Fiat LINEA [134/233] Warning

Fiat LINEA [134/233] Warning
134
ПРИБОРЫ
И ОРГАНЫ
УПРАВЛЕНИЯ
КОНТРОЛЬНЫЕ
ЛАМПЫ И
СООБЩЕНИЯ
СИСТЕМА БЕЗО-
ПАСНОСТИ
СОВЕТЫ
ВОДИТЕЛЮ
АВТОМОБИЛЯ
УСТРАНЕНИЕ
НЕИСПРАВ-НОСТЕЙ
ТЕХНИЧЕСКОЕ
ОБСЛУЖИВАНИЕ
ТЕХНИЧЕСКИЕ
ХАРАКТЕРИСТИКИ
ПРЕДМЕТНЫЙ
УКАЗАТЕЛЬ
130
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
Assembly diagram fig. 3
The tow hook structure must be fastened
in the points shown by the symbol
Ø
us-
ing a total of 6 M8 screws and 2 M10
screws.
The internal back plates are to be at least
6 mm thick.
The hook should be fastened to the body
avoiding any type of drilling and trimming
of the rear bumpers that remains visible
when the hook is removed.
IMPORTANT It is compulsory to fasten a
label (plainly visible) of suitable size and
material with the following wording:
MAX LOAD ON BALL 70 kg
After fitting, screw holes
shall be sealed to prevent ex-
haust gas inlet.
WARNING
fig. 3
F0R0190m
Existing hole
Existing screw
To load
Existing screw
Existing screw
Existing screw
Existing screw
Existing hole
Type-approved ball
СБОРОЧНАЯ СХЕМА (рис.3)
Для крепления прицепного устройства в
точках, отмеченных на схеме символом
130
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
Assembly diagram fig. 3
The tow hook structure must be fastened
in the points shown by the symbol
Ø
us-
ing a total of 6 M8 screws and 2 M10
screws.
The internal back plates are to be at least
6 mm thick.
The hook should be fastened to the body
avoiding any type of drilling and trimming
of the rear bumpers that remains visible
when the hook is removed.
IMPORTANT It is compulsory to fasten a
label (plainly visible) of suitable size and
material with the following wording:
MAX LOAD ON BALL 70 kg
After fitting, screw holes
shall be sealed to prevent ex-
haust gas inlet.
WARNING
fig. 3
F0R0190m
Existing hole
Existing screw
To load
Existing screw
Existing screw
Existing screw
Existing screw
Existing hole
Type-approved ball
, используется в общей сложности 6
болтов M8 и 2 винта типа MIO.
Толщина внутренних крепежных пластин
должна быть не менее 6 мм.
Тягово-сцепное устройство должно быть
закреплено на кузове автомобиля без
применения операций, связанных со
сверлением и механической обработкой
заднего бампера, последствия которых
будут заметны после снятия прицепного
устройства.
ВАЖНО: Следует прикрепить к прицепно-
му устройству хорошо видимую табличку
соответствующего размера, изготовлен-
ную из надежного материала, со следую-
щим текстом:
МАКСИМАЛЬНАЯ НАГРУЗКА НА ШАР
ПРИЦЕПНОГО УСТРОЙСТВА 70 кг
Рис. 3
Стандартный шар
Имеющееся
отверстие
Имеющееся
отверстие
Существующий болт
Существующий болт
Существующий болт
Существующий болт
Существующий болт
В зависимости от на-
грузки
После установки прицеп-
ного устройства техно-
логические отверстия должны
быть загерметизированы, что-
бы исключить проникновение
в салон автомобиля отработав-
ших газов.

Содержание