![D-Link DGS-1210-52/ME rev.B [181/519] Cable diagnostic port](/img/pdf.png)
D-Link DGS-1210-52/ME rev.B [181/519] Cable diagnostic port
![D-Link DGS-1210-28XS/ME [181/519] Cable diagnostic port](/views2/1459131/page181/bgb5.png)
DGS-1210/ME Metro Ethernet Switch CLI Reference Guide
163
Command: show syslog host
Host ID Host IP Address Severity Facility UDP Port Status
--------- ----------------------- ----------- ------------ ------------- -----------
1 1.1.2.1 All Local0 514 Enabled
Total Entries : 1
DGS-1210-28MP/ME:5#
cable diagnostic port
Purpose To determine if there are any errors on the copper cables and the
position where the errors may have occurred.
Syntax
cable diagnostic port [<portlist> | all]
Description
The cable diagnostic port command is used to determine if there
are any errors on the copper cables and the position where the
errors may have occurred.
Cable length is detected as following
range: <50m, 50~80, 80~100, >100m. Deviation is +/-
5 meters,
therefore "No Cable" may be displayed under "Test Result
," when
the cable used is less than 5 m in length. The Fault Distance will
show “No Cable”, whether the fiber is connected to the port or not.
Parameters
<portlist> – A port or range of ports to be configured.
all − Specifies all ports on the Switch are to be configured.
Restrictions None.
Example usage:
To determine the copper cables and position of port 3 on the Switch:
DGS-1210-28MP/ME:5# cable diagnostic port 15
Command: cable diagnostic port 15
Perform Cable Diagnostics ...
Port Type Link Status Test Result Cable Length (M)
------- ------- ------------------- ------------------------- ----------------------------
15 GE Link Up OK 4
DGS-1210-28MP/ME:5#
config syslogintimeout
Purpose To configure the system login timeout.
Syntax
config syslogintimeout <integer 3-30>
Description
The config syslogintimeout command is used to
configure the
system login timeout.
Содержание
- Cli reference guide 1
- Dgs 1210 me series 1
- Table of contents 2
- Introduction 19
- Using the console cli 21
- Command syntax 24
- Square brackets 24
- Vertical bar 24
- Braces 25
- Line editing key usage 25
- Multiple page display control keys 25
- Basic switch commands 26
- Command parameter 26
- Command parameter 27
- Enable password encryption 27
- Create account 28
- Disable password encryption 28
- Config account 29
- Delete account 30
- Reset account 30
- Show account 30
- Show session 31
- Show switch 31
- Show environment 32
- Enable jumbo_frame 33
- Show device_status 33
- Disable jumbo_frame 34
- Show jumbo_frame 34
- Show serial_port 34
- Config serial_port 35
- Config bootrom password 36
- Disable clipaging 36
- Enable clipaging 36
- Disable web 37
- Enable web 37
- Disable autoconfig 38
- Enable autoconfig 38
- Config autoconfig 39
- Show autoconfig 39
- Reboot 40
- Logout 42
- Reload config config_id 42
- Traceroute 45
- Show cpu port 46
- Traceroute6 46
- Reset cpu port 47
- Disable telnet 48
- Enable telnet 48
- Telnet 48
- Config time_range 49
- Show time_range 49
- Show tech support 50
- Clear tech support 52
- Command parameter 53
- Dhcp autoimage commands 53
- Disable autoimage 53
- Enable autoimage 53
- Show autoimage 54
- Command parameter 55
- Disable smtp 55
- Enable smtp 55
- Smtp server commands 55
- Config smtp 56
- Show smtp 56
- Smtp sent_testmsg 57
- Command parameter 59
- Config command_prompt 59
- Modify banner and prompt commands 59
- Config greeting_message 60
- Show greeting_message 61
- Command parameter 62
- Disable ddp 62
- Dlink discover protocol commands 62
