![Autel MaxiCheck PRO Руководство пользователя онлайн [73/76] 171295](/img/pdf.png)
Autel MaxiCheck PRO Руководство пользователя онлайн [73/76] 171295
![Autel MaxiCheck PRO Руководство пользователя онлайн [73/76] 171295](/views2/1200933/page73/bg49.png)
71
4. The tool may display information during and after the test. The
information varies by vehicle.
Figure 8.19
5. When the test is finished, there may be three results displaying
on the screen.
The test is finished successfully.
The test is stopped by the user.
The test did not finish.
In the first condition, the tool will display an information screen as
“The operation was performed correctly. Put the vehicle on a
vehicle lift and check that the rear wheels are locked. Check
that the 'Electric parking brake on' message is display on the
control panel and that the LED illuminates on the control
panel.”
In the second condition, the tool will display an information screen
as “Operation of the actuator test was stopped by the user.
Press „Cancel' to go back to the list of possible operations.”
In the third condition, the tool will display an information screen as
“The actuator test did not finish operating. Please perform the
following check: Read the faults to resolve any possible faults
relating to the electric motor or to the cables.”
IMPORTANT: Make sure that the components to be tested are
not physically damaged and are well assembled.
Apply electric parking brake
Listen to the noise of the
Electric motor!
OK
Содержание
- Table of contents 1
- Safety precautions and warnings 3
- Diagnostic trouble codes dtcs 4
- General information 4
- On board diagnostics obd ii 4
- Location of the data link connector dlc 5
- Obd ii readiness monitors 6
- Obd ii monitor readiness status 7
- Obd ii definitions 8
- Tool description 10
- Using the scan tool 10
- Accessories included 12
- Keyboard 12
- Specifications 12
- System setup 13
- Language setup 14
- To enter the setup menu 14
- Unit of measure 15
- Beep set 16
- Key test 16
- Lcd test 17
- Product troubleshooting 18
- Vehicle coverage 18
- Playback data 20
- Reviewing data 20
- Deleting data 21
- Printing data 21
- Obdii diagnostics 22
- Read codes 23
- Erasing codes 26
- Live data 27
- Viewing data 28
- Recording data 31
- Freeze frame 33
- Retrieving i m readiness status 34
- Figure 5 1 37
- Figure 5 2 37
- If the vehicle supports readiness test of this drive cycle a 37
- Information is available on more than one page or use the left right scroll button to view pids in the previous next page 37
- O2 monitor test 37
- Obd2 regulations set by sae require that relevant vehicles monitor and tests on the oxygen o2 sensors to identify problems related to fuel efficiency and vehicle emissions these tests are not on demand tests and they are done automatically when engine operating conditions are within specified limits these test results are saved in the on board computer s memory 37
- Press the esc button to return to diagnostic menu 37
- Screen of the following displays figure 5 2 37
- Use the up down scroll button for more pids if additional 37
- On board monitor test 39
- Component test 42
- Viewing vehicle information 43
- Dtc lookup 45
- Modules present 45
- After you input the dtc code select finish and the scan tool will display this code s definition on screen 46
- Figure 5 0 46
- Figure 5 1 46
- Figure 5 9 46
- Press yes or ok button to proceed the scan tool will display dtc definition as below 46
- Select show and a soft keyboard will pop up use left right button and up down button to move to the desired character then press ok button to confirm 46
- Print and update 48
- Print data 48
- Register the tool 49
- Software update 49
- Update procedure 50
- View or delete programs 53
- General information 55
- Oil reset 55
- Reset operation 55
- A manual reset 56
- After entering the vehicle information the scan tool displays manual reset message as below 57
- Figure 7 57
- Follow the instructions to reset the service manually 57
- Press esc button to exit 57
- B auto reset 58
- After you have entered the vehicle information the oil reset screen will display as below 59
- Figure 7 59
- In the oil reset menu select service zero reset function and press ok button 59
- The instrument panel option enables you to finish oil reset service in one step by resetting the ecu to default values automatically the procedures work as below 59
- The tool will automatically begin resetting the vehicle ecu to default values 59
- Figure 7 60
- Figure 7 0 60
- Figure 7 1 60
- In the oil reset menu select resetting to zero of the service mileage function and press ok button 60
- The bsi option enables you to finish oil reset service automatically and manually the procedures work as below 60
- When the resetting is finished the tool will display a confirmation message 60
- Figure 7 2 61
- Figure 7 3 61
- Figure 7 4 61
- For the first maintenance threshold you have two choices select the correct option and press ok button to save the change 61
- Function and press ok button the screen will display the preset maintenance information of the vehicle the information items vary with different vehicles 61
- In the oil reset menu figure 7 1 select maintenance 61
- The tool will reset the oil service to zero automatically 61
