Indesit ISL 70 C [11/96] Troubleshooting

Indesit ISL 70 C [11/96] Troubleshooting
11
Troubleshooting
GB
Problem:
The tumble dryer won’t start.
Drying cycle will not begin.
Its taking a long time to dry.
Empty water light is flashing
but the dryer has only been
running for a short period.
Empty water light is on and
the water container is not full.
The ON/OFF light flashes to
indicate a fault.
Programme finishes and
clothes are damper than
expected.
Possible causes / Solution:
The plug is not plugged into the socket, or not making contact.
There has been a power failure.
The fuse has blown. Try to plug another appliance into the socket.
You are using an extension cord? Try to plug the dryer’s power cord
directly into the socket.
The door is not closed securely?
The PROGRAMMES knob has not been set properly (see Start and
Programmes).
The START button has not been pressed (see Start and Programmes).
You have set a delayed time (see Start and Programmes).
The filter has not been cleaned (see Maintenance).
The water container needs emptying? The empty water light is flashing?
(see Maintenance).
The condenser needs cleaning? (see Maintenance).
The temperature setting is not ideal for the type of fabric you are drying
(see Start and Programmes, and see Laundry).
The correct drying time has not been selected for the load (see Laundry).
The air intake grille or rear vents are obstructed (see Installation, and see
Maintenance).
The items were too wet (see Laundry).
The dryer was overloaded (see Laundry).
The water container was probably not emptied at the start of the programme.
Do not wait for the empty water signal, always check and empty the
container before starting a new drying programme (see Maintenance).
This is normal, the light flashes when the container is full. If the light is on
but not flashing it is just a reminder to empty the container (see Start and
Programmes).
If the ON/OFF light flashes together with the Time Delay and High Heat
lights; Or the ON/OFF light flashes together with the Time Delay, Alarm,
High Heat and Empty Water lights, then:
- Turn off and remove the plug. Clean the filter and the condenser
(see Maintenance). Then replace the plug, turn on and start another
programme. If the same combination of lights still flash contact the
Service Centre (see Service).
If any other combination of lights flash: Note down the other lights that
are flashing and contact the Service Centre (see Service).
! For safety the dryer has a maximum programme time of 3 hours. If an
automatic programme has not sensed the required final moisture in this time
the dryer will complete the programme and stop. Check the above points
and run the programme again, if the results are still damp, contact the
Service Centre (see Service).
One day your dryer seems not to be working. Before you call your Service Centre (see Service), go through the
following troubleshooting suggestions:

Содержание

Troubleshooting QinoesiT One day your dryer seems not to be working Before you call your Service Centre see Service go through the following troubleshooting suggestions Problem Possible causes Solution The tumble dryer won t start The plug is not plugged into the socket or not making contact There has been a power failure The fuse has blown Try to plug another appliance into the socket You are using an extension cord Try to plug the dryer s power cord directly into the socket The door is not closed securely The PROGRAMMES knob has not been set properly see Start and Programmes The START button has not been pressed see Start and Programmes Drying cycle will not begin You have set a delayed time see Start and Programmes Its taking a long time to dry The filter has not been cleaned see Maintenance The water container needs emptying The empty water light is flashing GB see Maintenance The condenser needs cleaning see Maintenance The temperature setting is not ideal for the type of fabric you are drying see Start and Programmes and see Laundry The correct drying time has not been selected for the load see Laundry The air intake grille or rear vents are obstructed see Installation and see Maintenance The items were too wet see Laundry The dryer was overloaded see Laundry Empty water light is flashing but the dryer has only been running for a short period The water container was probably not emptied at the start of the programme Do not wait for the empty water signal always check and empty the container before starting a new drying programme see Maintenance Empty water light is on and the water container is not full This is normal the light flashes when the container is full If the light is on but not flashing it is just a reminder to empty the container see Start and Programmes The ON OFF light flashes to indicate a fault If the ON OFF light flashes together with the Time Delay and High Heat lights Or the ON OFF light flashes together with the Time Delay Alarm High Heat and Empty Water lights then Turn off and remove the plug Clean the filter and the condenser see Maintenance Then replace the plug turn on and start another programme If the same combination of lights still flash contact the Service Centre see Service If any other combination of lights flash Note down the other lights that are flashing and contact the Service Centre see Service Programme finishes and clothes are damper than expected For safety the dryer has a maximum programme time of 3 hours If an automatic programme has not sensed the required final moisture in this time the dryer will complete the programme and stop Check the above points and run the programme again if the results are still damp contact the Service Centre see Service 11