![Nissan Note — установка и снятие генератора: пошаговая инструкция [40/60]](/img/pdf.png)
Nissan Note — установка и снятие генератора: пошаговая инструкция [40/60]
![Nissan Note [40/60] Removal and installation hr engine models](/views2/1789832/page40/bg28.png)
SC-40
CHARGING SYSTEM
8. Loosen alternator lower mounting bolt, and pull out from U-cut
portion on front cover.
9. Remove alternator assembly from engine.
INSTALLATION
Install in the reverse order of removal, taking care of the following point.
● Install alternator, and check tension of belt. Refer to EM-14, "Tension Adjustment" .
CAUTION:
Be sure to tighten B terminal mounting nut carefully.
Removal and Installation (HR Engine Models)
BKS000UD
REMOVAL
1. Disconnect battery ground cable.
2. Remove fender protector from RH side.
3. Remove alternator drive belt. Refer to EM-115, "
Removal and Installation" .
4. Remove idler pulley assembly. Refer to EM-116, "
Removal and Installation of Drive Belt Idler Pulley" .
5. Disconnect alternator harness connector.
● B terminal mounting nut, ground wire mounting nut, and
remove harness clips.
6. Remove A/C compressor. Refer to ATC-140, "
Removal and Installation of Compressor" (with auto A/C) or
MTC-86, "
Removal and Installation of Compressor" (with manual A/C).
MKIA0078E
B terminal nut:
: 9.32 - 10.8 N·m (0.95 - 1.1 kg-m, 82 - 95 in-lb)
Ground bolt:
:2.94-4.9N·m(0.30-0.49kg-m,26-43in-lb)
Alternator mounting bolt:
: 33.3 - 46.1 N·m (3.4 - 4.7 kg-m, 24 - 34 ft-lb)
Alternator upper bracket bolt:
: 33.3 - 46.1 N·m (3.4 - 4.7 kg-m, 24 - 34 ft-lb)
Engine mounting stay bolt:
: 40.0 - 50.0 N·m (4.1 - 5.1 kg-m, 30 - 37 ft-lb)
Idler pulley bracket bolt:
: 16.6 - 23.5 N·m (1.7 - 2.4 kg-m, 12 - 17 ft-lb)
Idler pulley nut:
: 25.5 - 33.3 N·m (2.6 - 3.3 kg-m, 19 - 24 ft-lb)
MKIB1996E
Содержание
- Contents p.1
- Starting charging system p.1
- Sectio p.1
- K electrical p.1
- Precautions for supplemental restraint system srs air bag and seat belt pre tensioner p.3
- Precautions p.3
- Special service tools p.4
- Preparation p.4
- Methods of preventing over discharge p.5
- How to handle battery p.5
- Checking electrolyte level p.5
- Battery p.5
- Sulphation p.6
- Specific gravity check p.6
- Battery p.6
- Battery test and charging chart p.7
- Battery p.7
- Chart i p.7
- Fig 1 discharging current load tester p.8
- Check battery type and determine the specified current using the following table p.8
- Chart ii p.8
- Battery p.8
- Battery p.9
- A slow charge p.9
- Set charging current to value specified in fig 2 if charger is not capable of producing specified current value set its charging current as close to that value as possible p.10
- Keep battery away from open flame while it is being charged p.10
- If battery temperature rises above 60 c 140 f stop charging always charge battery when its temperature is below 60 c 140 f p.10
- Fig 3 additional charge slow charge p.10
- Fig 2 initial charging current setting slow charge p.10
- Check battery type and determine the specified current using the table shown above p.10
- Caution p.10
- Battery p.10
- After starting charging adjustment of charging current is not necessary p.10
- When connecting charger connect leads first then turn on charger do not turn on charger first as this may cause a spark p.10
- Fig 4 initial charging current setting standard charge p.11
- Battery p.11
- B standard charge p.11
- Fig 5 additional charge standard charge p.12
- C quick charge p.12
- Battery p.12
- Set initial charging current to value specified in fig 6 if charger is not capable of producing spec ified current value set its charging current as close to that value as possible p.13
- Keep battery away from open flame while it is being charged p.13
- Fig 6 initial charging current setting and charging time quick charge p.13
- Do not use quick charge method on a battery whose specific gravity is less than 1 00 p.13
- Check battery type and determine the specified current using the table shown above p.13
- Caution p.13
- Be careful of a rise in battery temperature because a large current flow is required during quick charge operation if battery temperature rises above 60 c 140 f stop charging always charge battery when its temperature is below 60 c 140 f p.13
- Battery p.13
- After starting charging adjustment of charging current is not necessary p.13
- When connecting charger connect leads first then turn on charger do not turn on charger first as this may cause a spark p.13
- Removal and installation p.14
- Removal p.14
- Installation p.14
- Battery p.14
