Home
Главная
Makita
Электрические Пилы
LH 1040
Инструкция по эксплуатации Страница: 15

Makita LH 1040 [15/60] Switch action fig 11

Adjusting the miter angle (Fig. 8)

Loosen the grip by turning counterclockwise. Turn the

turn base while pressing down the lock lever. When you

have moved the grip to the position where the pointer

points to the desired angle on the miter scale, securely

tighten the grip clockwise.

CAUTION:

• When turning the turn base, be sure to raise the handle

fully.

• After changing the miter angle, always secure the turn

base by tightening the grip firmly.

Adjusting the bevel angle (Fig. 9 & 10)

To adjust the bevel angle, loosen the lever at the rear of

the tool counterclockwise.

Push the handle to the left to tilt the saw blade until the

pointer points to the desired angle on the bevel scale.

Then tighten the lever clockwise firmly to secure the arm.

CAUTION:

• When tilting the saw blade, be sure to raise the handle

fully.

• After changing the bevel angle, always secure the arm

by tightening the lever clockwise.

Switch action (Fig. 11)

CAUTION:

• Before operation, make sure that the tool is turned on

and off.

To start the tool, press the ON ( I ) button. To stop it,

press the OFF ( O ) button.

Lighting up the lamps (Fig. 11 & 12)

For Model LH1040F only

Push the upper position of the switch for turning on the

light and the lower position for off.

CAUTION:

• Do not look in the light or see the source of light

directly.

NOTE:

• Use a dry cloth to wipe the dirt off the lens of lamp. Be

careful not to scratch the lens of light, or it may lower

the illumination.

Adjusting the level of top table (Fig. 13)

To adjust the level of top table, loosen two levers by turn-

ing counterclockwise and then raise or lower the top

table. Tighten these levers firmly after the adjustment.

WARNING:

• Position the top table at the topmost position when

using the tool in the miter saw mode and at the desired

position when using in the table saw mode (bench

mode).

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Installing or removing saw blade

CAUTION:

• Always be sure that the tool is switched off and

unplugged before installing or removing the blade.

• Use only the Makita socket wrench provided to install

or remove the blade. Failure to do so may result in

overtightening or insufficient tightening of the hex bolt.

This could cause an injury.

Secure the top table at the topmost position.

Lock the handle in the raised position by pushing in the

stopper pin. (Fig. 14)

To remove the blade, first loosen the clamping screw so

that the lower blade guard B is lowered as shown in the

figure. (Fig. 15)

Then use the socket wrench to loosen the hex bolt hold-

ing the center cover by turning it counterclockwise. Raise

the lower blade guard A and center cover while pushing

the lever nearby the handle to the left. (Fig. 16)

Press the shaft lock to lock the spindle and use the

socket wrench to loosen the hex bolt clockwise. Then

remove the hex bolt, outer flange and blade. (Fig. 17)

To install the blade, mount it carefully onto the spindle,

making sure that the direction of the arrow on the surface

of the blade matches the direction of the arrow on the

blade case. Install the outer flange and hex bolt, and then

use the socket wrench to tighten the hex bolt (left-

handed) securely counterclockwise while pressing the

shaft lock. (Fig. 18 & 19)

NOTE:

• When installing a saw blade, be sure to insert it from

the outside of the blade guard B at first and then raise it

so that the blade is finally placed in the blade guard B.

For all countries other than European countries

CAUTION:

• The silver ring 25.4 mm in outer diameter is factory-

installed onto the spindle. The black ring 25 mm in

outer diameter is included as standard equipment.

Before mounting the blade onto the spindle, always be

sure that the correct ring for the arbor hole of the blade

you intend to use is installed onto the spindle. (Fig. 20)

For European countries

CAUTION:

• The ring 30 mm in outer diameter is factory-installed

between the inner and outer flanges. (Fig. 20)

Return the lower blade guard A and center cover to its

original position. Then tighten the hex bolt clockwise to

secure the center cover. Raise the blade guard B as far

as it will go and tighten the clamping screw firmly while

holding it in the raised position. Lower the handle to

make sure that the lower blade guards move properly.

Make sure shaft lock has released spindle before making

cut.

Makita LH 1040 [15/60] Switch action fig 11

Содержание

Похожие устройства