Home
Главная
Skil
Шлифовальная Машина
1220 NA
Инструкция по эксплуатации Страница: 6

Skil 1220 NA Инструкция по эксплуатации онлайн [6/104] 92740

e) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc., in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations dierent

from those intended could result in a hazardous situation.

5) SERVICE

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

SAFETY INSTRUCTIONS FOR SANDERS

• Avoid damage that can be caused by screws, nails and

other elements in your workpiece; remove them before

you start working

• Always keep the cord away from moving parts of the tool;

direct the cord to the rear, away from the tool

• Secure the workpiece (a workpiece clamped with

clamping devices or in a vice is held more securely than

by hand)

• When you put away the tool, switch o the motor and

ensure that all moving parts have come to a complete

standstill

• Use completely unrolled and safe extension cords with a

capacity of 16 Amps (U.K. 13 Amps)

• In case of electrical or mechanical malfunction,

immediately switch o the tool and disconnect the plug

• SKIL can assure awless functioning of the tool only

when original accessories are used

• This tool should not be used by people under the age of

16 years

• The noise level when working can exceed 85 dB(A); wear

ear protection

• Hold power tool by insulated gripping surfaces,

because the belt may contact its own cord (cutting a

“live” wire may make exposed metal parts of the power

tool “live” and could give the operator an electric shock)

• If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

• Never use the tool when cord is damaged; have it

replaced by a qualied person

• Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool (tools with

a rating of 230V or 240V can also be connected to a

220V supply)

• This tool is not suitable for wet sanding

• Do not work materials containing asbestos (asbestos

is considered carcinogenic)

• Dust from material such as paint containing lead, some

wood species, minerals and metal may be harmful

(contact with or inhalation of the dust may cause allergic

reactions and/or respiratory diseases to the operator or

bystanders); wear a dust mask and work with a dust

extraction device when connectable

• Certain kinds of dust are classied as carcinogenic (such

as oak and beech dust) especially in conjunction with

additives for wood conditioning; wear a dust mask and

work with a dust extraction device when

connectable

• Follow the dust-related national requirements for the

materials you want to work with

• When sanding metal, sparks are generated; do not use

dustbag/dustbox/vacuum cleaner and keep other

persons and combustible material from work area

• Do not touch the running sanding belt

• Do not continue to use worn, torn or heavily clogged

sanding belts

• Wear protective gloves, safety glasses, close-tting

clothes and hair protection (for long hair)

• Alwaysdisconnectplugfrompowersourcebefore

making any adjustment or changing any accessory

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

• If for any reason the old plug is cut o the cord of this tool,

it must be disposed of safely and not left unattended

USE

• On/o switch

- switch on/o the tool by pulling/releasing trigger A 2

! before the sanding surface reaches the

workpiece, you should switch on the tool

! before switching off the tool, you should lift it

from the workpiece

• Switch locking for continuous use

- pull trigger A 2

- press knob B 2 with your thumb

- release the trigger

- unlock the switch by pulling again trigger A 2 and

then releasing it

• Changing of sanding belts 4

! disconnect the plug

- lift lever C

- remove sanding belt

- insert new belt with arrows printed at inner side of belt

pointing in same direction as arrow D on tool

- push lever back

! change sanding belts in time

! never fold sanding belts

• Automatic belt centering (ABC)

- centers belt automatically when switching on tool

- keeps belt centered while sanding

In case belt runs o tool (mostly caused by inferior belt

quality), you should

- switch on the tool

- adjust screw E 2 till the sanding belt is running in line

with the at side of the tool

- use new belt, if belt still runs o tool

• Dust suction 5

! empty dustbag F regularly for optimal dust

pick-up performance

- when using tool with vacuum cleaner, mount vacuum

cleaner adaptor G as illustrated

! do not use dustbag/vacuum cleaner when

sanding metal

Содержание

Похожие устройства

e Maintain power tools Check for misalignment or binding of moving parts breakage of parts and any other condition that may affect the power tool s operation If damaged have the power tool repaired before use Many accidents are caused by poorly maintained power tools f Keep cutting tools sharp and clean Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control g Use the power tool accessories and tool bits etc In accordance with these Instructions taking Into account the working conditions and the work to be performed Use of the power tool for operations different from those intended could result in a hazardous situation 5 SERVICE a Have your power tool serviced by a qualified repair person using only identical replacement parts This will ensure that the safety of the power tool is maintained Certain kinds of dust are classified as carcin as oak and beech dust especially in conju additives for wood conditioning wear a du work with a dust extraction device when connectable Follow the dust related national requiremen materials you want to work with When sanding metal sparks are generated dustbag dustbox vacuum cleaner and kee persons and combustible material from wo Do not touch the running sanding belt Do not continue to use worn torn or heavily sanding belts Wear protective gloves safety glasses clos clothes and hair protection for long hair Always disconnect plug from power source making any adjustment or changing any a WHEN CONNECTING NEW 3 PIN PLUG U Do not connect the blue neutral or brown in the cord of this tool to the earth termina If for any reason the old plug is cut off the c it must be disposed of safely and not left u SAFETY INSTRUCTIONS FOR SANDERS Avoid damage that can be caused by screws nails and other elements in your workpiece remove them before you start working Always keep the cord away from moving parts of the tool direct the cord to the rear away from the tool Secure the workpiece a workpiece clamped with clamping devi ces or i n a vice i s hel d more securely than by hand When you put away the tool switch off the motor and ensure that all moving parts have come to a complete standstill Use completely unrolled and safe extension cords with a capacity of 16 Amps U K 13 Amps In case of electrical or mechanical malfunction immediately switch off the tool and disconnect the plug SKIL can assure flawless functioning of the tool only when original accessories are used This tool should not be used by people under the age of 16 years The noise level when working can exceed 85 dB A wear ear protection Hold power tool by insulated gripping surfaces because the belt may contact Its own cord cutting a live wire may make exposed metal parts of the power tool live and could give the operator an electric shock If the cord is damaged or cut through while working do not touch the cord but immediately disconnect the plug Never use the tool when cord is damaged have it replaced by a qualified person Always check that the supply voltage is the same as the voltage indicated on the nameplate of the tool tools with a rating of 230V or 240V can also be connected to a 220V supply This tool is not suitable for wet sanding Do not work materials containing asbestos asbestos is considered carcinogenic Dust from material such as paint containing lead some wood species minerals and metal may be harmful contact with or inhalation of the dust may cause allergic reactions and or respiratory diseases to the operator or bystanders wear a dust mask and work with a dust extraction device when connectable USE On off switch switch on off the tool by pulling releasing before the sanding surface reaches the workpiece you should switch on the to I before switching off the tool you should from the workpiece Switch locking for continuous use pull trigger A press knob B with your thumb release the trigger unlock the switch by pulling again trigger then releasing it Changing of sanding belts I disconnect the plug littlever C remove sanding belt insert new belt with arrows printed at inn pointing in same direction as arrow D o push lever back change sanding belts In time never fold sanding belts Automatic belt centering ABC centers belt automatically when switchin keeps belt centered while sanding In case belt runs off tool mostly caused b quality you should switch on the tool adjust screw E till the sanding belt is ru with the fl at side of th e tool use new belt if belt still runs off tool Dust suction empty dustbag F regularly for optimal du pick up performance when using tool with vacuum cleaner m cleaner adaptor G as illustrated I do not use dustbag vacuum cleaner whe sanding metal 6

Скачать