Candy PMI 640 N [6/32] Cleaning and maintenance
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Candy PMI 640 N [6/32] Cleaning and maintenance

Candy PMI 640 N [6/32] Cleaning and maintenance
5 GB
• RESIDUAL HEAT INDICATOR
The control panel tells the user when the surface temperature of
the cooking zones exceeds about 60°C, by the following displaying:
. When the temperature goes back below 60°C, the display
goes off.
For ending the cooking, we advise switching off the cooking zone
and using the residual heat of the zone to finish cooking gently.
N.B. After a cut in the current, the residual heat indicator disappears
completely, even if the surface temperature exceeds 60°C.
• PAN DETECTOR (induction models)
When the hob is operating, the pan detector provides the
advantage of automatically stopping or starting the heat of the
cooking zone in contact with or on removal of the pan.
If therefore offers energy savings.
If the cooking zone is used with a suitable pan* : the display
shows the heat level or when the booster is operating.
* The induction needs pans compatibles so fitted with magnetic-
bottomed, see table page 9 and pans big enough to fully cover
the zone.
If the cooking zone is used without a pan or with an unsuitable
pan : the display shows . The zone does not start. If no pan
is detected after 10 minutes, the starting operation is cancelled.
IMPORTANT:
To stop the cooking zone, you must stop the hob normally,
you cannot just remove the pan. The pan detector does not
work as the hob on/off button.
• PROGRAMMING A COOKING ZONE
Every cooking zone can be programmed for a maximum time of
99 minutes. Only one zone, at a time, can be programmed.
- Start the required zone by following the previous instructions.
The control LED near the heat level must be displayed, it shows
that the zone is live.
- Press the Timer button.
The zone mark around the timer display shows the controlled
zone.
- Press the button or to select the time in minutes.
This is saved automatically after three seconds.
The programmed time can be modified at any moment by pressing
the timer selection button, the timer control LED must be on.
When the time has run, the cooking zone goes off automatically
and an audible beep sounds for 1 minute. Press any button to
stop it.
The programmed time can be reset to using the button
or pressing the and buttons at the same time, the cooking
zone is then no longer linked to the timer but stays operational.
So you will have to stop the zone independently.
The timer can be used alone as a reminder, it will ring at the end
of the programmed time.
MAINTENANCE:
- Place a few drops of the specialised cleaning product on the
hob surface.
- Rub any stubborn stains with a soft cloth or with slightly damp
kitchen paper.
- Wipe with a soft cloth or dry kitchen paper until the surface is
clean.
If there are still some stubborn stains:
- Place a few more drops of specialised cleaning fluid on the
surface.
- Scrape with a scraper, holding it at an angle of 30° to the hob,
until the stains disappear.
- Wipe with a soft cloth or dry kitchen paper until the surface is
clean.
- Repeat the operation if necessary.
A FEW HINTS:
Frequent cleaning leaves a protective layer which is essential to
prevent scratches and wear. Make sure that the surface is clean
before using the hob again. To remove marks left by water, use
a few drops of white vinegar or lemon juice. Then wipe with
absorbent paper and a few drops of specialised cleaning fluid.
The glass ceramic surface will withstand scraping from flat-
bottomed cooking vessels, however, it is always better to lift them
when moving them from one zone to another.
NB:
Do not use a sponge which is too wet.
Never use a knife or a screwdriver.
A scraper with a razor blade will not damage the surface, as
long as it is kept at an angle of 30°.
Never leave a scraper with a razor blade within the reach of
children.
Never use abrasive products or scouring powders.
30° Maxi
• Before carrying out any maintenance work on the hob, allow it
to cool down.
• Only products, (creams and scrapers) specifically designed for
glass ceramic surfaces should be used. They are obtainable
from hardware stores.
• Avoid spillages, as anything which falls on to the hob surface
will quickly burn and will make cleaning more difficult.
• It is advisable to keep away from the hob all substances which
are liable to melt, such as plastic items, sugar, or sugar-based
products.
CLEANING AND MAINTENANCE
The locking function prevents anyone from starting the hob. It is
also used for cleaning the control strip as the controls can be
locked without the hob being on.
• LOCKING BUTTON OPERATION
To lock the hob :
- Press the on/off button .
- Press simultaneously " - " button and " + " button of the front
right zone, and then press again on the " + " button of this zone.
The hob is locked, the locking indicator " L " is displayed on all
zones for 20 seconds.
To unlock the hob :
- Press the on/off button . The locking indicator " L " is displayed
on all zones.
-Press simultaneously the " - " button and the " + " button of the
front right zone, and then press again on the " - " button of this
zone. The hob is unlocked.

Содержание

Похожие устройства

Скачать