- System description k9k engine models p.15
- System description hr engine models p.15
- System description cr engine models p.15
- Charging system p.15
- Wiring diagram charge hr engine models p.17
- Charging system p.17
- Charging system p.19
- Inspection flow by charge warning lamp p.20
- Diagnosis procedure p.20
- Diagnosis chart by symptom p.20
- Charging system p.20
- Trouble diagnoses cr engine models p.20
- Pre diagnosis inspection p.20
- Inspection procedure p.21
- Charging system p.21
- Charge warning lamp line inspection p.21
- Inspection of insufficient alternator power generation p.22
- Charging system p.22
- Inspection of excessive alternator power generation p.23
- Dark current inspection p.23
- Charging system p.23
- Operation procedure of current measurement probe for consult ii p.24
- Charging system p.24
- Inspection flow by charge warning lamp p.25
- Diagnosis procedure p.25
- Diagnosis chart by symptom p.25
- Charging system p.25
- Trouble diagnoses hr engine models p.25
- Pre diagnosis inspection p.25
- Inspection procedure p.26
- Charging system p.26
- Charge warning lamp line inspection p.26
- Voltage detection line and charge warning lamp inspection p.27
- Inspection procedure p.27
- Charging system p.27
- Inspection of insufficient alternator power generation p.28
- Charging system p.28
- Inspection of excessive alternator power generation p.29
- Charging system p.29
- Dark current inspection p.30
- Charging system p.30
- Operation procedure of current measurement probe for consult ii p.31
- Charging system p.31
- Trouble diagnoses k9k engine models p.32
- Pre diagnosis inspection p.32
- Inspection flow by charge warning lamp p.32
- Diagnosis procedure p.32
- Diagnosis chart by symptom p.32
- Charging system p.32
- Inspection procedure p.33
- Charging system p.33
- Charge warning lamp line inspection p.33
- Voltage detection line and charge warning lamp inspection p.34
- Inspection procedure p.34
- Charging system p.34
- Charging system p.35
- Inspection of insufficient alternator power generation p.36
- Inspection of excessive alternator power generation p.36
- Charging system p.36
- Dark current inspection p.37
- Charging system p.37
- Operation procedure of current measurement probe for consult ii p.38
- Charging system p.38
- Removal and installation cr engine models p.39
- Removal p.39
- Charging system p.39
- Removal and installation hr engine models p.40
- Removal p.40
- Installation p.40
- Charging system p.40
- Installation p.41
- Charging system p.41
- Installation p.42
- Disassembly p.42
- Charging system p.42
- Removal and installation k9k engine models p.42
- Removal p.42
- Rear cover p.42
- Stator check p.43
- Rotor check p.43
- Rear bearing p.43
- Inspection p.43
- Charging system p.43
- Brush check p.43
- Ring fitting in rear bearing p.44
- Rear cover installation p.44
- Charging system p.44
- Assembly p.44
- Starting system p.45
- M t models p.45
- A t models p.45
- System description p.45
- Starting system p.47
- Starting system p.49
- Starting system p.51
- Removal and installation hr engine models p.51
- Removal and installation cr engine models p.51
- Removal p.51
- Installation p.51
- Starting system p.52
- Removal and installation k9k engine models p.52
- Removal p.52
- Installation p.52
- Disassembly and assembly p.52
- Through bolt m0t84585 p.53
- Starting system p.53
- 4 7 n m 0 5 0 2 kg m 39 62 in lb p.53
- Starting system p.54
- Starting system p.55
- Pinion clutch check p.55
- Magnetic switch check p.55
- Inspection p.55
- Brush check brush p.55
- Starting system p.56
- Brush spring check p.56
- Brush holder p.56
- Yoke check p.57
- Starting system p.57
- Armature check p.57
- Starting system p.58
- Pinion protrusion length adjustment clearance p.58
- Assembly p.58
- Not in the specified value adjust by adjusting plate p.59
- Starting system p.59
- Starter p.60
- Service data and specifications sds p.60
- Battery p.60
- Alternator p.60
Похожие устройства
-
Nissan Murano z50Руководство пользователя -
Nissan Murano z50Руководство пользователя ч2 -
Nissan Z50 (2002-2008)Руководство по эксплуатации -
Nissan NoteWIPER, WASHER _ HORN -
Nissan NoteROAD WHEELS _ TYRES -
Nissan NotePOWER SUPPLY, GROUND _ CIRCUIT ELEMENTS -
Nissan NoteSUPPLEMENTAL RESTRAINT SYSTEM _SRS_ -
Nissan NoteMAINTENANCE -
Nissan NoteMANUAL TRANSAXLE -
Nissan NoteSTEERING CONTROL SYSTEM -
Nissan NoteSEAT -
Nissan NotePOWER STEERING SYSTEM
Подробная инструкция по снятию и установке генератора. Узнайте, как правильно выполнить все этапы, включая проверку натяжения ремня и затяжку крепежей.