![Teka EM 30 2G [8/21] Connecting the electricity](/img/pdf.png)
Teka EM 30 2G [8/21] Connecting the electricity
![Teka EM 30 2G [8/21] Connecting the electricity](/views2/1069894/page8/bg8.png)
GB
8
TEKA assumes no responsibility
for any malfunction or damage caused
by faulty installation.
PLEASE REMEMBER THAT THE GUA-
RANTEE DOES NOT COVER THE
GLASS IF IT SUFFERS A VIOLENT
BLOW OR IF IT IS USED IMPROPERLY.
Positioning the oven
See the corresponding manual.
Fixing the hob
When the gap has been properly sized,
the sealing washer (J) should be put on
the lower part of the cooker.
Position the clips (K) as shown in figure 2,
fastening them to the openings in the
lower part of the body using the metal thre-
aded screws provided (Ø 4,2 mm).
The clips (K) and the sealing washer (J) are
provided, and can be found in the packaging.
Connecting the gas
Connecting the hob to the gas mains should
be done in compliance with the current ins-
tallation standards and regulations.
Ventilation slots should also be made at
the site in compliance with current norms.
The hob is provided with a threaded con-
nection 1/2” in diameter, in line with ISO
228-1. A Ø10/12 mm copper pipe is provi-
ded as an accessory for welding the gas
inlet pipe.
Whenever the gas connection nut is remo-
ved, its washer should be changed.
In order that the hob is not damaged by
tightening the nut on the gas connection
pipe, a maximum torque of 300 cm * Kgf
should be applied.
When the gas connection has been made,
the installation should be checked to ensu-
re that it is completely sealed. If the check
is done using air, care should be taken that
the test pressure is no more than 200
g/cm
2
. Where air is not available, soapy
water should be applied to ensure that
there are no leaks in the connections. Tes-
ting should never be done using a
flame.
When the hob has been installed, check
that the burner minimums are properly
adjusted. To do this, light the burners and
check that they do not go out if you switch
quickly from the maximum to the minimum.
Connecting the electricity
Before connecting the hob to the electric
mains, check that the voltage and fre-
quency of the mains matches what is
shown on the hob’s rating plate, which is
fig. 2
Содержание
- Inhaltsverzeichnis 2
- Indice 3
- Table des matières 3
- Introduction präsentation présentation presentazione 4
- Guide to using the instructions booklet 6
- Installation 7
- Positioning the hobs 7
- Connecting the electricity 8
- Connecting the gas 8
- Fixing the hob 8
- Positioning the oven 8
- Gas conversion 9
- Table 1 9
- Dimensions and power 10
- Technical information 10
- A before installation make sure that the local supply conditions the gas type and pressure are compatible with the applian ce s setup b the setup conditions for this appliance are written on the label or the rating plate c this appliance should not be connected to a device for removing combustion pro ducts it should be installed and connected in compliance with the current installation standards special attention should be paid to the regulations applying to ventilation 11
- A gas cooking appliance produ ces heat and moisture at the site where it is installed the kitchen should be provided with suitable ventilation natu ral ventilation sources should be kept 11
- Class 3 hob 11
- Clear a window opened or an effective mechical ventilation system device such as a hood installed 11
- Common features for all models with electric hotplates and auto matic ignition 11
- Common features for all models with gas burners 11
- If an electric hotplate gets cracked the hob should be disconnected from the elec tricity current 11
- If the appliance is used intensi vely over a sustained period of time it may require supplementary ventilation such as an open window or more effec tive ventilation for example an increa se in the power of the mechanical ven tilation if this is present 11
- Table 2 11
- Table 3 11
- Technical information 11
- The supply voltage and frequency will be as shown on the rating plate 11
- Warnings 11
- You should keep the guarantee certificate or where relevant the techni cal datasheet together with the instruc tion manual for the duration of the useful life of the appliance it has important tech nical information about the appliance 11
- Igniting the burners 12
- Special requirements before starting for the first time 12
- Use and maintenance 12
- Anti accidental turn system on gas controls 13
- Safety system components fig 4 13
- Cleaning and looking after the burners 14
- Right wrong 14
- Suggestions for effective use of the burners 14
- Maintaining the burners 15
- Operation of models with electric hotplates 15
- Of the electric hotplates 16
- Suggestions for effective use 16
- Cleaning and looking after the hotplates 17
- Operating the glass ceramic hotplates 17
- Advice on using the electric hotplates effectively 18
- Cleaning and looking after glass ceramic hobs 19
- If something doesn t work 21
Похожие устройства
- Sony NWZ-Z1040 8Gb Black Инструкция по эксплуатации
- Intro Omega 1 ver 9.0 Инструкция по эксплуатации
- Explay PN-375 Инструкция по эксплуатации
- Teka EM 30 2P Инструкция по эксплуатации
- Sony NWZ-Z1040 8Gb Red Инструкция по эксплуатации
- Intro DPA-05 Mazda Инструкция по эксплуатации
- Teka VT TC 2P.1 Инструкция по эксплуатации
- Sony NWZ-Z1060 32Gb Black Инструкция по эксплуатации
- Intro AMP-HY02 Hyundai Инструкция по эксплуатации
- Teka EH 60 4G AI AL TR CI NAT BEIGE MG Инструкция по эксплуатации
- Texet T-119 4Gb Violet Инструкция по эксплуатации
- Intro AMP-KIA Инструкция по эксплуатации
- Teka EH 60 4G AI AL TR CI NAT ANTRACITE Инструкция по эксплуатации
- Ritmix RF-4310 4Gb Purple Инструкция по эксплуатации
- Intro AMP-MT01 Citroеn Инструкция по эксплуатации
- Teka EH 60 4G AI AL TR CI NAT BEIGE OB Инструкция по эксплуатации
- Olympus VN-711PC 2Gb Инструкция по эксплуатации
- Intro AMP-MT02 Peugeot Инструкция по эксплуатации
- Teka EH 60 4G AI AL TR CI NAT ANTRACITE OB Инструкция по эксплуатации
- Olympus VN-713PC 4Gb Инструкция по эксплуатации