemoryapplicationfromtheStartmenuandmakesuretheIntel

Optane

™

Memoryhasbeenenabled.(TheSATAcontrollermodeischangedtoIntelRSTPremiumWithIntelOptane

System Acceleration from AHCI mode. DO NOT change your SATA controller mode back to AHCI. Doing so

will prevent Intel

Optane

™

memory from functioning properly.)

(Note) If the system already has Intel

RapidStorageTechnologyutilityinstalled,youhavetoremoveitrst

beforeinstallingtheIntel(R)Optane(TM)MemorySystemAccelerationapplication.

InstallingtheSATARAID/AHCIDriverandOperatingSystem

With the correct BIOS settings, you are ready to install the operating system.

InstallingtheOperatingSystem

AssomeoperatingsystemsalreadyincludeSATARAID/AHCIdriver,youdonotneedtoinstallseparateRAID/

AHCI driver during the Windows installation process. After the operating system is installed, we recommend

thatyouinstallallrequireddriversfromthemotherboarddriverdiskusing"XpressInstall"toensuresystem

performance and compatibility. If the operating system to be installed requires that you provide additional SATA

RAID/AHCIdriverduringtheOSinstallationprocess,pleaserefertothestepsbelow:

1. Copy the IRST folder under \Boot in the driver disk to your USB thumb drive.

2. Boot from the Windows setup disk and perform standard OS installation steps. When the screen requesting

you to load the driver appears, select Browse.

3. ThenbrowsetotheUSBashdriveandselectthelocationofthedriver.Thelocationofthedriverisas

follows:\IRST\f6py-x64

4. When a screen as shown, select IntelChipsetSATARAIDController and click Next to load the driver and

continue the OS installation.

- 42 -

Gigabyte H370 HD3 (rev. 1.0) [42/48] 2 installing an intel optane memory

Содержание

Похожие устройства