- Enable ddp 62
- Config ddp report state 63
- Config ddp report timer 63
- Config ddp ports 64
- Show ddp 64
- Command parameter 66
- Config ports 66
- Switch port commands 66
- Config ports 67
- Show ports 68
- Show ports 69
- Delete ports 70
- Command parameter 71
- Disable loopdetect 71
- Enable loopdetect 71
- Loopback detection commands 71
- Config loopdetect mode 72
- Config loopdetect ports 72
- Config loopdetect 73
- Show loopdetect 73
- Command parameter 75
- Config dos_prevention dos_type 75
- Dos prevention commands 75
- Show dos_prevention 76
- Disable dos_prevention trap_log 77
- Enable dos_prevention trap_log 77
- Command parameter 78
- Config pppoe circuit_id_insertion state 78
- Pppoe circuit id insertion commands 78
- Config pppoe circuit_id_insertion ports 79
- Show pppoe circuit_id_insertion 79
- Show pppoe circuit_id_insertion ports 80
- Command parameter 81
- Dhcp server screening commands 81
- Command parameter 82
- Config filter dhcp_server 82
- Config filter dhcp_server log 83
- Show filter dhcp_server 83
- Show dhcp_server screening 84
- Config filter dhcpv6_server log 85
- Config filter dhcpv6_server ports 85
- Create filter dhcpv6_server permit_entry 85
- Delete filter dhcpv6_server permit_entry 86
- Show filter dhcpv6_server 86
- Config filter icmpv6_ra_all_node log 87
- Config filter icmpv6_ra_all_node ports 87
- Create filter icmpv6_ra_all_node permit_server 88
- Delete filter icmpv6_ra_all_node permit_server 88
- Show filter icmpv6_ra_all_node 89
- Command parameter 90
- Ip mac port binding commands 90
- Command parameter 91
- Create address_binding ip_mac 91
- Config address_binding ip_mac log 92
- Config address_binding ip_mac ports 92
- Config address_binding auto_scan 93
- Config address_binding auto_scan ipv6address 93
- Show address_binding ip_mac log 93
- Delete address_binding 94
- Show address_binding 95
- Disable address_binding dhcp_snoop 96
- Enable address_binding dhcp_snoop 96
- Show address_binding auto_scan list 96
- Config address_binding dhcp_snoop max_entry ports 97
- Show address_binding dhcp_snoop 97
- Disable address_binding dhcp_pd_snoop 98
- Enable address_binding dhcp_pd_snoop 98
- Config address_binding vlan 99
- Show address_binding dhcp_pd_snoop 99
- Disable address_binding roaming 100
- Enable address_binding roaming 100
- Show address_binding roaming 100
- Clear address_binding dhcp_snoop binding_entry ports 101
- Command parameter 102
- Network management snmp commands 102
- Command parameter 103
- Command parameter 104
- Command parameter 105
- Create snmp user 105
- Delete snmp user 106
- Create snmp view 107
- Show snmp user 107
- Delete snmp view 108
- Show snmp view 108
- Create snmp community 109
- Delete snmp all_community 110
- Delete snmp community 110
- Show snmp community 110
- Config snmp engineid 111
- Show snmp engineid 111
- Disable community_encryption 112
- Enable community_encryption 112
- Create snmp group 113
- Show community_encryption 113
- Delete snmp group 114
- Show snmp global state 115
- Show snmp groups 115
- Create snmp host 116
- Delete snmp host 117
- Show snmp host 117
- Create snmp v6host 118
- Delete snmp v6host 119
- Show snmp v6host 119
- Disable trusted_host 120
- Enable trusted_host 120
- Create trusted_host 121
- Delete trusted_host 122
- Show trusted_host 122
- Disable snmp traps 123
- Enable snmp traps 123
- Disable snmp authenticate_traps 124
- Enable snmp authenticate_traps 124
- Show snmp traps 124
- Disable snmp linkchange_traps 125
- Enable snmp linkchange_traps 125
