Coolfort CF-3204 [9/52] Press the button 47 on the remote control
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Coolfort CF-3204 [9/52] Press the button 47 on the remote control

Coolfort CF-3204 [9/52] Press the button 47 on the remote control
9
ENGLISH
the robot, after which the voice alert will sound «Starting
wet cleaning». To suspend the selected mode, press the
buttons again.
Warning:
–
To extend the service life of the water tank, it is recom-
mended to use clean water or softened water.
–
Please do not use the wet cleaning function on the carpet.
–
At the end of wet cleaning, clean the water tank.
–
It is recommended to wash and dry the cloth from the
attachment (29) after each wet cleaning to prevent the
appearance of smell or mold.
–
After 60 minutes of cleaning, it is recommended to clean
the cloth (29) to reduce water consumption.
–
If you do not plan to carry out wet cleaning, it is necessary
to remove the attachment (30) from the robot.
Enabling Wi-Fi pairing mode
(Only to be used in accordance with the COOLFORT mobile
app instruction manual)
•
Robot is connected to the charging station:
–
press and hold the « » button (16) for more than
5 seconds – you will hear a sound notification and the
« » Wi-Fi indicator (15), as well as the « » button
indicator (16) will slowly begin to flicker.
•
Robot is not connected to the charging station:
–
switch the robot on by using the «I/O» power switch
(20);
– press the « » button (47) on the remote control
once, or press and hold the « » button (16) for
more than 5 seconds – you will hear a sound noti-
fication and the « » Wi-Fi indicator (15), as well
as the « » button indicator (16) will slowly begin
to flicker.
CLEANING AND MAINTENANCE
(Thoroughly study the VACUUM CLEANER ASSEMBLY
section before cleaning)
Cleaning the dust bin
•
Open the robot upper lid (12) and pull the dust bin (11)
by the handle (27) (fig. 16).
•
Press the dust bin lid lock (26) and open the lid (25).
•
Remove the dust and garbage (fig. 17) from the dust
bin (11).
•
Remove the filter holder (23) and extract the HEPA filter
(24) from it (fig. 18).
•
Clean the dust box lid and the fine mesh using a tissue
(fig. 19) and the cleaning brush (37), remove any foreign
objects from the valve (28).
•
Wash the dust bin (11) with warm running water. Clean
the HEPA filter (24) using the cleaning brush (37) while
carefully tapping it against a hard surface (fig. 20).
•
Let the dust bin and filter components dry naturally
(fig. 21). Keep them dry in order to extend their ser-
vice life.
Turbo Brush cleaning
•
Remove the turbo brush frame holder (8), by pressing
the locks and pulling them upwards, in the direction
of arrows in Fig. 22. Then remove the turbo brush (10)
from its socket. Cut the entangled around the Brush hair
and thread with scissors and remove it, using the clean-
ing brush (37).
•
Clean the brush from dust and wipe it with a clean,
slightly damp tissue.
•
Wipe the brush socket, suction orifice of the robot,
frame guard, and turbo brush driving shaft with a clean,
slightly damp tissue.
•
Reinstall the brush in the following manner:
–
Install one end of the brush on the driving shaft in
careful wiggling motions.
–
Lower the other end of the brush into the socket and
secure it with the frame guard.
–
Make sure that the frame is properly secured.
Side brushes cleaning (fig. 23)
It is best to remove any hair entangled around the brushes
before cleaning.
•
To remove the side brush (2, 5), pull it upwards by its
two straps.
•
Cut any hair and thread entangled around the driving
shafts with scissors.
•
Cut any hair and thread entangled around the side
brushes with scissors.
•
Clean the brushes from dust and wipe them with a clean,
slightly damp tissue.
•
Reinstall the side brushes, observing the color markings
on the brushes and the driving shafts.
Cleaning the water tank (21) and the floor wet
cleaning accessory (9)
•
Press the key (22) and pull the water tank (21) out of the
robot vacuum cleaner body (fig. 24).
•
Remove the wet cleaning accessory (9) (fig. 25).
•
Remove the microfiber cloth (29), by pulling in the direc-
tion of the arrow, depicted in Fig. 26.
•
Remove the plug (31) and drain any remaining water
from the water tank (21) (fig. 27).
•
Wash the water tank (21) with warm running water, then
wipe it, and let it dry (fig. 28 and 29).
• Remove the filter guard screws at the bottom of
the water tank (21). Remove the Filter, wash it with
warm running water, let it dry, and reinstall it (fig. 30
and 31).
•
Wash the microfiber cloth (29), under a warm water
stream, then let it dry naturally (fig. 32 and 33).
Robotic vacuum cleaner body
and charging station cleaning
•
Clean and wipe the anti-drop sensors (1), located on the
lower part of the robot vacuum cleaner body (fig. 34).
•
If you hear squeaking while the vacuum cleaner is mov-
ing, clean the axis of its front wheel (fig. 35).
•
Using a flat-head screwdriver, extract the front wheel
(4) from its socket and remove the metal axis. Remove
any hair and thread entangled around the axis. Using
the cleaning brush, clean the wheel socket and the
axis guards. Clear any dust and garbage off the wheel,
remove hair if it is present.
•
Insert the wheel into the axis and reinstall it back into its
socket. Make sure that nothing hinders free rotation of
the wheel (4).
•
Clear off any dust the battery charging contacts (3) of
the vacuum cleaner and the charging station contacts
(34) (fig. 36).
•
Wipe the signal window (33) of the charging station (32)
(fig. 36).
•
Wipe the bumper (13), keep the bumper clean, as it
hosts the movement sensors window (17) (fig. 37).
•
Wipe the body of the vacuum cleaner with a clean,
slightly damp tissue, then wipe it dry.
•
Do not submerge the vacuum cleaner body, charging
station (32), power supply unit (36), power supply unit
connector cable into water or any other liquids. Make
sure that no liquid enters the vacuum cleaner body.
•
Do not use solvents or abrasives for the cleaning of the
vacuum cleaner body, charging station, or the power
supply unit.

Содержание

Похожие устройства

Скачать