Gorenje K17TR [17/45] Using the appliance

Gorenje K17TR [17/45] Using the appliance
17
Staff kitchen areas in shops, offices and
other working environments;
Farm houses;
By clients in hotels, motels and other
residential type environments;
Bed and breakfast type environments.
Save these instructions. 28.
This appliance is marked according to
the European directive 2002/96/EC on
Waste Electrical and Electronic
Equipment (WEEE). This guideline is the
frame of a European-wide validity of
return and recycling on Waste Electrical
and Electronic Equipment.
USING THE APPLIANCE
Boil water
Place the unit on the level surface. 1.
To fill the kettle, remove it from the power base 2.
and open the lid by pressing the lid release
button. Fill it with the desired amount of water,
and then close the lid. You can fill the water
also through the spout. The water level should
not exceed MAX marks or sit below MIN level.
If you do not fill the kettle with enough water, it
will switch off before the water is boiled.
NOTE: Do not fill the water over the maximum
level. Water may spill out of the spout when
boiling. Ensure that the lid is firmly placed
before plugging the power outlet.
Position the kettle on the power base. 3.
Plug the kettle to the power outlet. The LCD will 4.
display the original water temperature (room
temperature) in the kettle.
Press theON/OFF” button once. The blue 5.
indicator ofON/OFFwill light up, the kettle will
boil the water and the water temperature
number on the LCD will change according to
the changing water temperature in the kettle.
CAUTION: If the kettle is not placed on the
power base after plugging, the LCD will
display“- -. After beeps, the backlight shut off
after 60S. This is a warning to place the kettle
on the power base.
Once the water is boiled, the kettle will shut off
6.
power automatically. After three beeps and the
ON/OFF indicator button will shut off. During
boiling, you may also press the ON/OFF
button again to stop entire operation.
NOTE: IF the lid is not firmly closed, the kettle
will not turn on.
After boiling, you can lift the kettle from the 7.
power base and then pour the water.
NOTE: Be careful while pouring the water from
your kettle. You can get scald because of the
hot water. Dont open the lid while the water in
the kettle is hot.
The kettle will not re-boil water until you press 8.
ON/OFF button again. You can store the kettle
on the power base, when you do not use it.
NOTE: Always disconnect the power supply
when you do not use the kettle.
Boil water first and keep warm on
preset temperature
Follow the previous steps 1-4 of Boil water. 1.
First press the ON/OFF button, then press the 2.
+ or - to set the keep warm temperature
(60, 70, 80 and 90). The kettle will boil
the water, then reduce the temperature to the
corresponding temperature and keep it warm.
The LCD will display and flash the preset keep 3.
warm temperature value for 5s. The blue
ON/OFF indicator will flash all the time.
When water is boiled, you will hear three 4.
beeps. ON/OFF indicator will still flash.
Afterwards the heating will stop and the water
temperature will be reduced to the keep warm
temperature. After reducing you will hear five
beeps and the LCD will display the preset keep
warm temperature instead of the practical water
temperature in the kettle. The ON/OFF
indicator will blink slowly all the time.
Note: During keep warm, the thermostat will still
work to maintain the water in the preset
keeping warm temperature.
During keep-warm, you may press the 5.
ON/OFF” button again to stop the entire
operation.
I you do not use the kettle, it will shut off 6.
automatically after two hours. The ON/OFF
button will also shut off.
Boil water to preset temperature
and maintain that temperature
Follow the previous steps 1-4 of Boil water. 1.
Press the + or - button to set the keep warm 2.
temperature (60, 70, 80 and 90). The
LCD will display and flash the preset keep
warm temperature value for 5s.
Press the ON/OFF button within 5s. The kettle 3.
will heat water to the preset temperature and
maintain the temperature.
Note: If you do not press any button within 5s,
the kettle will return to the standby state. The
LCD will display the original water temperature
(room temperature) in the kettle.
After 5s, the LCD will stop flashing and display 4.
the practical water temperature in the kettle.
The blue ON/OFF indicator will flash all the
time.

Содержание

Скачать