![Icom IC-M710RT [16/32] User channel programming](/img/pdf.png)
Icom IC-M710RT [16/32] User channel programming
![Icom IC-M710RT [16/32] User channel programming](/views2/1074674/page16/bg10.png)
12
5
USER CHANNEL PROGRAMMING
■ Programming a frequency
The IC-M710RT has up to 160 user-programmable
channels each with channel name capability of up to 7
alphanumeric characters.
☞ NOTE: ITU simplex channels can be programmed
as well as user channels. However, transmit fre-
quencies cannot be programmed as it is not neces-
sary.
D Receive frequency
➀
Select the desired channel to be programmed.
• Channels 1 to 160 (maximum) are programmable.
➁ Push [CE] to select frequency selection mode.
•“s” and frequency appear on the display.
➂ Enter the desired frequency via the keypad—5 or
6 digits.
• Or rotate the [CHANNEL] selector to change the fre-
quency.
➃ To change the operating mode (type of emission),
push [MODE] one or more times.
➄ Push and hold [RX] for 1 sec. to program the user
channel.
D Transmit frequency
(Not applicable for General versions)
➀ Select the desired user channel to be programmed.
➁ Push [TX].
•“$” flashes.
➂ Push [CE] to select frequency selection mode.
•“s” and frequency appear on the display.
➃ Enter the desired frequency via the keypad with 5
or 6 digits.
• The [CHANNEL] selector cannot be used.
➄ Push and hold [TX] for 1 sec. to program.
➅ Push [TX] to stop “$” from flashing.
D Channel names
➀
Select the desired user channel to be programmed.
➁ Push [CH/FREQ] to select channel indication.
➂ Push [FUNC] then [CE].
• The channel name (alphanumeric) readout flashes.
➃ Rotate the [GROUP] selector for cursor position
and the [CHANNEL] selector for name content.
• To return to the previous message, push [CE].
➄ Push and hold [RX] to program the name.
• Flashing stops.
DUP
TX
RX
DSC
F
AGC
ALM
DUP
TX
RX
DSC
F
AGC
ALM
DUP
TX
RX
DSC
F
AGC
ALM
Push [CE]
Frequency and “≈” appear.
Set frequency
Use keypad or channel selector.
Push and hold [RX]
Programming is completed.
DUP
TX
RX
DSC
F
AGC
ALM
DUP
TX
RX
DSC
F
AGC
ALM
DUP
TX
RX
DSC
F
AGC
ALM
Push [TX]
“$” flashes.
Push [CE]
Push and hold [TX]
after entering a
frqeuency
DUP
TX
RX
DSC
F
AGC
ALM
DUP
TX
RX
DSC
F
AGC
ALM
DUP
TX
RX
DSC
F
AGC
ALM
Push [FUNC]
then [CE]
“$” flashes.
Rotate [GROUP]
and [CHANNEL]
to select cursor and
character
Push [RX]
IC-M710RT.qxd 02.1.9 9:03 Page 12
Содержание
- Im710rt 1
- Explicit definitions 2
- Important 2
- Precautions 2
- R warning 2
- In case of emergency for maritime operation 3
- Using 2182 khz with voice 3
- Using digital selective calling 3
- Versions 3
- When a potential problem exists 3
- When immediate help is needed 3
- Table of contents 4
- Call procedures 5
- Operating rules and guidelines 5
- Priorities 5
- Privacy 5
- Radio licenses 5
- I front panel controller 6
- Panel description 6
- D hm 120 microphone keys 8
- I main unit controller detached 8
- Dsc f scan sql n b agc agc 9
- Dup simp 9
- I display 9
- I selecting a channel 10
- Selecting a channel frequency 10
- D using scan functions 11
- D using the keypad 11
- Caution 12
- D using the channel selector 12
- D using the keypad 12
- I selecting a frequency 12
- I basic voice receive and transmit 13
- I functions for transmit 13
- Receive and transmit 13
- D agc off function 14
- D clarity control 14
- D noise blanker 14
- D rf gain setting 14
- D squelch function 14
- I functions for receive 14
- Cross channel operation example 15
- Cw key connection 15
- Fsk terminal unit connection 15
- I cross channel operation 15
- I cw operation 15
- I fsk operation 15
- I programming a frequency 16
- User channel programming 16
- I set mode contents 17
- I set mode operation 17
- Set mode 17
- 4 scan type selection scan type only this item selects one of the following scan functions 18
- 5 scan speed this item adjusts the scan speed rate at which chan nels are searched the scan speed can be set from 1 to 10 with 1 being the fastest and 10 being the slowest 18
- 6 channel name and frequency the lower half of the display can be set to display a programmable channel name or a receive frequency according to operator needs 18
- 7 cw fsk narrow filter this item selects the passband width for a1a cw fsk or j2b mode 18
- 8 fsk shift frequency several shift frequencies the difference between the mark and space frequency are used for fsk opera tion this item allows you to select a shift frequency for almost any fsk system 18
- Channel resume scan scan operates over the fre quency range optional 18
- Channel resume scan scan pauses when squelch opens then resumes after 10 sec 18
- Channel scan and channel resume scan search 5 channels around a user selected channel or search all itu channels in the band when an itu channel is selected 18
- Channel scan scan is canceled when transmitting default 18
- Default 4 18
- Fastest scan speed 18
- Hz 6 db gmdss 18
- Note when on is selected without optional fil ter installation the marine and general versions do not function in these modes the gmdss ver sions can use on as standard 18