- Config snmp linkchange_traps ports 126
- Show snmp traps linkchange_traps 126
- Config snmp system_contact 127
- Config snmp system_location 127
- Config snmp system_name 128
- Config snmp warmstart_traps 128
- Config snmp coldstart_traps 129
- Disable snmp 129
- Enable snmp 129
- Disable snmp dhcp_ screening traps 130
- Enable snmp dhcp_ screening traps 130
- Disable snmp dhcpv6_ screening traps 131
- Enable snmp dhcpv6_ screening traps 131
- Enable snmp icmpv6_ra_all_node traps 131
- Disable snmp icmpv6_ra_all_node traps 132
- Disable snmp impb_violation traps 132
- Enable snmp impb_violation traps 132
- Disable snmp firmware_upgrade_state traps 133
- Enable snmp firmware_upgrade_state traps 133
- Disable snmp lbd traps 134
- Enable snmp lbd traps 134
- Enable snmp port_security_violation traps 134
- Disable snmp port_security_violation traps 135
- Enable snmp rstpport_state_change traps 135
- Disable snmp duplicate_ip_detected traps 136
- Disable snmp rstpport_state_change traps 136
- Enable snmp duplicate_ip_detected traps 136
- Command parameter 138
- Download 138
- Download upload commands 138
- Download 139
- Upload 140
- Config configuration config_id 141
- Show firmware information 141
- Show config 142
- Config firmware image_id 143
- Show boot_file 143
- Show flash information 144
- Command parameter 145
- Dhcp relay commands 145
- Command parameter 146
- Disable dhcp_relay 146
- Enable dhcp_relay 146
- Config dhcp_relay add ipif system 147
- Config dhcp_relay port 147
- Config dhcp_relay delete ipif system 148
- Config dhcp_relay hops 148
- Config dhcp_relay option_82 149
- Config dhcp_relay vlan 149
- Config dhcp_relay port_option_82 151
- Show dhcp_relay port_option_82 151
- Enable dhcp_local_relay 152
- Show dhcp_relay 152
- Config dhcp_local_relay port 153
- Disable dhcp_local_relay 153
- Config dhcp_local_relay vlan 154
- Show dhcp_local_relay 154
- Disable dhcpv6_relay 155
- Enable dhcpv6_relay 155
- Show dhcpv6_relay 155
- Config dhcpv6_relay 156
- Config dhcpv6_relay hop_count 157
- Config dhcpv6_relay option_18 157
- Config dhcpv6_relay option_37 158
- Config dhcpv6_relay option_38 158
- Show dhcpv6_relay option_38 159
- Command parameter 160
- Config gratuitous_arp send ipif_status_up 160
- Gratuitous arp commands 160
- Config gratuitous_arp learning 161
- Config gratuitous_arp send dup_ip_detected 161
- Disable gratuitous_arp log 162
- Enable gratuitous_arp log 162
- Config gratuitous_arp log 163
- Show gratuitous_arp 163
- Config gratuitous_arp send periodically ipif 164
- Command parameter 165
- Config power_saving 165
- Config power_saving mode 165
- Power saving commands 165
- Show power_saving 166
- Command parameter 167
- Cpu protection commands 167
- Disable cpu_protect 167
- Enable cpu_protect 167
- Config cpu_protect type 168
- Show cpu_protect 168
- Command parameter 170
- Network monitoring commands 170
- Show packet ports 170
- Show error ports 171
- Show utilization 172
- Clear counters 173
- Clear log 173
- Save log 173
- Enable syslog 174
- Show log 174
- Disable syslog 175
- Show syslog 175
- Create syslog host 176
- Config syslog host 178
- Delete syslog host 180
- Show syslog host 180
- Cable diagnostic port 181
- Config syslogintimeout 181
- Config sysgroupinterval 182
- Show log_software_module 182
- Command parameter 184
- Config poe ports 184
- Poe commands 184
- Config poe system 185
- Show poe ports 185
- Show poe system 186
- Command parameter 188
- Config stp 188
- Spanning tree commands 188
- Config stp ports 189
- Config stp fbpdu 191
- Config stp version 191
