ADJ Duo Scan RG [3/10] Operation instructions and laser safety
![ADJ Duo Scan RG [3/10] Operation instructions and laser safety](/views2/1990711/page3/bg3.png)
©American DJ® - www.americandj.com - Duo Scan RG Instruction Manual Page 5
©American DJ® - www.americandj.com - Duo Scan RG Instruction Manual Page 6
Duo Scan RG Laser Warnings and Safety
NON-INTERLOCKED HOUSING WARNING
The Duo Scan RG contains high power laser devices internally. Do
not open the laser housing, due to the potential exposure to unsafe
levels of laser radiation. The laser power levels, if the unit is opened,
can cause instant blindness, skin burns and res.
STOP AND READ ALL LASER SAFETY DATA
OPERATION INSTRUCTIONS AND LASER SAFETY
The light source emitted from this product can potentially cause eye
injury if not set up and used properly. The light source emitted from a
laser is very different from any other light sources with which you may
be aware of. Laser light is thousands of times more concentrated
than any light from any other kind of light source. This concentration
of light can cause instant eye injuries, primarily by burning the retina
(the back of your eyeball contatining cells that are sensitive to light).
Even if you cannot feel “heat” from a laser beam, it can still poten-
tially injure or blind you or your audience. Even very small amounts
of laser beam light are potentially hazardous even at long distances.
Laser eye injuries can be sustained faster than you can blink.
Do not think that because this laser splits the laser beam into hun-
dreds of beams and that the laser beam is scanned out in high
speed, that an individual laser beam is safe for eye exposure. This
laser uses dozens of milliwatts of laser power (Class 3B levels inter-
nally) before it splits into multiple beams (Class 3R levels). Many of
the individual beams are potentially hazardous to the eyes.
Do not that because the laser light is moving, it is safe. This is not
true. Nor, do the laser beams always move. Since eye injuries can
occur instantly, it is critical to prevent even the smallest possibility of
any direct eye exposure. In the laser safety regulation, it is not legal
to aim Class 3R lasers in areas which people can get exposed. This
is true even if it is aimed below people’s faces, such as on a dance
oor.
Do not operate the laser without rst reading and understanding
all safety and technical data in this manual.
Always set up and install all laser effects so that all laser light is at
least 3 meters (9.8 feet) above the oor on which people can stand.
After setting up, and before public use, test laser to ensure proper
function. Do not use if any defect is detected. Do not use if laser
emits only one or two laser beams rather than dozens/hundreds, as
this could indicate damage to the diffraction grating optic, and could
allow emission of higher laser levels above Class 3R.
Do not point lasers at people or animals. Never look into the laser
aperture or laser beams.
Do not point lasers in areas in which people can potentially get
exposed, such as uncontrolled balconies, etc.
Do not point lasers at highly reective surfaces, such as windows,
mirrors and shiny metal. Even laser reections can be hazardous.
Never point a laser at aircraft, this is a federal offense.
Never point un-terminated laser beams into the sky.
Do not expose the output optic (aperture) to cleaning chemicals.
Do not use laser if the laser appears to be emitting only one or two
beams.
Do not use the laser if the housing is damaged, the housing is open,
or if the optics appear damaged in any way.
Never open the laser housing. The high laser power levels inside of
the protective housing can start res, burn skin and will cause instant
eye injury.
Never leave this device running unattended.
The operation of a class 3R laser show is only allowed if the show
is controlled by a skilled and well- trained operator, familiar with the
data included in this manual.
The legal requirements for using laser entertainment products vary
from country to country. The user is responsible for the legal require-
ments at the location/country of use.
Always use proper lighting safety cables when hanging lights and
effects overhead.
