Skil 6220 LA [7/100] Application advice
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Skil 6220 LA [7/100] Application advice

Skil 6220 LA [7/100] Application advice
7
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc.,
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations dierent
from those intended could result in a hazardous situation.
5) SERVICE
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
SAFETY INSTRUCTIONS FOR DRILL/DRIVERS
• Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
• Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool (tools with
a rating of 230V or 240V can also be connected to a
220V supply)
• SKIL can assure awless functioning of the tool only
when original accessories are used
• Use only accessories with an allowable speed matching
at least the highest no-load speed of the tool
• This tool should not be used by people under the age of
16 years
• Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
• Always keep the cord away from moving parts of the tool
• If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug
• Never use the tool when cord is damaged; have it
replaced by a qualied person
• If the drill bit becomes unexpectedly jammed (causing a
sudden, dangerous reaction), immediately switch o
the tool
• In case of electrical or mechanical malfunction,
immediately switch o the tool and disconnect the plug
• Secure the workpiece (a workpiece clamped with
clamping devices or in a vice is held more securely than
by hand)
• Hold the power tool only by the insulated gripping
surfaces when performing an operation where the
accessory may contact hidden wiring or its own
power cord (contact with a “live” wire will also make
exposed metal parts of the power tool “live” and shock
the operator)
• Use suitable detectors to find hidden utility lines or
call the local utility company for assistance (contact
with electric lines can lead to re or electrical shock;
damaging a gas line can result in an explosion;
penetrating a water pipe will cause property damage or
an electrical shock)
• Do not work materials containing asbestos (asbestos
is considered carcinogenic)
• Dust from material such as paint containing lead, some
wood species, minerals and metal may be harmful
(contact with or inhalation of the dust may cause allergic
reactions and/or respiratory diseases to the operator or
bystanders); wear a dust mask and work with a dust
extraction device when connectable
• Certain kinds of dust are classied as carcinogenic
(such as oak and beech dust) especially in conjunction
with additives for wood conditioning; wear a dust
mask and work with a dust extraction device
when connectable
• Follow the dust-related national requirements for the
materials you want to work with
• When you put away the tool, switch o the motor and
ensure that all moving parts have come to a
complete standstill
• Alwaysdisconnectplugfrompowersourcebefore
making any adjustment or changing any accessory
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
• If for any reason the old plug is cut o the cord of this tool,
it must be disposed of safely and not left unattended
USE
• On/O 4
• Speed control for smooth starting 5
• Changing direction of rotation 6
- when not properly set in left/right position, switch A 2
cannot be activated
! change direction of rotation only when tool is at a
complete standstill
• Changing bits 7
- insert the bit as deep as possible in the chuck
! do not use bits with a damaged shank
• Torque control (VariTorque) 8
- output torque will increase as clutch ring D is rotated
from 1 to 20; position E will lock up the clutch to permit
drilling or driving heavy duty work
- when turning in a screw, rst try VariTorque position 1
and increase until the desired depth has been reached
• Holding and guiding the tool 9
! while working, always hold the tool at the
grey-coloured grip area(s)
- keep ventilation slots F 2 uncovered
- do not apply too much pressure on the tool; let the tool
do the work for you
APPLICATION ADVICE
• Use the appropriate bits 0
! only use sharp bits
• When drilling ferrous metals
- pre-drill a smaller hole, when a large hole is required
- lubricate drill bit occasionally with oil
• When turning in a screw at/near the cross cut end or an
edge of wood, pre-drill a hole in order to avoid cracking of
the wood
• For an optimal use of the tool a steady pressure on the
screw is required, especially while removing
• When screwdriving in hard wood one should pre-drill
a hole
• Splinterfree drilling in wood !
• For more tips see www.skil.com

Содержание

Похожие устройства

f Keep cutting tools sharp and clean Properly Certain kinds of dust are classified as carcinogenic such as oak and beech dust especially in conjunction with additives for wood conditioning wear a dust maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control mask and work with a dust extraction device when connectable g Use the power tool accessories and tool bits etc In accordance with these Instructions taking Into account the working conditions and the work to be performed Use of the power tool for operations diflerent Follow the dust related national requirements for the materials you want to work with When you put away the tool switch off the motor and ensure that all moving parts have come to a complete standstill from those intended could result in a hazardous situation 5 SERVICE a Have your power tool serviced by a qualified repair person using only identical replacement parts This Always disconnect plug from power source before making any adjustment or changing any accessory will ensure that the safety of the power tool is maintained WHEN CONNECTING NEW 3 PIN PLUG U K ONLY Do not connect the blue neutral or brown live wire in the cord of this tool to the earth terminal of the plug If for any reason the old plug is cut off the cord of this tool it must be disposed of safely and not left unattended SAFETY INSTRUCTIONS FOR DRILL DRIVERS Avoid damage that can be caused by screws nails and other elements in your workpiece rem we them before you start working Always check that the supply voltage is the same as the voltage indicated on the nameplate of the tool tools with a rating of 230V or 240V can also be connected to a 220V supply SKIL can assure flawless functioning of the tool only when original accessories are used Use only accessories with an allowable speed matching at least the highest no load speed of the tool This tool should not be used by people under the age of 16 years Use completely unrolled and safe extension cords with a capacity of 16 Amps U K 13 Amps Always keep the cord away from moving parts of the tool If the cord is damaged or cut through while working do not touch the cord but immediately disconnect the plug Never use the tool when cord is damaged have it replaced by a qualified person If the drill bit becomes unexpectedly jammed causing a sudden dangerous reaction immediately switch off the tool In case of electrical or mechanical malfunction immediately switch off the tool and disconnect the plug Secure the workpiece a workpiece clamped with clamping devices or in a vice is held more securely than by hand USE On Off Speed control for smooth starting Changing direction of rotation when not properly set in left right position switch A cannot be activated I change direction of rotation only when tool is at a complete standstill Changing bits 7 insert the bit as deep as possible in the chuck I do not use bits with a damaged shank Torque control VariTorque output torque will increase as clutch ring D is rotated from 1 to 20 position E will lock up the clutch to permit drilling or driving heavy duty work when turning in a screw first try VariTorque position 1 and increase until the desired depth has been reached Hol ding and guidi ng the tool while working always hold the tool at the grey coloured grip area s keep ventilation slots F uncovered do not apply too much pressure on the tool let the tool do the work for you Hold the power tool only by the insulated gripping surfaces when performing an operation where the accessory may contact hidden wiring or Its own power cord contact with a live wire will also make APPLICATION ADVICE Use the appropriate bits only use sharp bits When drilling ferrous metals pre drill a smaller hole when a large hole is required lubricate drill bit occasionally with oil When turning in a screw at near the cross cut end or an edge of wood pre drill a hole in order to avoid cracking of the wood For an optimal use of the tool a steady pressure on the screw is required especially while removing When screwdriving in hard wood one should pre drill a hole Splinterfree drilling in wood For more tips see www skil com exposed metal parts of the power tool live and shock the operator Use suitable detectors to find hidden utility lines or call the local utility company for assistance contact with electric lines can lead to fire or electrical shock damaging a gas line can result in an explosion penetrating a water pipe will cause property damage or an electrical shock Do not work materials containing asbestos asbestos is considered carcinogenic Dust from material such as paint containing lead some wood species minerals and metal may be harmful contact with or inhalation of the dust may cause allergic reactions and or respiratory diseases to the operator or bystanders wear a dust mask and work with a dust extraction device when connectable 7

Скачать