![Nissan Note — руководство по быстрой зарядке аккумуляторов и настройкам тока [13/60]](/img/pdf.png)
Nissan Note — руководство по быстрой зарядке аккумуляторов и настройкам тока [13/60]
![Nissan Note [13/60] Do not use quick charge method on a battery whose specific gravity is less than 1 00](/views2/1789832/page13/bgd.png)
BATTERY
SC-13
C
D
E
F
G
H
I
J
L
M
A
B
SC
Fig. 6 Initial Charging Current Setting and Charging Time (Quick Charge)
● Check battery type and determine the specified current using the table shown above.
● After starting charging, adjustment of charging current is not necessary.
CAUTION:
● Do not use quick charge method on a battery whose specific gravity is less than 1.100.
● Set initial charging current to value specified in Fig. 6. If charger is not capable of producing spec-
ified current value, set its charging current as close to that value as possible.
● Keep battery away from open flame while it is being charged.
● When connecting charger, connect leads first, then turn on charger. Do not turn on charger first,
as this may cause a spark.
● Be careful of a rise in battery temperature because a large current flow is required during quick-
charge operation.
If battery temperature rises above 60°C(140°F), stop charging. Always charge battery when its
temperature is below 60°C(140°F).
BATTERY TYPE
28B19R(L)
34B19R(L)
46B24R(L)
55B24R(L)
50D23R(L)
55D23R(L)
65D26R(L)
80D26R(L)
025 [YUASA type code]
027 [YUASA type code]
063 [YUASA type code]
LB1 FCM 047 620 [EXIDE type code]
LB2 FCM 050 622 [EXIDE type code]
LB2 FCM 055 622 [EXIDE type code]
067 [YUASA type code]
096 [YUASA type code]
065 [YUASA type code]
075 [YUASA type code]
096L [YUASA type code]
010S [YUASA type code]
75D31R(L)
95D31R(L)
115D31R(L)
110D26R(L)
95E41R(L)
130E41R(L)
CURRENT [A]
10 (A) 15 (A) 20 (A)
21(A)
23(A)
24(A)
25 (A) 30 (A)
40 (A)
CONVERTED SPECIFIC GRAVITY
1.100 - 1.130
2.5 hours
1.130 - 1.160
2.0 hours
1.160 - 1.190
1.5 hours
1.190 - 1.220
1.0 hours
Above 1.220
0.75 hours (45 min.)
Содержание
- Contents p.1
- Starting charging system p.1
- Sectio p.1
- K electrical p.1
- Precautions for supplemental restraint system srs air bag and seat belt pre tensioner p.3
- Precautions p.3
- Special service tools p.4
- Preparation p.4
- Methods of preventing over discharge p.5
- How to handle battery p.5
- Checking electrolyte level p.5
- Battery p.5
- Sulphation p.6
- Specific gravity check p.6
- Battery p.6
- Battery test and charging chart p.7
- Battery p.7
- Chart i p.7
- Fig 1 discharging current load tester p.8
- Check battery type and determine the specified current using the following table p.8
- Chart ii p.8
- Battery p.8
- Battery p.9
- A slow charge p.9
- Set charging current to value specified in fig 2 if charger is not capable of producing specified current value set its charging current as close to that value as possible p.10
- Keep battery away from open flame while it is being charged p.10
- If battery temperature rises above 60 c 140 f stop charging always charge battery when its temperature is below 60 c 140 f p.10
- Fig 3 additional charge slow charge p.10
- Fig 2 initial charging current setting slow charge p.10
- Check battery type and determine the specified current using the table shown above p.10
- Caution p.10
- Battery p.10
- After starting charging adjustment of charging current is not necessary p.10
- When connecting charger connect leads first then turn on charger do not turn on charger first as this may cause a spark p.10
- Fig 4 initial charging current setting standard charge p.11
- Battery p.11
- B standard charge p.11
- Fig 5 additional charge standard charge p.12
- C quick charge p.12
- Battery p.12
- Set initial charging current to value specified in fig 6 if charger is not capable of producing spec ified current value set its charging current as close to that value as possible p.13
- Keep battery away from open flame while it is being charged p.13
- Fig 6 initial charging current setting and charging time quick charge p.13
- Do not use quick charge method on a battery whose specific gravity is less than 1 00 p.13
- Check battery type and determine the specified current using the table shown above p.13
- Caution p.13
- Be careful of a rise in battery temperature because a large current flow is required during quick charge operation if battery temperature rises above 60 c 140 f stop charging always charge battery when its temperature is below 60 c 140 f p.13
- Battery p.13
- After starting charging adjustment of charging current is not necessary p.13
- When connecting charger connect leads first then turn on charger do not turn on charger first as this may cause a spark p.13