Duo Scan RG Laser Warnings and Safety
Содержание
- Caution 1
- Customer support 1
- Introduction 1
- To purchase parts online visit http parts americandj com 1
- Unpacking 1
- User instructions 1
- Warning 1
- Danger 2
- Operation instructions and laser safety 3
- Stop and read all laser safety data 3
- Dmx 512 4
- Power supply 4
- Be sure to follow figures two and three when making your own cables do not use the ground lug on the xlr connector do not con nect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the xlr s outer casing grounding the shield could cause a short circuit and erratic behavior 5
- Conductor 5 pin xlr male in 3 pin xlr female out 5
- Data compliment signal 5
- Data true signal 5
- Duo scan rg set up 5
- Ground shield 5
- Not used 5
- Notice 5
- Pin 4 do not use 5
- Pin 5 do not use 5
- Pin xlr dmx connectors 5
- Pin xlr to 5 pin xlr conversion 5
- Some manufactures use 5 pin dmx 512 data cables for data transmission in place of 3 pin 5 pin dmx fixtures may be implemented in a 3 pin dmx line when inserting stan dard 5 pin data cables in to a 3 pin line a cable adaptor must be used these adaptors are readily available at most electric stores the chart below details a proper cable conversion 5
- Special note line termination 5
- When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behavior a terminator is a 110 120 ohm 1 4 watt resistor which is con nected between pins 2 and 3 of a male xlr connector data and data this unit is inserted in the female xlr connector of the last unit in your daisy chain to terminate the line using a cable terminator adj part number z dmx t will decrease the possibilities of erratic behavior 5
- Dmx address setting 6
- Shnd sh 0 sh 6
- Show modes 0 5 factory programs show mode can run with or without sound active mode on with sound active mode on the shows will tend to run faster 6
- System menu when confirming your setting press enter and then hold menu for at least 2 3 seconds or you can wait 1 minute for automatic setup to exit without making any adjustments press the menu button 6
- This will let you set unit as a master or slave in a master slave configuration 6
- Blackout or stand by mode 7
- Sound active mode 7
- Sound sensitivity control 7
- This function will allow you to test the pan tilt functions 7
- This function will flip the led display 180º 7
- Use this function to reset the unit 7
- With this function you can display the running time of the fixture 7
- With this function you can display the version soft ware of the unit 7
- With this function you can have the led display turn off after 10 seconds 7
- Master slave configuration 8
- Shnd is displayed and press enter 8
- Show mode 8
- Sound active mode 8
- Universal dmx control 8
- Fixture cleaning 9
- American dj europe 10
- American dj supply 10
- American dj world headquarters 10
- Auto sensing voltage 10
- Ew kerkrade 10
- Junostraat 2 10
- Model duo scan rg 10
- Netherlands 10
- Please note 10
- S eastern ave los angeles ca 90040 usa 10
- Service adjgroup eu www americandj eu 10
- Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice 10
- Tel 31 45 546 85 00 fax 31 45 546 85 99 10
- Tel 323 582 2650 fax 323 582 2610 10
- This fixture contains a automatic volt age switch which will auto sense the voltage when it is plugged into the power source 10
- Web www americandj com e mail info americandj com 10
Похожие устройства
- ADJ Double Phase LED Руководство по эксплуатации
- ADJ Comscan LED System Руководство по эксплуатации
- ADJ BOOM BOX FX3 Руководство по эксплуатации
- ADJ Atmospheric RG LED Руководство по эксплуатации
- ADJ Accu Roller 250 Руководство по эксплуатации
- ADJ Accu Fog1000 DMX Руководство по эксплуатации
- ADJ Quad Phase LED Руководство по эксплуатации
- ADJ Mystic LED Руководство по эксплуатации
- ADJ DiversaRAY Руководство по эксплуатации
- ADJ 46HP LED polish Руководство по эксплуатации
- Sennheiser RS 110-8-II Руководство по эксплуатации
- Yamaha NS-F51 Руководство по эксплуатации
- Sennheiser M2 IEBT SW Руководство по эксплуатации
- Sennheiser M2 IEBT Руководство по эксплуатации
- Sennheiser G4ME ZERO (506064) Руководство по эксплуатации
- Marshall Stockwell Руководство по эксплуатации
- Casio Privia PX-870BK Руководство по эксплуатации
- Casio Privia PX-770WE Руководство по эксплуатации
- Casio Privia PX-770BN Руководство по эксплуатации
- Sennheiser M2 IEG Руководство по эксплуатации