- Config stp priority 192
- Disable stp 192
- Enable stp 192
- Show stp 193
- Show stp ports 194
- Show stp instance 195
- Create stp instance_id 196
- Show stp mst_config_id 196
- Config stp instance_id 197
- Delete stp instance_id 197
- Config stp mst_config_id 198
- Config stp mst_ports 198
- Config stp trap 199
- Command parameter 201
- Create fdb 201
- Forwarding database commands 201
- Config fdb aging_time 202
- Delete fdb 202
- Config flood_fdb 203
- Disable flood_fdb 203
- Enable flood_fdb 203
- Clear flood_fdb 204
- Show flood_fdb 204
- Show fdb 205
- Clear fdb 206
- Config multicast vlan_filtering_mode 206
- Config multicast_filtering_mode 207
- Delete auto_fdb 207
- Broadcast storm control commands 208
- Command parameter 208
- Config traffic control 208
- Config traffic control auto_recover_time 209
- Show traffic control 209
- Config traffic trap 210
- Command parameter 211
- Disable password_recovery 211
- Enable password_recovery 211
- Password recovery commands 211
- Show password_recovery 212
- Command parameter 213
- Qos commands 213
- Command parameter 214
- Config scheduling 215
- Show scheduling 215
- Config bandwidth_control 216
- Config cos mac_mapping 217
- Show bandwidth_control 217
- Delete cos mac_mapping 218
- Show cos mac_mapping 218
- Config cos ip_mapping 219
- Show cos ip_mapping 219
- Config cos ipv6_mapping 220
- Delete cos ip_mapping 220
- Show cos ipv6_mapping 220
- Config cos ipv6_tc_mapping 221
- Delete cos ipv6_mapping 221
- Delete cos ipv6_tc_mapping 222
- Show cos ipv6_tc_mapping 222
- Config cos mapping 223
- Show cos mapping 223
- Config cos protocol_mapping 224
- Show cos protocol_mapping 224
- Config cos vlanid_mapping 225
- Delete cos protocol_mapping 225
- Show cos vlanid_mapping 225
- Config cos tos value 226
- Delete cos vlanid_mapping 226
- Config cos tcp_port_mapping 227
- Show cos tos 227
- Delete cos tcp_port_mapping 228
- Show cos tcp_port_mapping 228
- Config cos udp_port_mapping 229
- Show cos udp _port_mapping 229
- Config 802 p user_priority 230
- Delete cos udp_port_mapping 230
- Config 802 p default_priority 231
- Show 802 p user_priority 231
- Config scheduling_mechanism 232
- Show 802 p default_priority 232
- Show scheduling_mechanism 233
- Config dscp tos mode 234
- Config dscp_mapping 234
- Enable hol_prevention 235
- Show dscp_mapping 235
- Disable hol_prevention 236
- Show hol_prevention 236
- Command parameter 237
- Config reboot schedule 237
- Reboot schedule commands 237
- Delete reboot schedule 238
- Show reboot schedule 238
- Command parameter 240
- Enable rmon 240
- Rmon commands 240
- Create rmon alarm 241
- Disable rmon 241
- Delete rmon alarm 242
- Show rmon alarm 242
- Create rmon collection stats 243
- Create rmon collection history 244
- Delete rmon collection stats 244
- Create rmon event 245
- Delete rmon collection history 245
- Delete rmon event 246
- Show rmon 246
- Show rmon statistics 246
- Command parameter 248
- Disable mirror 248
- Enable mirror 248
- Port mirroring commands 248
- Config mirror target 249
- Show mirror 250
- Erps commands 251
- Enable erps 252
- Config erps raps_vlan ring_mel 253
- Create erps raps_vlan 253
- Disable erps 253
- Config erps raps_vlan ring_port 254
- Config erps raps_vlan rpl 255
- Config erps raps_vlan protected_vlan 256
- Config erps raps_vlan timer 256
- Config erps raps_vlan state 257
- Config erps raps_vlan sub_ring 258
- Config erps raps_vlan revertive 259
- Config erps raps_vlan tc_propagation 259
- Delete erps raps_vlan 260
- Show erps 260
- Config erps log 261
