Nissan Note [42/60] Charging system

Содержание

• Contents p.1
• Starting charging system p.1
• Sectio p.1
• K electrical p.1
• Precautions for supplemental restraint system srs air bag and seat belt pre tensioner p.3
• Precautions p.3
• Special service tools p.4
• Preparation p.4
• Methods of preventing over discharge p.5
• How to handle battery p.5
• Checking electrolyte level p.5
• Battery p.5
• Sulphation p.6
• Specific gravity check p.6
• Battery p.6
• Battery test and charging chart p.7
• Battery p.7
• Chart i p.7
• Fig 1 discharging current load tester p.8
• Check battery type and determine the specified current using the following table p.8
• Chart ii p.8
• Battery p.8
• Battery p.9
• A slow charge p.9
• Set charging current to value specified in fig 2 if charger is not capable of producing specified current value set its charging current as close to that value as possible p.10
• Keep battery away from open flame while it is being charged p.10
• If battery temperature rises above 60 c 140 f stop charging always charge battery when its temperature is below 60 c 140 f p.10
• Fig 3 additional charge slow charge p.10
• Fig 2 initial charging current setting slow charge p.10
• Check battery type and determine the specified current using the table shown above p.10
• Caution p.10
• Battery p.10
• After starting charging adjustment of charging current is not necessary p.10
• When connecting charger connect leads first then turn on charger do not turn on charger first as this may cause a spark p.10
• Fig 4 initial charging current setting standard charge p.11
• Battery p.11
• B standard charge p.11
• Fig 5 additional charge standard charge p.12
• C quick charge p.12
• Battery p.12
• Set initial charging current to value specified in fig 6 if charger is not capable of producing spec ified current value set its charging current as close to that value as possible p.13
• Keep battery away from open flame while it is being charged p.13
• Fig 6 initial charging current setting and charging time quick charge p.13
• Do not use quick charge method on a battery whose specific gravity is less than 1 00 p.13
• Check battery type and determine the specified current using the table shown above p.13
• Caution p.13
• Be careful of a rise in battery temperature because a large current flow is required during quick charge operation if battery temperature rises above 60 c 140 f stop charging always charge battery when its temperature is below 60 c 140 f p.13
• Battery p.13
• After starting charging adjustment of charging current is not necessary p.13
• When connecting charger connect leads first then turn on charger do not turn on charger first as this may cause a spark p.13
• Removal and installation p.14
• Removal p.14
• Installation p.14
• Battery p.14
• System description k9k engine models p.15
• System description hr engine models p.15
• System description cr engine models p.15
• Charging system p.15
• Wiring diagram charge hr engine models p.17
• Charging system p.17
• Charging system p.19
• Inspection flow by charge warning lamp p.20
• Diagnosis procedure p.20
• Diagnosis chart by symptom p.20
• Charging system p.20
• Trouble diagnoses cr engine models p.20
• Pre diagnosis inspection p.20
• Inspection procedure p.21
• Charging system p.21
• Charge warning lamp line inspection p.21
• Inspection of insufficient alternator power generation p.22
• Charging system p.22
• Inspection of excessive alternator power generation p.23
• Dark current inspection p.23
• Charging system p.23
• Operation procedure of current measurement probe for consult ii p.24
• Charging system p.24
• Inspection flow by charge warning lamp p.25
• Diagnosis procedure p.25
• Diagnosis chart by symptom p.25
• Charging system p.25
• Trouble diagnoses hr engine models p.25
• Pre diagnosis inspection p.25
• Inspection procedure p.26
• Charging system p.26
• Charge warning lamp line inspection p.26
• Voltage detection line and charge warning lamp inspection p.27
• Inspection procedure p.27
• Charging system p.27
• Inspection of insufficient alternator power generation p.28
• Charging system p.28
• Inspection of excessive alternator power generation p.29
• Charging system p.29
• Dark current inspection p.30
• Charging system p.30
• Operation procedure of current measurement probe for consult ii p.31
• Charging system p.31
• Trouble diagnoses k9k engine models p.32
• Pre diagnosis inspection p.32
• Inspection flow by charge warning lamp p.32
• Diagnosis procedure p.32
• Diagnosis chart by symptom p.32
• Charging system p.32
• Inspection procedure p.33
• Charging system p.33
• Charge warning lamp line inspection p.33
• Voltage detection line and charge warning lamp inspection p.34
• Inspection procedure p.34
• Charging system p.34
• Charging system p.35
• Inspection of insufficient alternator power generation p.36
• Inspection of excessive alternator power generation p.36
• Charging system p.36
• Dark current inspection p.37
• Charging system p.37
• Operation procedure of current measurement probe for consult ii p.38
• Charging system p.38
• Removal and installation cr engine models p.39
• Removal p.39
• Charging system p.39
• Removal and installation hr engine models p.40
• Removal p.40
• Installation p.40
• Charging system p.40
• Installation p.41
• Charging system p.41
• Installation p.42
• Disassembly p.42
• Charging system p.42
• Removal and installation k9k engine models p.42
• Removal p.42
• Rear cover p.42
• Stator check p.43
• Rotor check p.43
• Rear bearing p.43
• Inspection p.43
• Charging system p.43
• Brush check p.43
• Ring fitting in rear bearing p.44
• Rear cover installation p.44
• Charging system p.44
• Assembly p.44
• Starting system p.45
• M t models p.45
• A t models p.45
• System description p.45
• Starting system p.47
• Starting system p.49
• Starting system p.51
• Removal and installation hr engine models p.51
• Removal and installation cr engine models p.51
• Removal p.51
• Installation p.51
• Starting system p.52
• Removal and installation k9k engine models p.52
• Removal p.52
• Installation p.52
• Disassembly and assembly p.52
• Through bolt m0t84585 p.53
• Starting system p.53
• 4 7 n m 0 5 0 2 kg m 39 62 in lb p.53
• Starting system p.54
• Starting system p.55
• Pinion clutch check p.55
• Magnetic switch check p.55
• Inspection p.55
• Brush check brush p.55
• Starting system p.56
• Brush spring check p.56
• Brush holder p.56
• Yoke check p.57
• Starting system p.57
• Armature check p.57
• Starting system p.58
• Pinion protrusion length adjustment clearance p.58
• Assembly p.58
• Not in the specified value adjust by adjusting plate p.59
• Starting system p.59
• Starter p.60
• Service data and specifications sds p.60
• Battery p.60
• Alternator p.60