- Passband 2 khz 6 db default 18
- Passband 500 hz 6 db 18
- Programmed scan optional searches signals within the frequency range and activates slowly while squelch is open and fast while squelch is closed 18
- Set mode 18
- Shift frequency 170 hz default 18
- Shift frequency 425 hz 18
- Shift frequency 850 hz 18
- Slowest scan speed 18
- Connections and installation 20
- I attaching 1 remote controller 20
- I supplied accessories 20
- Connections and installation 21
- D intercom operation 21
- D set id number 21
- I attaching 2 remote controllers 21
- Push and hold the ptt switch on the microphone and speak into the microphone at a normal voice level 21
- Push func and then push speaker to turn the intercom function on 21
- Push func to end intercom operation 21
- Push power turn the power off 21
- Rotate the channel selector to select the desired unit id number if desired 21
- The id numbers for each remote controller must be set properly for the intercom function to operate see right 21
- The intercom function allows you to communicate be tween two remote controllers 21
- While pushing func push power 21
- Caution 22
- I attaching 2 remote controllers and a pc 22
- I notes for remote control 22
- Caution 23
- I connections on rear panel 23
- Acc 1 pin pin name description specifications 24
- Acc 2 acc pin pin name description specifications 24
- Connections and installation 24
- I connector information 24
- Microphone pin pin name description specifications 24
- Tuner pin pin name description specifications 24
- Connections and installation 25
- Dc 13 v pin pin name description specifications 25
- Dsc pin pin name description specifications 25
- Mod af pin pin name description specifications 25
- Remote pin pin name description specifications 25
- I ground connection 26
- I power source 26
- At 130 e 27
- Coaxial cable 27
- Connections and installation 27
- Control cable sold separately an optional opc 566 is available 27
- D at 130 at 130e automatic antenna tuner 27
- D mn 100 mn 100l antenna matchers 27
- D non icom tuner 27
- I antenna 27
- Ic m710rt 27
- Most stations operate with a whip or long wire insu lated backstay antenna however these antennas cannot be connected directly to the transceiver since their impedance may not be matched with the trans ceiver antenna connector 27
- Some non icom tuners may be used with the ic m please consult your dealer or marina if you wish to connect one the following internal settings may be required for connection 27
- To antenna element 27
- With a 50 ω matched antenna all marine bands can not be used the following antenna matcher or an tenna tuner may be helpful for antenna installation 27
- Check the installation angle the display may not be easy to read at some angles 28
- Connections and installation 28
- D mounting location 28
- D mounting the controller main body 28
- D transceiver dimensions 28
- I mounting 28
- Select a location that provides easy access to the front panel for navigation safety has good ventilation and is not subject to sea spray the controller should be at 90 degrees to your line of sight when operating it 28
- U caution keep the transceiver and microphone at least 1 meter away from your vessel s magnetic nav igation compass 28
- D installing an optional filter and alarm unit 29
- D opening the case 29
- I fuse replacement 29
- I installing internal options 29
- Possible cause 30
- Power transmit display receive 30
- Problem 30
- Solution 30
- Troubleshooting 30
- What appears to be equipment malfunction may not be damaging or difficult to solve check the following chart before making any adjustments or sending the trans ceiver to an icom service center 30
- General 31
- I options 31
- I specifications 31
- Options and specifications 31
- Receiver 31
- Transmitter 31
- 1 32 kamiminami hirano ku osaka 547 0003 japan 32
- A 5504h 1ex q printed in japan 1998 icom inc 32
- Count on us 32
- Ic m710rt qxd 02 9 03 page 28 32
Похожие устройства
- Asko OS8440 EU STEAM OVEN Инструкция по эксплуатации
- Bosch KGV39XL20R Инструкция по эксплуатации
- Icom MR-1000R2 Инструкция по эксплуатации
- Asko OT8620 EU ELECTRIC OVEN Инструкция по эксплуатации
- Hotpoint-Ariston HBU 1201.4 X NF H O3 Инструкция по эксплуатации
- Icom MR-1000T2 Инструкция по эксплуатации
- Asko C9505 A42002006 RU WHITE FS 50 Инструкция по эксплуатации
- Bosch KGE36AW30R Инструкция по эксплуатации
- Icom IC-PCR100 Инструкция по эксплуатации
- Asko C9510 A42002003 RU WHITE FS 50 Инструкция по эксплуатации
- Siemens KG39EAW20R Инструкция по эксплуатации
- Icom IC-PCR1000 Инструкция по эксплуатации
- Asko C9535 A42002022 RU WHITE FS 50 Инструкция по эксплуатации
- Siemens KG36EAL20R Инструкция по эксплуатации
- Icom IC-R1500 Инструкция по эксплуатации
- Bosch KGE36AI20R Инструкция по эксплуатации
- Asko C9540 A42002017 RU WHITE FS 50 Инструкция по эксплуатации
- Icom IC-PCR1500 Инструкция по эксплуатации
- Bosch KGE39AW30R Инструкция по эксплуатации
- Asko C9545 A42002025 RU WHITE FS 50 Инструкция по эксплуатации
Скачать
Случайные обсуждения