- Config erps ring ring_id 262
- Config erps trap 262
- Create erps ring 262
- Config erps ring instance 263
- Config erps ring ring_type 263
- Config erps ring ring_port 264
- Config erps instance state 265
- Delete erps ring 265
- Show erps ring 265
- Config erps instance sub_ring_instance 266
- Config erps instance raps_vlan 267
- Config erps instance tc_propagation 267
- Config erps instance mel 268
- Config erps instance protected_vlan 269
- Config erps instance rpl 269
- Config erps instance timer 270
- Config erps instance revertive mode 271
- Erps clear instance 272
- Show erps instance 272
- Erps force switch instance 273
- Erps manual switch instance 273
- Config erps version 274
- Command parameter 275
- Vlan commands 275
- Command parameter 276
- Create vlan 276
- Config vlan 277
- Delete vlan 277
- Config private_vlan 278
- Config private_vlan trunk 279
- Config gvrp 280
- Show private_vlan 280
- Config gvrp timer 281
- Enable gvrp 281
- Disable gvrp 282
- Show vlan 282
- Config dot1v_protocol_group 283
- Create dot1v_protocol_group 283
- Delete dot1v_protocol_group 284
- Show dot1v_protocol_group 284
- Config port dot1v ports 285
- Show gvrp 286
- Show port dot1v 286
- Enable vlan_trunk 287
- Show gvrp timer 287
- Config vlan_trunk ports 288
- Disable vlan_trunk 288
- Show vlan_trunk 288
- Disable asymmetric_vlan 289
- Enable asymmetric_vlan 289
- Disalbe pvid auto_assign 290
- Enable pvid auto_assign 290
- Show asymmetric_vlan 290
- Create mac_based_vlan mac_address 291
- Show pvid auto_assign 291
- Deleete mac_based_vlan mac address 292
- Show mac_based_vlan mac address 292
- Config vlan_auto_learn 293
- Show vlan_auto_learn 293
- Command parameter 295
- Mac based access control commands 295
- Config mac_based_access_control password 296
- Disable mac_based_access_control 296
- Enable mac_based_access_control 296
- Config mac_based_access_control method 297
- Config mac_based_access_control port 297
- Config mac_based_access_control log state 298
- Config mac_based_access_control trap state 298
- Config mac_based_access_control log max_users 299
- Create mac_based_access_control_local mac_address 299
- Show mac_based_access_control 300
- Show mac_based_access_control_local 300
- Delete mac_based_access_control_local 301
- Show mac_based_access_control auth_state ports 301
- Command parameter 303
- Enable qinq 303
- Q in q commands 303
- Disable qinq 304
- Show qinq 304
- Config qinq inner_tpid 305
- Config qinq ports 305
- Create vlan_translation 306
- Show vlan_translation 306
- Delete vlan_translation ports 307
- Command parameter 308
- Create link_aggregation 308
- Link aggregation commands 308
- Config link_aggregation group_id 309
- Delete link_aggregation 309
- Config link_aggregation algorithm 310
- Config link_aggregation state 310
- Show link_aggregation 311
- Basic ip commands 312
- Command parameter 312
- Create ipif 312
- Delete ipif 313
- Disable ipif 313
- Enable ipif 313
- Config ipif 314
- Bpdu attack protection commands 316
- Command parameter 316
- Config bpdu_protection ports 316
- Config bpdu_protection recovery_timer 317
- Config bpdu_protection 318
- Enable bpdu_protection 318
- Disable bpdu_protection 319
- Show bpdu_protection 319
- Command parameter 321
- Create mac_protection 321
- Delete mac_protection 321
- Mac protection commands 321
- Show mac_protection 322
- Command parameter 323
- Config ethernet_oam ports 323
- Ethernet oam commands 323
- Config ethernet_oam ports 324
- Show ethernet_oam ports 325
- Show ethernet_oam ports 326
- Show ethernet_oam ports 327
