Home
Главная
IVT
Лобзик
JS-400
Инструкция по эксплуатации Страница: 8

IVT JS-400 [8/56] Instruction manual

Instruction manual

CAUTION! The appliance should

always be switched off at the mains

before disconnecting any plug and

socket connector or extension cables.

∙ Never pass the appliance over its own cord or

extension cable, while the tool is working. Make sure

you always know where the cable is.

∙ Do not wire a power cable directly into your device

yourself. Instead, take the device to your nearest

authorized Service Center.

∙ To avoid danger, damaged power cord should

be replaced by manufacturer or its agent, or similar

qualied person.

∙ Immediately unplug the tool when its cable is

damaged or cut.

ATTENTION! DANGER OF ELECTRIC

SHOCK!

Consider working area environment. Do not expose

power tools to rain. Do not use power tools in damp

or wet locations. Keep work area well lit and dry. Try

to prevent the device from getting wet or being

exposed to humidity. Do not leave it outside

overnight. Water entering a power tool will increase

the risk of electric shock.

∙ The power supply cable should be checked

regularly and, before using it, make sure the cable is

not damaged or worn out. If the cable is not in good

condition, do not use the appliance; take it to an

authorized service Center.

∙ When tool is used outdoor, only use an extension

cable that is suitable for outdoor use and which is

marked for this specic use. Keep it away from the

working area, from damp, wet or oily surfaces and away

from heat and ammable materials.

∙ Avoid any accidental starting: make sure that the

power switch (if present) is in the «off» position, before

plugging the tool in.

∙ Remove adjusting keys or wrenches before turning

the tool on.

∙ Do not use the tool if the switch does not turn the

tool on or off. Any tool that cannot be controlled with the

switch is dangerous and must be repaired.

WARNING! During the use of certain

power tools, some dust containing

chemicals known to cause cancer,

may occur.

Some of these chemicals are: lead from lead based

paints, crystalline silica from bricks and cement and other

masonry products, arsenic and chromium from chemically

treated lumber and other dangerous products. If dust is

present, your risk from these exposures varies,

depending on how often you do this type of work. To

reduce your exposure to these chemicals, any time

you do pulverulent operations, work in a well

ventilated area and work with approved safety

equipment, such as dust masks that are specially

designed to lter out microscopic particles.

∙ If the appliance strikes a foreign body, examine the

device for signs of damage and carry out any necessary

repairs before restarting and continuing to work.

∙ If the appliance starts to vibrate abnormally, turn

it off and check for the cause immediately. Vibration is

generally a warning of trouble.

∙ Always switch off the appliance and wait until

the device completely stops whenever you leave

the machine, before carrying out maintenance,

before changing accessories, checking, cleaning,

troubleshooting or working on the appliance.

∙ It is forbidden to move or modify any of the internal

parts of the device.

Specic safety rules

∙ Never cut materials containing asbestos because

they may generate dust dangerous to your health.

∙ To reduce your exposure to harmful chemicals that

may be content in materials you’re working on: work in

a well ventilated area and work with approved safety

equipment, such as dust masks that are specially

designed to lter out microscopic particles. Connect a

dust extraction device to the tool.

∙ Use clamps or other practical way to secure and

support the workpiece to a stable platform. Holding the

work by hand or against your body is unstable and may

lead to loss of control. Don’t work on any workpiece that

is too small to clamp in place.

∙ Never cut or saw in concealed areas where there

may be electric gas, or water lines. Use a suitable

detector to nd such lines.

∙ Keep the cutting path free of obstacles, both above

and below.

∙ Be aware of the location and setting of the lock-on

button. If the switch is locked “ON” during the use, be

ready for emergency situations to switch it “OFF”, by

rst pulling the on-off switch then immediately releasing

it without pressing the lock-on button.

∙ The base plate must rest securely on its entire

surface.

∙ When working, never move your hand or nger

ahead of the saw blade.

∙ Tool can chatter or vibrate if blade speed is too slow

at beginning of cut and possibly kickback.

∙ Always pull out the mains plug before changing the

IVT JS-400 [8/56] Instruction manual

Содержание

Похожие устройства