- Removal and installation p.14
- Removal p.14
- Installation p.14
- Battery p.14
- System description k9k engine models p.15
- System description hr engine models p.15
- System description cr engine models p.15
- Charging system p.15
- Wiring diagram charge hr engine models p.17
- Charging system p.17
- Charging system p.19
- Inspection flow by charge warning lamp p.20
- Diagnosis procedure p.20
- Diagnosis chart by symptom p.20
- Charging system p.20
- Trouble diagnoses cr engine models p.20
- Pre diagnosis inspection p.20
- Inspection procedure p.21
- Charging system p.21
- Charge warning lamp line inspection p.21
- Inspection of insufficient alternator power generation p.22
- Charging system p.22
- Inspection of excessive alternator power generation p.23
- Dark current inspection p.23
- Charging system p.23
- Operation procedure of current measurement probe for consult ii p.24
- Charging system p.24
- Inspection flow by charge warning lamp p.25
- Diagnosis procedure p.25
- Diagnosis chart by symptom p.25
- Charging system p.25
- Trouble diagnoses hr engine models p.25
- Pre diagnosis inspection p.25
- Inspection procedure p.26
- Charging system p.26
- Charge warning lamp line inspection p.26
- Voltage detection line and charge warning lamp inspection p.27
- Inspection procedure p.27
- Charging system p.27
- Inspection of insufficient alternator power generation p.28
- Charging system p.28
- Inspection of excessive alternator power generation p.29
- Charging system p.29
- Dark current inspection p.30
- Charging system p.30
- Operation procedure of current measurement probe for consult ii p.31
- Charging system p.31
- Trouble diagnoses k9k engine models p.32
- Pre diagnosis inspection p.32
- Inspection flow by charge warning lamp p.32
- Diagnosis procedure p.32
- Diagnosis chart by symptom p.32
- Charging system p.32
- Inspection procedure p.33
- Charging system p.33
- Charge warning lamp line inspection p.33
- Voltage detection line and charge warning lamp inspection p.34
- Inspection procedure p.34
- Charging system p.34
- Charging system p.35
- Inspection of insufficient alternator power generation p.36
- Inspection of excessive alternator power generation p.36
- Charging system p.36
- Dark current inspection p.37
- Charging system p.37
- Operation procedure of current measurement probe for consult ii p.38
- Charging system p.38
- Removal and installation cr engine models p.39
- Removal p.39
- Charging system p.39
- Removal and installation hr engine models p.40
- Removal p.40
- Installation p.40
- Charging system p.40
- Installation p.41
- Charging system p.41
- Installation p.42
- Disassembly p.42
- Charging system p.42
- Removal and installation k9k engine models p.42
- Removal p.42
- Rear cover p.42
- Stator check p.43
- Rotor check p.43
- Rear bearing p.43
- Inspection p.43
- Charging system p.43
- Brush check p.43
- Ring fitting in rear bearing p.44
- Rear cover installation p.44
- Charging system p.44
- Assembly p.44
- Starting system p.45
- M t models p.45
- A t models p.45
- System description p.45
- Starting system p.47
- Starting system p.49
- Starting system p.51
- Removal and installation hr engine models p.51
- Removal and installation cr engine models p.51
- Removal p.51
- Installation p.51
- Starting system p.52
- Removal and installation k9k engine models p.52
- Removal p.52
- Installation p.52
- Disassembly and assembly p.52
- Through bolt m0t84585 p.53
- Starting system p.53
- 4 7 n m 0 5 0 2 kg m 39 62 in lb p.53
- Starting system p.54
- Starting system p.55
- Pinion clutch check p.55
- Magnetic switch check p.55
- Inspection p.55
- Brush check brush p.55
- Starting system p.56
- Brush spring check p.56
- Brush holder p.56
- Yoke check p.57
- Starting system p.57
- Armature check p.57
- Starting system p.58
- Pinion protrusion length adjustment clearance p.58
- Assembly p.58
- Not in the specified value adjust by adjusting plate p.59
- Starting system p.59
- Starter p.60
- Service data and specifications sds p.60
- Battery p.60
- Alternator p.60
Похожие устройства
-
Nissan Murano z50Руководство пользователя -
Nissan Murano z50Руководство пользователя ч2 -
Nissan Z50 (2002-2008)Руководство по эксплуатации -
Nissan NoteWIPER, WASHER _ HORN -
Nissan NoteROAD WHEELS _ TYRES -
Nissan NotePOWER SUPPLY, GROUND _ CIRCUIT ELEMENTS -
Nissan NoteSUPPLEMENTAL RESTRAINT SYSTEM _SRS_ -
Nissan NoteMAINTENANCE -
Nissan NoteMANUAL TRANSAXLE -
Nissan NoteSTEERING CONTROL SYSTEM -
Nissan NoteSEAT -
Nissan NotePOWER STEERING SYSTEM
Узнайте, как правильно установить начальный ток зарядки для различных типов аккумуляторов. Следуйте рекомендациям для безопасной быстрой зарядки.