![Incra M-LS17WFNCSYS [6/16] Pro ii fence installatio](/img/pdf.png)
Incra M-LS17WFNCSYS [6/16] Pro ii fence installatio
![Incra M-LS17WFNCSYS [6/16] Pro ii fence installatio](/views2/1628291/page6/bg6.png)
6 INCRA Woodworking Tools & Precision Rules
Once you have determined where the leading edge
of the LS Base will be positioned, mark a line on the
table at this spot. The line should be parallel to the
back edge of your router table. Measure back 1”
from this line and mark positions for (2)
5
/16” diameter
mounting holes spaced 5½” apart. Measure back
another 2” further and mark positions for (2) more
5
/16” diameter holes, Fig. 4. (If your table permits,
increase the spacing between the 2 sets of holes.)
Drill the holes.
Attach LS Base to your Router
Table
Open the LS Base Mounting Hardware Pack A-21.
Place the (4) ¼-20 x 2” hex bolts through the holes
in the table and loosely fasten with ¼” washers and
hex nuts. Now slide the heads of the bolts into the T-
slot located on the underside of the LS Base, Fig. 5.
Square the base to your table edge and tighten the
fasteners. Now slide the carriage back into the base
and pull the carriage clamp up to lock the carriage in
place.
FIG. 3
Extension
wing
2
Extending your router table length
Screw aluminum or steel angle to the
underside of the router table to provide
support arms for a table extension, Fig. 3.
The extension needs to be flush and parallel to
the table top. Shim into alignment as necessary.
Existing
router
table top
Wood
screws
Aluminum or steel angle
5½”
Drill
5
/16” diameter holes
Mark where leading
edge of LS Base will
be positioned
1”
2” minimum
Slide LS
Base onto
heads of hex bolts
¼-20 x 2” hex bolt
¼” flat washer
¼” hex nut
¼-20 x 1¾” pan
head Phillips screws
¼” flat washer
PRO II FENCE INSTALLATION
(STANDARD & SUPER
Note: If you have an “Incra ready” router table with
T-nuts installed in the pre-drilled mounting holes, use
the (6) ¼-20 x 1¾” pan head Phillips screws with ¼”
washers to attach the LS Base as shown in Fig. 6.
The Pro II Fence, included in both the Standard
and Super System packages, provides a 28”
long reference for all of your cutting operations.
Machined to perfection, it includes a 1” x 1” opening
to handle all of your grooving, dadoing, rabbeting
and joinery applications. The fence top includes
INCRA positioning racks that work in conjunction
with the INCRA Shop Stop for perfectly repeatable
stopped cuts. The self-storing stop extender bar
permits stopped cuts beyond the length of the
fence and the front T-slot allows easy attachment of
user-made sub fences or the Super System Wonder
Fence.
FIG. 6 Mounting for “Incra Ready” router
FIG. 4 Drill mounting holes
FIG. 5 Aach LS Base to router table
Содержание
- Contents 1
- Owner s manual 1
- Ls positioner standard system 2
- Ls positioner super system 3
- Auxiliary scale slots 4
- Carriage 4
- Getting acquainted 4
- Hairline cursor and view windows 4
- Important safety instructions for using the incra ls positioner 4
- Lead screw positioning element 4
- Ls base 4
- Safety 4
- Stainless steel primary scale 4
- Three position carriage clamp 4
- Drill mounting holes 5
- Fence mounting bracket 5
- Micro adjust knob 5
- Micro adjust scale dial 5
- Setup mounting to your router table 5
- Attach ls base to your router table 6
- Pro ii fence installatio 6
- Standard super 6
- Attaching the pro ii fence 7
- Installing pro ii extender bar and stop 7
- Adjusting the fence angle 8
- Attaching the wonder fence to the pro ii or ts fence 8
- Mounting an auxiliary fence to your pro ii fence 8
- Super system only 8
- Wonder fence installation 8
- Attach the fence cap braces 9
- Attaching the wonder fence hi rise fence cap 9
- 1mm for metric version the two piece body can be micro adjusted to any position between steps and can be configured to clamp to your fence even when using wooden sub fences up to ¾ thick follow the instructions on the next page to set up and use the shop stop 10
- Attach and align fence cap 10
- Attach the cap extender 10
- Detail 19a 10
- Fig 19 10
- Shop stop 10
- When used in conjunction with your new pro ii fence or wonder fence the incra shop stop provides the same precise positioning capabilities that your ls positioner offers the patented incremental positioning of incra s saw toothed racks found on the shop stop and your incra fence allow perfectly repeatable stop locations at any multiple of 10
- After removing the shop stop from the packaging loosen the two white nylon thumbscrews and clamp the stop to the outfeed end of your incra fence now loosen the 10 32 x 3½ phillips head screw and slide the red vertical stop arm onto the hex nut fig 22 make sure that the indexing lip on the arm wraps around the front of the stop body and that the arm is flat against the end of the body fig 23 tighten the fastener to secure the arm a short distance above your router table to provide clearance for sawdust the fastener and stop arm can be reversed for use at either end of your fence 11
- Approx 1mm when turning the screw counterclockwise push the stop body toward the screw always tighten the two black thumbscrews after micro adjusting 11
- Expanded clamping mode 11
- Fig 22 11
- Fig 23 11
- Fig 24 11
