Einhell BT-AC 240/50/10 OF [15/84] Replacing the power cable

Einhell BT-AC 240/50/10 OF [15/84] Replacing the power cable
6.3 Voltage
Before you use the machine, make sure that the
mains voltage complies with the specifications on the
rating plate. Long supply cables, extensions, cable
reels etc. cause a drop in voltage and can impede
motor start-up. In the case of low temperatures
below +5°C, motor start-up is jeopardized as a result
of stiffness.
6.4 On/Off switch (8)
To switch on the compressor, press the button (8).
To switch off the compressor, press the button (8)
again (Fig. 1).
6.5 Adjusting the pressure: (Fig. 1)
You can adjust the pressure on the pressure
gauge (6) using the pressure regulator (7).
The set pressure can be taken from the quick-
lock coupling (5).
6.6 Setting the pressure switch
The pressure switch is set at the factory.
Switch-on pressure 8 bar
Switch-off pressure 10 bar
7. Replacing the power cable
If the power cable for this equipment is damaged, it
must be replaced by the manufacturer or its after-
sales service or similarly trained personnel to avoid
danger.
8. Cleaning and maintenance
Important!
Pull the power plug before doing any cleaning
and maintenance work on the appliance.
Important!
Wait until the compressor has completely cooled
down. Risk of burns!
Important!
Always depressurize the tank before carrying out
any cleaning and maintenance work.
8.1 Cleaning
Keep the safety devices free of dirt and dust as
far as possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
We recommend that you clean the appliance
immediately after you use it.
Clean the appliance regularly with a damp cloth
and some soft soap. Do not use cleaning agents
or solvents; these may be aggressive to the
plastic parts in the appliance. Ensure that no
water can get into the interior of the appliance.
You must disconnect the hose and any spraying
tools from the compressor before cleaning. Do
not clean the compressor with water, solvents or
the like.
8.2 Condensed water (Fig. 7)
Important. To ensure a long service life of the
pressure vessel (2), drain off the condensed water by
opening the drain valve (1) each time after using. To
open you must turn the cock on the drain screw
through 90°. Tilt the vessel so that the drain screw is
the lowest point of the vessel and the condensed
water can drain off completely. To close again, turn
the cock back through 90°. Check the pressure
vessel for signs of rust and damage each time before
using. Do not use the compressor with a damaged or
rusty pressure vessel. If you discover any damage,
please contact the customer service workshop.
8.3 Storage
Important!
Pull the mains plug out of the socket and ventilate
the appliance and all connected pneumatic tools.
Switch off the compressor and make sure that it is
secured in such a way that it cannot be started up
again by any unauthorized person.
Important!
Store the compressor only in a dry location
which is not accessible to unauthorized persons.
Always store upright, never tilted!
8.4 Carbon brushes
In case of excessive sparking, have the carbon
brushes checked only by a qualified electrician.
Important! The carbon brushes should not be rep
laced by anyone but a qualified electrician.
GB
15
Anleitung_BT_AC_240_50_10_SPK7:_ 20.01.2011 10:29 Uhr Seite 15

Содержание

Anleitung BT AC 240 50 10 SPK7 20 01 20 10 29 Uhr Seite 15 GB 6 3 Voltage Before you use the machine make sure that the mains voltage complies with the specifications on the rating plate Long supply cables extensions cable reels etc cause a drop in voltage and can impede motor start up In the case of low temperatures below 5 C motor start up is jeopardized as a result of stiffness 6 4 On Off switch 8 To switch on the compressor press the button 8 To switch off the compressor press the button 8 again Fig 1 6 5 Adjusting the pressure Fig 1 You can adjust the pressure on the pressure gauge 6 using the pressure regulator 7 The set pressure can be taken from the quick lock coupling 5 6 6 Setting the pressure switch The pressure switch is set al the factory Switch on pressure 8 bar Switch off pressure 10 bar 7 Replacing the power cable If the power cable for this equipment is damaged it must be replaced by the manufacturer or its after sales service or similarly trained personnel to avoid danger 8 1 Cleaning Keep the safety devices free of dirt and dust as far as possible Wipe the equipment with a clean cloth or blow it with compressed air at low pressure We recommend that you clean the appliance immediately after you use it Clean the appliance regularly with a damp cloth and some soft soap Do not use cleaning agents or solvents these may be aggressive to the plastic parts in the appliance Ensure that no water can gel into the interior of the appliance You must disconnect the hose and any spraying tools from the compressor before cleaning Do not clean the compressor with water solvents or the like 8 2 Condensed water Fig 7 Important To ensure a long service life of the pressure vessel 2 drain off the condensed water by opening the drain valve 1 each time after using To open you must turn the cock on the drain screw through 90 Till the vessel so that the drain screw is the lowest point of the vessel and the condensed water can drain off completely To close again turn the cock back through 90 Check the pressure vessel for signs of rust and damage each lime before using Do not use the compressor with a damaged or rusty pressure vessel If you discover any damage please contact the customer service workshop 8 3 Storage Important 8 Cleaning and maintenance Important Pull the power plug before doing any cleaning and maintenance work on the appliance Important Wait until the compressor has completely cooled down Risk of burns Important Always depressurize the tank before carrying out any cleaning and maintenance work Pull the mains plug out of the socket and ventilate the appliance and all connected pneumatic tools Switch off the compressor and make sure that it is secured in such a way that it cannot be started up again by any unauthorized person Important Store the compressor only in a dry location which is not accessible to unauthorized persons Always store upright never tilted 8 4 Carbon brushes In case of excessive sparking have the carbon brushes checked only by a qualified electrician Important The carbon brushes should not be rep laced by anyone but a qualified electrician 15

Скачать