- Show ethernet_oam ports 328
- Clear ethernet_oam ports 329
- Command parameter 330
- Disable mac_notification 330
- Enable mac_notification 330
- Mac notification commands 330
- Config mac_notification 331
- Config mac_notification ports 331
- Show mac_notification 332
- Show mac_notification ports 332
- Command parameter 334
- Igmp snooping commands 334
- Command parameter 335
- Config igmp_snooping 335
- Config igmp_snooping querier 336
- Config igmp_snooping multicast_vlan 337
- Create igmp_snooping multicast_vlan 337
- Config igmp_snooping multicast_vlan_group 338
- Delete igmp_snooping multicast_vlan 338
- Create igmp_snooping static_group 339
- Config igmp_snooping static_group 340
- Delete igmp_snooping static_group 340
- Config igmp_snooping data_driven_learning 341
- Show igmp_snooping static_group 341
- Config igmp_snooping data_driven_learning 342
- Clear igmp_snooping data_driven_group 343
- Config router_ports 343
- Config router_ports_forbidden 344
- Config igmp access_authentication ports 345
- Show igmp access_authentication ports 345
- Disable igmp_snooping 346
- Enable igmp_snooping 346
- Show igmp_snooping 347
- Show igmp_snooping group 347
- Show igmp_snooping forwarding 348
- Show igmp_snooping host 349
- Show igmp_snooping multicast_vlan 349
- Show igmp_snooping multicast_vlan_group 350
- Show igmp_snooping statistic counter 350
- Clear igmp_snooping statistic counter 351
- Show router_ports 351
- Command parameter 353
- Create iproute 353
- Ipv4 ipv6 routing commands 353
- Delete iproute 354
- Show iproute 354
- Create ipv6route 355
- Delete ipv6route 355
- Show ipv6route 356
- Command parameter 357
- Disable l2protocol_tunnel 357
- Enable l2protocol_tunnel 357
- Layer 2 protocol tunneling commands 357
- Config l2protocol_tunnel ports 358
- Show l2protocol_tunnel 358
- Command parameter 360
- Config ddm ports 360
- Digital diagnostic monitoring commands 360
- Config ddm power_unit 361
- Show ddm ports 361
- Command parameter 363
- Mld snooping commands 363
- Command parameter 364
- Disable mld_snooping 364
- Enable mld_snooping 364
- Config mld_snooping 365
- Config mld_snooping multicast_vlan 366
- Create mld_snooping multicast_vlan 366
- Delete mld_snooping multicast_vlan 367
- Show mld_snooping multicast_vlan 367
- Config mld_snooping multicast_vlan_group 368
- Show mld_snooping multicast_vlan_group 368
- Config mld_snooping mrouter_ports 369
- Config mld_snooping mrouter_ports_forbidden 369
- Config mld_snooping querier 370
- Config mld_snooping data_driven_learning 371
- Clear mld_snooping data_driven_group 372
- Show mld_snooping 372
- Show mld_snooping forwarding 373
- Show mld_snooping group 374
- Show mld_snooping mrouter_ports 374
- Show mld_snooping host 375
- Clear mld_snooping statistics counter 376
- Show mld_snooping statistics counter 376
- Command parameter 377
- Create mcast_filter_profile 377
- Limited ip multicast address commands 377
- Config mcast_filter_profile profile_id 378
- Config mcast_filter_profile profile_name 378
- Config mcast_filter_profile ipv6 379
- Delete mcast_filter_profile 379
- Show mcast_filter_profile 380
- Config limited_multicast_addr 381
- Show limited_multicast_addr 381
- Config max_mcast_group 382
- Show max_mcast_group 382
- Command parameter 384
- X commands 384
- Command parameter 385
- Disable 802 x 385
- Enable 802 x 385
- Show 802 x 386
- Show 802 x auth_state 386
- Show 802 x auth_configuration 387
- Config 802 x auth_parameter ports 388
- Config 802 x init 389
- Config 802 x auth_protocol 390