- Fig 25 11
- Fine tuning the position of your shop stop relative to a cutter is easy and accurate just loosen the two black thumbscrews on top of the shop stop body about 11
- Micro adjusting 11
- Shop stop assembly 11
- The two piece design of the incra shop stop permits use of a ¾ thick wooden auxiliary fence without interfering with the stop s ability to clamp to your incra fence to change the stop to expanded clamping mode loosen the two black thumbscrews and slide the stop body red off of the stop cap gold now slide the 2 rectangular nuts on the stop body into the alternate t slot on the cap fig 25 tighten the two clamping knobs 11
- Turn then turn the machine screw located at the end of the stop fig 24 each full turn of the screw moves the stop surface exactly 11
- Although the clamping pressure has been factory adjusted you may wish to fine tune the pressure to suit your individual 12
- And follow the instructions beginning on page 14 12
- Caution for your safety keep your hands behind the fence when moving to any new scale setting 12
- Detail 27a 12
- Feel if so use the thin plastic shims provided 12
- Fig 26 12
- Fig 27 12
- In order for your incra shop stop to accurately locate your work piece for a cut you must first zero your shop stop to the cutter and position the sliding scale on your fence for most applications at the router table you will be using your shop stop on the outfeed fence to limit the length of a cut relative to the front end of a board follow the steps detailed in fig 26 to zero to your cutter once the shop stop is zeroed to the router bit as shown in fig 26 you now have the choice of setting the sliding scale on your incra fence to one of three initial positions see fig 27 and detail 27a 12
- Moving the fence to any new scale setting is just as easy as moving any other fence you ve used before push the carriage clamp down to unlock the carriage then slide the fence as you sight through the hairline cursor when you see your measurement under the hairline cursor pull the clamp up to the locked position fig 28 remember that the ls positioner will only clamp every 12
- Moving to a new scale setting 12
- Operation 12
- Or 1mm with the metric version so don t try to clamp in between scale marks it just won t work 12
- Setting 12
- Zeroing the shop stop 12
- 1 20mm for metric version of fence movement 13
- 1 40mm increments after micro adjusting you can re zero the dial to the pointer by rotating the dial not the red knob with your fingers see fig 30 13
- 1mm for metric version for smaller adjustments the black dial is marked in 13
- Forward end of the carriage turn the knob clockwise to move the fence toward the cutter or counterclock wise to move the fence away from the cutter ball bearing engaged detents on the knob provide an audible click for each 13
- In place gauging the distance moved when micro adjusting is easy a full turn of the knob equals 13
- Lock the carriage clamp 13
- Lower the carriage clamp to completely unclamp the carriage then raise the carriage clamp to the center position this center position for the carriage clamp softens the clamping pressure on the carriage to per mit movement during micro adjusting 13
- Micro adjust the fence position 13
- Micro adjusting your fence position 13
- Pull the carriage clamp up to lock the carriage 13
- Rotate the red micro adjust knob located at the 13
- Set carriage clamp to micro adjust position 13
- Zeroing the fence to your cutter 13
- Adjusting the clamping pressure 14
- Adjustments 14
- All of the components and features of your new incra ls positioner have been factory set and should require no further adjustment if however you wish to adjust or recalibrate these components the following information is provided to assist in performing the adjustments 14
- Applications 14
- Fig 32 incra ls positioner 14
- Fig 33 master reference guide 14
- General purpose fence 14
- Joint making 14
- Note do not pull the carriage clamp up with the black uhmw bearing pad removed 14
- Auto centering scale 15
- Imperial model onl 15
- Realigning the fence racks 15
- Positioning the auto centering scale imperial model only 16
- Using the auto centering scale 16
- Warranty 16
Похожие устройства
- Stiga Combi 55 SQ B Инструкция по эксплуатации
- Champion G760HKE Инструкция по эксплуатации
- Champion G680HKE Инструкция по эксплуатации
- МЕГЕОН 13250 Инструкция по эксплуатации
- МЕГЕОН 13900 Инструкция по эксплуатации
- МЕГЕОН 13200 Инструкция по эксплуатации
- МЕГЕОН 13126 Инструкция по эксплуатации
- МЕГЕОН 13225 Инструкция по эксплуатации
- МЕГЕОН 13950 Инструкция по эксплуатации
- МЕГЕОН 19010 Инструкция по эксплуатации
- Grundfos SQ 1 - 50 (96510179) Инструкция по эксплуатации
- Grundfos SQE 1 - 110 (96510145) Инструкция по эксплуатации
- Grundfos SQ 1 - 110 (96510193) Инструкция по эксплуатации
- Grundfos SQE 2 - 70 (96510152) Инструкция по эксплуатации
- Grundfos SQE 2 - 55 (96510151) Инструкция по эксплуатации
- AM.PM C303411WH Инструкция по эксплуатации
- Grohe Sensia Arena 39354SH1 Инструкция по эксплуатации
- Orbis ORBIFOT (OB132200) Инструкция по эксплуатации
- Orbis ORBILUX (OB132012) Инструкция по эксплуатации
- Orbis VEGA (OB131712) Инструкция по эксплуатации