Home
Главная
Incra
Позиционер
M-LS17WFNCSYS
Инструкция по эксплуатации Страница: 3

Incra M-LS17WFNCSYS [3/16] Ls positioner super system

lS Positioner “Super System”

LS Positioner Carriage

LS Positioner Base

Hi-Rise Fence Cap

Right Angle Fixture

Wonder Fence

Heavy Duty Split Fence

Incra Shop Stop

13” Telescoping Stop Extender Bar with Stop

28” Pro II Fence

Note: Also available for current Ultra owners, the Incra LS

Upgrade Package includes only the LS Positioner Carriage

and Base as shown in Fig. 1 on page 5.

INCRA LS Positioner Owner’s Manual 3

Содержание

Contents 1
Owner s manual 1
Ls positioner standard system 2
Ls positioner super system 3
Auxiliary scale slots 4
Carriage 4
Getting acquainted 4
Hairline cursor and view windows 4
Important safety instructions for using the incra ls positioner 4
Lead screw positioning element 4
Ls base 4
Safety 4
Stainless steel primary scale 4
Three position carriage clamp 4
Drill mounting holes 5
Fence mounting bracket 5
Micro adjust knob 5
Micro adjust scale dial 5
Setup mounting to your router table 5
Attach ls base to your router table 6
Pro ii fence installatio 6
Standard super 6
Attaching the pro ii fence 7
Installing pro ii extender bar and stop 7
Adjusting the fence angle 8
Attaching the wonder fence to the pro ii or ts fence 8
Mounting an auxiliary fence to your pro ii fence 8
Super system only 8
Wonder fence installation 8
Attach the fence cap braces 9
Attaching the wonder fence hi rise fence cap 9
1mm for metric version the two piece body can be micro adjusted to any position between steps and can be configured to clamp to your fence even when using wooden sub fences up to ¾ thick follow the instructions on the next page to set up and use the shop stop 10
Attach and align fence cap 10
Attach the cap extender 10
Detail 19a 10
Fig 19 10
Shop stop 10
When used in conjunction with your new pro ii fence or wonder fence the incra shop stop provides the same precise positioning capabilities that your ls positioner offers the patented incremental positioning of incra s saw toothed racks found on the shop stop and your incra fence allow perfectly repeatable stop locations at any multiple of 10
After removing the shop stop from the packaging loosen the two white nylon thumbscrews and clamp the stop to the outfeed end of your incra fence now loosen the 10 32 x 3½ phillips head screw and slide the red vertical stop arm onto the hex nut fig 22 make sure that the indexing lip on the arm wraps around the front of the stop body and that the arm is flat against the end of the body fig 23 tighten the fastener to secure the arm a short distance above your router table to provide clearance for sawdust the fastener and stop arm can be reversed for use at either end of your fence 11
Approx 1mm when turning the screw counterclockwise push the stop body toward the screw always tighten the two black thumbscrews after micro adjusting 11
Expanded clamping mode 11
Fig 22 11
Fig 23 11
Fig 24 11
Fig 25 11
Fine tuning the position of your shop stop relative to a cutter is easy and accurate just loosen the two black thumbscrews on top of the shop stop body about 11
Micro adjusting 11
Shop stop assembly 11
The two piece design of the incra shop stop permits use of a ¾ thick wooden auxiliary fence without interfering with the stop s ability to clamp to your incra fence to change the stop to expanded clamping mode loosen the two black thumbscrews and slide the stop body red off of the stop cap gold now slide the 2 rectangular nuts on the stop body into the alternate t slot on the cap fig 25 tighten the two clamping knobs 11
Turn then turn the machine screw located at the end of the stop fig 24 each full turn of the screw moves the stop surface exactly 11
Although the clamping pressure has been factory adjusted you may wish to fine tune the pressure to suit your individual 12
And follow the instructions beginning on page 14 12
Caution for your safety keep your hands behind the fence when moving to any new scale setting 12
Detail 27a 12
Feel if so use the thin plastic shims provided 12
Fig 26 12
Fig 27 12
In order for your incra shop stop to accurately locate your work piece for a cut you must first zero your shop stop to the cutter and position the sliding scale on your fence for most applications at the router table you will be using your shop stop on the outfeed fence to limit the length of a cut relative to the front end of a board follow the steps detailed in fig 26 to zero to your cutter once the shop stop is zeroed to the router bit as shown in fig 26 you now have the choice of setting the sliding scale on your incra fence to one of three initial positions see fig 27 and detail 27a 12
Moving the fence to any new scale setting is just as easy as moving any other fence you ve used before push the carriage clamp down to unlock the carriage then slide the fence as you sight through the hairline cursor when you see your measurement under the hairline cursor pull the clamp up to the locked position fig 28 remember that the ls positioner will only clamp every 12
Moving to a new scale setting 12
Operation 12
Or 1mm with the metric version so don t try to clamp in between scale marks it just won t work 12
Setting 12
Zeroing the shop stop 12
1 20mm for metric version of fence movement 13
1 40mm increments after micro adjusting you can re zero the dial to the pointer by rotating the dial not the red knob with your fingers see fig 30 13
1mm for metric version for smaller adjustments the black dial is marked in 13
Forward end of the carriage turn the knob clockwise to move the fence toward the cutter or counterclock wise to move the fence away from the cutter ball bearing engaged detents on the knob provide an audible click for each 13
In place gauging the distance moved when micro adjusting is easy a full turn of the knob equals 13
Lock the carriage clamp 13
Lower the carriage clamp to completely unclamp the carriage then raise the carriage clamp to the center position this center position for the carriage clamp softens the clamping pressure on the carriage to per mit movement during micro adjusting 13
Micro adjust the fence position 13
Micro adjusting your fence position 13
Pull the carriage clamp up to lock the carriage 13
Rotate the red micro adjust knob located at the 13
Set carriage clamp to micro adjust position 13
Zeroing the fence to your cutter 13
Adjusting the clamping pressure 14
Adjustments 14
All of the components and features of your new incra ls positioner have been factory set and should require no further adjustment if however you wish to adjust or recalibrate these components the following information is provided to assist in performing the adjustments 14
Applications 14
Fig 32 incra ls positioner 14
Fig 33 master reference guide 14
General purpose fence 14
Joint making 14
Note do not pull the carriage clamp up with the black uhmw bearing pad removed 14
Auto centering scale 15
Imperial model onl 15
Realigning the fence racks 15
Positioning the auto centering scale imperial model only 16
Using the auto centering scale 16
Warranty 16

Incra M-LS17WFNCSYS [3/16] Ls positioner super system

Содержание

Похожие устройства