- Config 802 x reauth 390
- Config radius add 391
- Config radius 392
- Config radius delete 392
- Config 802 x fwd_pdu system 393
- Show radius 393
- Config 802 x auth_mode 394
- Show 802 x fwd_pdu system status 394
- Create 802 x guest_vlan 395
- Delete 802 x guest_vlan 395
- Config 802 x guest_vlan ports 396
- Show 802 x guest_vlan 396
- Create 802 x user 397
- Show 802 x user 397
- Config 802 x capability ports 398
- Delete 802 x user 398
- Command parameter 400
- Config port_security 400
- Port security commands 400
- Show port_security 401
- Clear port_security _entry 402
- Delete port_security _entry 402
- Command parameter 403
- Config sntp 403
- Time and sntp commands 403
- Enable sntp 404
- Show sntp 404
- Config time 405
- Disable sntp 405
- Config dst 406
- Config time_zone operator 406
- Show time 407
- Arp commands 409
- Command parameter 409
- Config arp_aging time 409
- Clear arptable 410
- Create arpentry 410
- Config arpentry 411
- Delete arpentry 411
- Show arpentry 412
- Show arpentry aging_time 412
- Command parameter 413
- Enable rspan 413
- Remote switched port analyzer commands 413
- Create rspan vlan 414
- Disable rspan 414
- Config rspan vlan 415
- Delete rspan vlan 416
- Show rspan 416
- Command parameter 417
- Sflow commands 417
- Disable sflow 418
- Enable sflow 418
- Show sflow 418
- Create sflow flow_sampler ports 419
- Config sflow flow_sampler ports 420
- Delete sflow flow_sampler ports 420
- Show sflow flow_sampler 421
- Create sflow analyzer_server 422
- Config sflow analyzer_server 423
- Delete sflow analyzer_server 423
- Show sflow analyzer_server 424
- Config sflow counter_poller ports 425
- Create sflow counter_poller ports 425
- Delete sflow counter_poller ports 426
- Show sflow counter_poller 426
- Command parameter 428
- Commands 428
- Config duld ports 428
- D link unidirectional link detection duld 428
- D link unidirectional link detection duld commands 428
- Config duld recover_timer 429
- Show duld ports 429
- Show duld recover_timer 430
- Command parameter 431
- Create ipv6 neighbor_cache 431
- Ipv6 neighbor discovery commands 431
- Delete ipv6 neighbor_cache 432
- Show ipv6 neighbor_cache 432
- Config ipv6 nd ns ipif 433
- Show ipv6 nd 433
- Disable ipif_ipv6_link_local_auto 434
- Enable ipif_ipv6_link_local_auto 434
- Banner commands 436
- Command parameter 436
- Config log_save_timing 436
- Show log 437
- Show log_save_timing 437
- Command history list commands 438
- Command parameter 438
- Show command_history 439
- Command logging commands 441
- Command parameter 441
- Disable command logging 441
- Enable command logging 441
- Show command logging 442
- Command parameter 443
- Enable ssh 443
- Ssh commands 443
- Config ssh algorithm 444
- Disable ssh 444
- Config ssh authmode 445
- Show ssh authmode 445
- Config ssh server 446
- Show ssh server 446
- Config ssh user 447
- Show ssh algorithm 447
- Show ssh user authmode 448
- Command parameter 449
- Enable ssl 449
- Ssl commands 449
- Disable ssl 450
- Show ssl 450
- Download ssl certificate 451
- Access authentication control commands 452
- Command parameter 452
- Command parameter 453
- Create authen_login method_list_name 453
- Config authen_login 454
- Delete authen_login method_list_name 455
- Show authen_login 455
- Show authen_policy 456
- Config authen_enable 457
- Create authen_enable method_list_name 457
- Delete authen_enable method_list_name 459
- Show authen_enable 459
- Disable authen_policy 460
- Enable authen_policy 460
- Config authen application 461
- Show authen application 461
