Zelmer Aquos ZVC722ST (829.0 ST) [58/60] End of operation cleaning and maintenance
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Zelmer Aquos ZVC722ST (829.0 ST) [58/60] End of operation cleaning and maintenance

Zelmer Aquos ZVC722ST (829.0 ST) [58/60] End of operation cleaning and maintenance
58
If the partition is not inserted properly, the
safetylockwillpreventcoveringthecontainer
withtheltrationunit.
●
Prepare the vacuum cleaner for operation according
to section B.
The vacuum cleaner starts up with default setting of the
highest power range. One diode will light on the power level
indicator (6). Set the desired power value (this function is
only available in vacuum cleaners type 829.0) by pressing
the power adjustment buttons , (5).
Do not operate the appliance for too long
without replacing the water in the container.
In case of long-term or very intensive
vacuumingoflargeamountsofdirt,thewater
inthetankwhichconstitutestherstltration
levelmayinwholeorinaconsiderablepartbe
absorbedbythedirt.Insuchacase,exchange
thewaterandcontinuevacuuming.
Avoid vacuuming surfaces covered with substances which
may favor an excessive foaming of the water inside the
tank. If you notice that the water is heavily foamed, add
a foam neutralizer recommended by the manufacturer of the
appliance e.g. “G 478 Buz
®
Defoam” in the amount indicated
on the packaging. It can be purchased in stores which offer
ZELMER products or by mail order.
Vacuumingwiththeamountofwaterinthetank
which exceeds the marked, permissible level
maycausethewatertospilltotheoutsideofthe
appliance.Ifthissituationrepeatsoften,itmay
leadtoafastcloggingoftheoutletEPAE10lter.
The vacuum cleaner is equipped with a oat
whichwillautomaticallyblockthesuctionifthe
foamlter II (10)isheavily dirty orthe liquid
exceeds the maximum level. In such a case
switchoffthevacuumcleanerbypressingthe
on/off button (1), unplug theappliance, clean
thelterandemptythecontainer.
PICKING UP WATER
If you want to use the vacuum cleaner to vacuum liquid, the
vacuum cleaner should be prepared as in the case of vacuum
cleaning with the use of the water lter module except that:
●
The container should be empty (without water).
●
You should use the nozzle for picking up water (20).
Donotoperatethevacuumcleanerwithafull
container! Do not vacuum large amounts of
liquid at a time (e.g. with the hose immersed
intowater).
If the water exceeds the maximum level during vacuuming,
the oat will automatically block the suction. The maximum
capacity of the container is about 4,0 l. In such a case proceed
in the manner described above in the part concerning the
blocking of suction caused by a dirty foam lter.
End of operation cleaning and maintenance
●
Switch off the vacuum cleaner by pressing the on/off
button (1) and unplug the appliance.
●
Wind the cord by pressing the cord rewind button (4).
While doing this hold the cord to make sure it is not
tangled and the plug does not hit the vacuum cleaner
housing.
●
Press the interlock on the hose end and remove the
hose from the opening.
●
Disconnect the telescopic tube from the hose and the
nozzle or brush.
●
In case of vacuuming or picking up water with the use
of the water lter module, remove the dirty water from
the tank.
●
It is recommended to wash the container, lters
(disassembly below) and partition thoroughly after each
use – changing water several times.
Ifyoudonotcleantheabove-mentionedparts
orcleantheminsufcientlyitmayleadtothe
lossoftheltrationcapabilitiesoftheinserts
andfoamandcausetheformationofbacteria
andmites.
Dry all the cleaned parts thoroughly before
reassembly.
Filter disassembly
FOAM FILTER I
1
Open the lid of the lter unit – press the handle and lift
the lid.
2
Take out the lter, wash it under running water, dry and
reinsert.
●
Close the lter unit lid by pressing it until you hear
a characteristic click.
FOAM FILTER II
It is recommended to wear rubber protective gloves while
dismantling the lter.
1
Grab the foam lter with your ngers and remove it from
the lter unit body.
2
Wash under running water, dry and reinsert.
Donothandwashthelterfoam,donotwring
it,donotwashitinwashingmachines.Avoid
crumpling, stretching and deforming. After
cleaning dry the foam in room temperature.
Neverdrythefoamonheaters,stoves,etc.
MOTOR FILTER
A ltration fabric is inserted in the motor cooling cycle which
is to catch the coal dust which arises due to the natural wear
and tear of the brushes and the commutator in the motor.
1
Remove the tank from the vacuum cleaner.
F
G
H

Содержание

Похожие устройства

Скачать