Zanussi W802 [5/76] Installation

Zanussi W802 [5/76] Installation
ENGLISH
5
Installation
Unpacking
All transit bolts and packing must be removed
before using the appliance.
You are advised to keep all transit devices so that
they can be refitted if the machine ever has to be
transported again.
1. Using a spanner, unscrew and remove the rear
right-hand bolt and lay the machine on its back,
taking care not to squash the hoses. This can be
avoided by placing one of the corner packing
pieces between the machine and the floor.
2. Remove the polystyrene block from the underside
of the machine and release the two plastic bags.
3. Carefully remove the right-hand bag (1) then the
left-hand bag (2) by pulling them towards the
centre of the machine.
4. Set the machine upright and remove the two
remaining bolts from the back.
5. Pull out the three plastic spacers from the holes
into which the bolts were fitted.
6. Plug the open holes with the plugs which are
supplied with the instruction booklet.
P0020
P0256
2
1
P1066
P1068
P0255
Positioning
Install the machine on a flat hard floor.
Make sure that air circulation around the machine is
not impeded by carpets, rugs etc. Check that the
machine does not touch the wall or other kitchen units.
Carefully level by screwing the adjustable feet in or
out. Never place cardboard, wood or similar
materials under the machine to compensate for any
unevenness in the floor.
Water inlet
Connect the water inlet hose supplied with the machine
to a tap with a 3/4" thread.
Do not use already employed hoses.
The other end of the inlet hose which connects to the
machine can be turned in any direction. Simply
loosen the fitting, rotate the hose and retighten the
fitting, making sure there are no water leaks.
The inlet hose must not be lengthened. If it is too
short and you do not wish to move the tap, you will
have to purchase a new, longer hose specially
designed for this type of use.
Water drainage
The end of the drain hose can be positioned in three
ways:
Hooked over the edge of a sink using the plastic
hose guide supplied with the machine. In this
case, make sure the end cannot come unhooked
when the machine is emptying.
P0021
P1088
P1051
132995520•gb.qxd 10-01-2002 17:09 Pagina 5

Содержание

Unpacking Positioning Install the machine on a flat hard floor Make sure that air circulation around the machine is not impeded by carpets rugs etc Check that the machine does not touch the wall or other kitchen units Carefully level by screwing the adjustable feet in or out Never place cardboard wood or similar materials under the machine to compensate for any unevenness in the floor j All transit bolts and packing must be removed before using the appliance You are advised to keep all transit devices so that they can be refitted if the machine ever has to be transported again 1 Using a spanner unscrew and remove the rear right hand bolt and lay the machine on its back taking care not to squash the hoses This can be avoided by placing one of the corner packing pieces between the machine and the floor Water inlet Connect the water inlet hose supplied with the machine to a tap with a 3 4 thread 2 Remove the polystyrene block from the underside of the machine and release the two plastic bags Do not use already employed hoses 3 Carefully remove the right hand bag 1 then the left hand bag 2 by pulling them towards the centre of the machine The other end of the inlet hose which connects to the machine can be turned in any direction Simply loosen the fitting rotate the hose and retighten the fitting making sure there are no water leaks 4 Set the machine upright and remove the two remaining bolts from the back The inlet hose must not be lengthened If it is too short and you do not wish to move the tap you will have to purchase a new longer hose specially designed for this type of use 5 Pull out the three plastic spacers from the holes into which the bolts were fitted 6 Plug the open holes with the plugs which are supplied with the instruction booklet Water drainage The end of the drain hose can be positioned in three ways Hooked over the edge of a sink using the plastic hose guide supplied with the machine In this case make sure the end cannot come unhooked when the machine is emptying 5 ENGLISH Installation

Скачать