- Config authen parameter 462
- Create authen server_host 463
- Show authen parameter 463
- Config authen server_host 464
- Delete authen server_host 465
- Show authen server_host 466
- Config authen server_group 467
- Create authen server_group 467
- Delete authen server_group 468
- Show authen server_group 468
- Enable admin 469
- Config accounting 470
- Config admin local_enable 470
- Config accounting service 471
- Config accounting service command 472
- Create accounting method_list_name 472
- Delete accounting method_list_name 473
- Show accounting method_list_name 473
- Disable aaa_server_password_encryption 474
- Enable aaa_server_password_encryption 474
- Show aaa 475
- Command parameter 476
- Config eee port 476
- Energy efficient ethernet commands 476
- Show eee_mode port 476
- Command parameter 478
- Config lacp port_priority 478
- Lacp commands 478
- Show lacp 478
- Config lacp_ports 479
- Command parameter 481
- Lldp commands 481
- Config lldp message_tx_interval 482
- Disable lldp 482
- Enable lldp 482
- Config lldp message_tx_hold_multiplier 483
- Config lldp reinit_delay 483
- Config lldp notification_interval 484
- Config lldp tx_delay 484
- Show lldp 485
- Show lldp ports 485
- Show lldp local_ports 486
- Config lldp ports 487
- Show lldp remote_ports 487
- Config lldp ports 488
- Config lldp ports 489
- Config lldp ports 490
- Config lldp ports 491
- Show lldp mgt_addr 491
- Show lldp power_pse_tlv 492
- Show lldp statistics 492
- Access control list commands 493
- Command parameter 493
- Command parameter 494
- Create access_profile 494
- Config access_profile 496
- Delete access_profile 500
- Show access_profile 500
- Create cpu_access_profile 501
- Config cpu_access_profile 503
- Delete cpu_access_profile 504
- Enable cpu_interface_filtering 505
- Show cpu_access_profile 505
- Config flow_meter profile_id 506
- Disable cpu_interface_filtering 506
- Show flow_meter 507
- Command parameter 508
- Config traffic_segmentation 508
- Show traffic_segmentation 508
- Traffic segmentation commands 508
- Command parameter 510
- Config safeguard_engine 510
- Safeguard commands 510
- Show safeguard_engine 510
- Device specifications 512
- Technical specifications 512
- Supported transceivers 518
Похожие устройства
- D-Link DGS-1210-52/ME rev.B Краткое руководство по установке
- D-Link DGS-1210-52/ME rev.B Руководство пользователя _Web UI_
- D-Link DGS-1210-52/ME rev.A Руководство по установке
- D-Link DGS-1210-52/ME rev.A Руководство пользователя _Web UI_
- D-Link DGS-1210-52/ME rev.A Руководство пользователя _CLI_
- D-Link DGS-1210-52MPP/ME Краткое руководство по установке
- D-Link DGS-1210-52P/ME Краткое руководство по установке
- D-Link DGS-1510-10L/ME Руководство пользователя _Web UI_
- D-Link DGS-1510-10L/ME Руководство пользователя _CLI_
- D-Link DGS-1510-10L/ME Руководство по установке
- D-Link DGS-1510-10L/ME Краткое руководство по установке
- D-Link DGS-1510-28LP/ME Руководство по установке
- D-Link DGS-1510-28LP/ME Руководство пользователя _CLI_
- D-Link DGS-1510-28LP/ME Краткое руководство по установке
- D-Link DGS-1510-28LP/ME Руководство пользователя _Web UI_
- D-Link DGS-1510-28XMP/ME Руководство пользователя _CLI_
- D-Link DGS-1510-28XMP/ME Руководство пользователя _Web UI_
- D-Link DGS-1510-28XMP/ME Руководство по установке
- D-Link DGS-1510-28XMP/ME Краткое руководство по установке
- D-Link DGS-1510-52L/ME Руководство по установке
Скачать
Случайные обсуждения
Ответы 1
Какой IP-адрес должен быть назначен компьютеру для входа в Web-интерфейс коммутатора?
2 года назад