![Foxconn nt-ibt29-0h0wbae [25/55] Smart bios](/img/pdf.png)
Foxconn nt-ibt29-0h0wbae [25/55] Smart bios
![Foxconn nt-ibt18-0h0wbae [25/55] Smart bios](/views2/1167518/page25/bg19.png)
19
BIOS SETUP
Smart BIOS
► Smart Power LED
Smart Power LED is a feature built on your motherboard to indicate different states during Power On
Self Test (POST). The LED is located at the front panel, and it displays POST state by different long-
short blinking intervals. You can always leave this state enabled.
System Status Power LED Status Stop Blinking Condition
Normal Always On Always On
No Memory Continue blinking On (1sec.), Off (1sec.) Reboot & Memory OK
No Display Continue blinking On (2sec.), Off (2sec.) Reboot & Display OK
Post Error Message
Quick blinking twice (1/3sec. On, 1/3sec. Off),
one long On (1sec.), continuously.
Enter Setup or Skip
Main Advanced Boot Power Health Security Save&ExitF-center
→ ←: Select Screen
↑ ↓/Click: Select Item
Enter/Dbl Click: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC/Right Click: Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
Smart Power LED [Disabled]
Smart Boot Menu [Enabled]
Smart Power LED
Settings
Содержание
- Nanopc user s manual 1
- Safety notice 3
- Package contents 4
- Bios setup 5
- Introduction 5
- Placement and connecting 5
- Table of contentes 5
- Table of contents 5
- Install os 6
- Utility 6
- Introduction 7
- 1 front side view 8
- Introduction 8
- Introduction 9
- 2 back side view 10
- Introduction 10
- Introduction 11
- 3 ddr3 ddr3l jumper 12
- Introduction 12
- Set the jumper to pins 1 2 it set to ddr3l the ddr3l power is 1 5v set the jumper to pins 2 3 it set to ddr3 the ddr3 power is 1 v 12
- Placement and connecting 13
- 1 placement of nanopc 14
- In seat base 14
- On the desk 14
- Placement and connecting 14
- Installing to display 15
- Placement and connecting 15
- 2 connection of nanopc 16
- Connect display 16
- Placement and connecting 16
- Connect network cable 17
- Connect usb devices 17
- Placement and connecting 17
- Connect power cord 18
- Placement and connecting 18
- Connect one end of cable to the com port and the other end to a point of sales connect one end of cable to the com port and the other end to a point of sales 19
- Connect point of sales 19
- Placement and connecting 19
- Bios setup 20
- Bios setup 21
- Enter bios setup 21
- Bios setup 22
- Bios setup 23
- Respectively access level it displays your current access level if you enter system with a user password it will display user if 23
- Bios setup 24
- F center 24
- No password is set or you enter system with administrator password this item will display administrator 24
- To go to relative submenu 24
- Bios setup 25
- Smart bios 25
- Smart power led smart power led is a feature built on your motherboard to indicate different states during power on self test post the led is located at the front panel and it displays post state by different long short blinking intervals you can always leave this state enabled 25
- Bios setup 26
- Fox intelligent stepping 26
- Smart boot menu 26
- Spread spectrum if you enabled this function it can significantly reduce the emi electromagnetic interference generated by the system so to comply with fcc regulation but if overclocking is activated you had better disable it 26
- When pc starts it will ask you to press del key to enter setup or press f7 key to enter smart boot menu if disabled is selected then pressing f7 has no function this also prevents user without password trying to get into your computer through smart boot menu 26
- Bios setup 27
- Cpu configuration 27
- Intel xd bit this item is used to enable disable the execute disable bit feature intel s execute disable bit functionality can help prevent certain classes of malicious buffer overflow attacks when combined with a supporting operating system limit cpuid maximum this item is used to enable or disable cpuid maximum value limit configuration set limit cpuid maximum to 3 should be disabled for winxp intel virtualization technology appears only when cpu supports virtualization i e intel vanderpool technology allows a platform to run multiple operating systems and applications in independent partitions or containers one physical compute system can function as multiple virtual systems vanderpool technology can help improve future virtualization solutions this item will be displayed only when the cpu is supporting this feature and the setting is used to enable disable it 27
- Bios setup 28
- Advanced 29
- Bios setup 29
- Realtek pcie gbe family controller mac 00 00 00 00 00 03 29
- To go to get driver information and configure realtek ethernet controller patameter 29
