Hitachi DA200E(S) Инструкция по эксплуатации онлайн [10/62] 2294
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Hitachi DA200E(S) Инструкция по эксплуатации онлайн [10/62] 2294

Hitachi DA200E(S) Инструкция по эксплуатации онлайн [10/62] 2294
GB-9
Fig. 3-5
Fig. 3-7B
Fig. 3-7Fig. 3-6
Fuel filter (Fig. 3-5)
Drain all fuel from fuel tank and pull fuel filter line
from tank. Pull filter element out of holder
assembly and rinse element in warm water with
detergent.
Rinse thoroughly until all traces of detergent are
eliminated. Squeeze, do not wring, away
excess water and allow element to air dry.
NOTE!
If element is hard due to excessive dirt buildup,
replace it.
Cleaning the cylinder fins (Fig. 3-6)
When wood chips are caught between cylinder
fins, the engine may overheat, resulting in
lower output. To avoid this, always keep
cylinder fins and fan case clean.
Every 100 Operating hours, or once a year
(more often if conditions require), clean fins and
external surfaces of engine of dust, dirt and oil
deposits which can contribute to improper
cooling.
Cleaning the muffler (Fig. 3-7, 7B)
Remove the muffler and spark arrestor (if so
equipped), and clean out any excess carbon
from the exhaust port or muffler inlet every 100
hours of operation.
For long-term storage
Drain all fuel from the fuel tank. Start and let
engine run until it stops. Repair any damage
which has resulted from use. Clean the unit
with a clean rag, or the use of high pressure air
hose. Put a few drops of two-cycle engine oil
into the cylinder through the spark plug hole,
and spin the engine over several times to
distribute oil. Cover the unit and store it in a dry
area.
Spark arrestor
If your unit comes with spark arrestor screen
and yet your local regulation requires use of
spark arrestor for prevention against a possible
fire, please attach it to the muffler by removing
muffler protector and other related parts (The
spark arrestor meets the regulation of SAE
J335-SEP90 and CSA CAN3-Z62. 1-M77)
Maintenance schedule
Below you will find some general maintenance
instructions. For further information please
contact HITACHI dealer.
Daily maintenance
Clean the exterior of the unit.
Check that the drilling attachment is properly
centred, sharp, and without cracks. An
offcentred bit induces heavy vibrations that
may damage the unit.
Chock that the drilling attachment is
sufficiently tightened.
Check that nuts and screws are sufficiently
tightened.
Weekly maintenance
Check the starter, especially cord and return
spring.
Clean the exterior of the spark plug.
Remove it and check the electrode gap.
Adjust it to 0.6 mm, or change the spark plug.
Clean the cooling fins on the cylinder and
check that the air intake at the starter is not
clogged.
Check that the gear case or transmission is
filled with grease up to 3/4.
Clean the air filter.
Monthly maintenance
Rinse the fuel tank with gasoline.
Clean the exterior of the carburetor and the
space around it.
Clean the fan and the space around it.

Содержание

Похожие устройства

030 Fig 3 5 Fig 3 6 Fig 3 7 Fig 3 7B Fuel filter Fig 3 5 Drain all fuel from fuel tank and pull fuel filter line from tank Pull filter element out of holder assembly and rinse element in warm water with detergent Rinse thoroughly until all traces of detergent are eliminated Squeeze do not wring away excess water and allow element to air dry NOTE If element is hard due to excessive dirt buildup replace it Cleaning the cylinder fins Fig 3 6 When wood chips are caught between cylinder fins the engine may overheat resulting in lower output To avoid this always keep cylinder fins and fan case clean Every 100 Operating hours or once a year more often if conditions require clean fins and external surfaces of engine of dust dirt and oil deposits which can contribute to improper cooling Cleaning the muffler Fig 3 7 7B Remove the muffler and spark arrestor if so equipped and clean out any excess carbon from the exhaust port or muffler inlet every 100 hours of operation Maintenance schedule Below you will find some general maintenance instructions For further information please contact HITACHI dealer Daily maintenance Clean the exterior of the unit Check that the drilling attachment is properly centred sharp and without cracks An offcentred bit induces heavy vibrations that may damage the unit Chock that the drilling attachment is sufficiently tightened Check that nuts and screws are sufficiently tightened For long term storage Drain all fuel from the fuel tank Start and let engine run until it stops Repair any damage which has resulted from use Clean the unit with a clean rag or the use of high pressure air hose Put a few drops of two cycle engine oil into the cylinder through the spark plug hole and spin the engine over several times to distribute oil Cover the unit and store it in a dry area Weekly maintenance Check the starter especially cord and return spring Clean the exterior of the spark plug Remove it and check the electrode gap Adjust it to 0 6 mm or change the spark plug Clean the cooling fins on the cylinder and check that the air intake at the starter is not clogged Check that the gear case or transmission is filled with grease up to 3 4 Clean the air filter Spark arrestor If your unit comes with spark arrestor screen and yet your local regulation requires use of spark arrestor for prevention against a possible fire please attach it to the muffler by removing muffler protector and other related parts The spark arrestor meets the regulation of SAE J335 SEP90 and CSACAN3 Z62 1 M77 Monthly maintenance Rinse the fuel tank with gasoline Clean the exterior of the carburetor and the space around it Clean the fan and the space around it GB 9

Скачать