- Figure 7 3 63
- When you have finished your configuration select finish key on the bottom of the screen then the tool will begin the oil reset service 63
- Epb maintenance 64
- Epb safety 64
- Described before please refer to chapter 5 obdii diagnostics for details 66
- Figure 8 66
- In the diagnostic menu figure 8 use the up down button to select special function to do the epb test which includes brake cable replacement and electric parking brake replacement 66
- In the epb screen use the up down button to select brake cable replacement the screen shows as below 66
- Special function 66
- A put in fitting or removal position 67
- Figure 8 67
- In the brake cable replacement screen the tool can perform three functions 67
- This function enables you to fit in or remove the brake cable safely and easily it will take a few seconds to execute this command 67
- When the job is done successfully the tool will display a message to confirm 67
- B cable tensioning 68
- Figure 8 68
- If the job fails to finish the tool will display a message to remind user of a problem after you exit the diagnosis program please repair the problem immediately 68
- Once the brake cable is fit in you would use this function to adjust its tension it will take a few seconds to execute this command 68
- C electric parking brake calibration 69
- Figure 8 0 69
- Figure 8 1 69
- If the job fails to finish the tool will display a message to remind user of a problem after you exit the diagnosis program please repair the problem immediately 69
- This function is to check if the epb is working correctly which should be performed after work has been completed on the epb or vehicle braking system it will remove any air gap from the brake pads and check the epb pressure 69
- When both functions above have completed successfully you still need to calibrate the electric parking brake system 69
- When the job is done successfully the tool will display a message to confirm 69
- After you select this function the tool will automatically work in the following procedure 70
- Figure 8 2 70
- Figure 8 3 70
- Figure 8 4 70
- When the job is done successfully the tool will display a message to confirm 70
- Figure 8 5 71
- Figure 8 6 71
- Figure 8 7 71
- If the job fails to finish the tool will display a message to remind user of a problem after you exit the diagnosis program please repair the problem immediately 71
- In the epb screen use the up down button to select electric parking brake replacement the screen shows as below 71
- Active test 72
- Abs maintenance 74
- Figure 8 0 74
- Figure 8 1 74
- In the abs diagnostic function the tool can read codes erase codes record live data read ecu information perform active test and perform special function for the functions already being described before please refer to chapter 5 obdii diagnostics for details 74
- In the diagnostic menu figure 8 0 use the up down button to select special function to do the abs test the scan tool displays as below 74
- In the system menu figure 8 use up down button to select abs to do abs maintenance the scan tool displays as below 74
- Special function 74
- Warning please stop repairing the components to be tested before the test starts and keep a certain distance during the test 74
- Active test 75
- Figure 8 2 75
- Figure 8 3 75
- In the active menu use the up down button to select the desired actuator to begin test if the selected actuator works correctly the tool will display a confirmation message as below figure 8 3 otherwise it will display a message to remind user of a problem after you exit the diagnosis program please repair the problem immediately 75
- In the diagnostic menu figure 8 0 use the up down button to select active test to do the actuator test the scan tool displays as below 75
- In the epb menu select the desired function and press ok button if the operation is finished successfully the scan tool will display a confirmation message otherwise it will display a message to remind user of a problem after you exit the diagnosis program please repair the problem immediately 75
- Limited one year warranty 76
- Service procedures 76
- Warranty and service 76
Похожие устройства
- Autel MaxiCheck Oil Light/Service Reset Руководство пользователя
- Autel MaxiCheck EPB Руководство пользователя
- Autel Maxivideo MV201 8.5 мм Руководство пользователя
- Autel Maxivideo MV400 5.5 мм Руководство пользователя
- Autel Maxivideo MV400 8.5 мм Руководство пользователя
- Coolfort CF-1216 Инструкция по эксплуатации
- Coolfort СF-1221 Инструкция по эксплуатации
- Coolfort CF-0525GY Инструкция по эксплуатации
- Cremesso Compact Automatic Burgundy Red Инструкция по эксплуатации
- Cremesso LM 600 Инструкция по эксплуатации
- Cuckoo CMC-CHSS1004F Инструкция по эксплуатации
- Defender Optimum MS-125 Nano Инструкция по эксплуатации
- Defender Game Racer Turbo GT Инструкция по эксплуатации
- Delonghi VVX 1885 Stirella Инструкция по эксплуатации
- Delonghi CTI 2103.BZ Инструкция по эксплуатации
- Delonghi CTI 2103.CP Инструкция по эксплуатации
- Delonghi CTI 2103.W Инструкция по эксплуатации
- Delonghi CTI 2103.BK Инструкция по эксплуатации
- Delonghi VVX 1680 Stirella Инструкция по эксплуатации
- Cremesso Compact Manual Shiny Silver Инструкция по эксплуатации