- Trusted computing north bridge txe subsystem onboard device configuration sata configuration super io configuration network stack 29
- Bios setup 30
- Configuration security device support disabled 30
- Current status information no security device found 30
- Security device support this item is used to enable or disable bios support for security device o s will not show security device tcg efi protocol and inta interface will not be available 30
- Trusted computing 30
- Bios setup 31
- Integrated graphics device enabled dvmt pre allocated 64m dvmt total gfx memory 256mb 31
- North bridge 31
- Total memory this item displays the current using memory information memory slot 0 these items display the memory size installed on each slot dvmt pre allocated this item is used to select dvmt 5 pre allocated fixed graphics memory size used by the internal graphics devices dvmt total gfx memory this item is used to select dvmt 5 total graphic memory size used by internal graphics device 31
- Bios setup 32
- Txe subsystem 32
- Txe version it displays the current txe version 32
- Bios setup 33
- Onboard device configuration 33
- Bios setup 34
- Sata configuration 34
- Bios setup 35
- Super io configuration 35
- Bios setup 36
- Network stack configuration 36
- Network stack disabled 36
- Network stack this item is used to enable disable uefi network stack the uefi unified extensible firmware interface network stack implements the tcp ip network interfaces such as snp mnp arp ip udp dhcp mtftp and tcp 36
- Bios setup 37
- Bootup numlock state this item defines if the keyboard num lock key is active when your system is started the available settings are on default and off quiet boot this item is used to enable disable the quiet boot disabled displays the normal post messages enabled displays oem customer logo instead of post messages fast boot this item is used to enable or disable boot with initialization of a minimal set of devices required to launch active boot option this is no effect for bbs boot options fixed boot order priorities these items are used to set the system boot order 37
- Bios setup 38
- Compatibility support module configuration csm support disabled 38
- Csm parameters 38
- Csm support this item is used to enable or disable csm support 38
- Enable disable csm support 38
- Hard disk drive bbs priorities cd dvd rom drive bbs priorities usb floppy drive bbs priorities usb cd dvd rom drive bbs priorities usb hard disk drive bbs priorities usb key drive bbs priorities network device bbs priorities uefi boot drive bbs priorities this items appear only when the devices are available use this items to specify the boot device priority sequence of the detected devices 38
- Bios setup 39
- Bios setup 40
- Cpu shutdown temperature this item is used to set the system temperature upper limit when the temperature exceedsthe set value the system will shut down automatically this function works only when your operating system is supporting acpi cpu smart fan control this option is used to enable or disable cpu smart fan function 40
- Health 40
- Restore ac power loss this item is used to set which state the pc will take with when it resumes after an ac power loss 40
- Bios setup 41
- Security 41
- Bios setup 42
- Save exit 42
- Bios setup 43
- Install os 44
- 1 install windows 8 windows 8 windows 7 64 bit 45
- Install os 45
- Install os 46
- Install os 47
- Install os 48
- 2 install drivers 49
- Install os 49
- Utility 50
- Fox winflash 51
- Local update 51
- Utility 51
- Utility 52
- About help 53
- Utility 53
Похожие устройства
- Foxconn nt-ibt19-0h0wbae Инструкция по эксплуатации
- Foxconn at-5570 Инструкция по эксплуатации
- Foxconn at-9330 black Инструкция по эксплуатации
- Foxconn at-9500 black Инструкция по эксплуатации
- Foxconn at-9700 black Инструкция по эксплуатации
- Foxeye gc1 moto cam Инструкция по эксплуатации
- Falcon Eye fe, fe-100m Инструкция по эксплуатации
- Falcon Eye fe, fe-200w Инструкция по эксплуатации
- Falcon Eye fe-4hp2 + avp-506 + fe-2369 + ат-12/30 Инструкция по эксплуатации
- Falcon Eye fe-201avr Инструкция по эксплуатации
- Falcon Eye fe-kit квартира Инструкция по эксплуатации
- Protherm FE 120/6 BM Инструкция по эксплуатации
- Protherm FE 150/6 BM Инструкция по эксплуатации
- Protherm FE 200/6 BM Инструкция по эксплуатации
- Protherm WH B60Z Инструкция по эксплуатации
- Protherm FS B 100 MSR Инструкция по эксплуатации
- Protherm Бобер 20 DLO Инструкция по эксплуатации
- Protherm Бобер 20 DLO Технические характеристики
- Protherm Бобер 20 DLO Сертификат
- Protherm Бобер 30 DLO Инструкция по эксплуатации