Karcher HDS 2000 Super [21/185] Start up

Karcher HDS 2000 Super [21/185] Start up
HDS 2000 Super
GB
21
4. Start-up
4.7 Connecting the water
See technical data, chap. 3 for connected
loads.
Attach the supply hose to the appliance and to
the water line. The supply hose is not included
in standard delivery.
If you draw in the water from an open tank,
you should
disconnect the water supply from the pump
head
unscrew the upper supply hose from the
water tank and connect to the pump head.
use a water supply hose which has a
minimum diameter of 3/4" and a suction
filter.
Until the pump has drawn in the water, you
should:
rotate the pressure and volume control to
“MAX”,
close the detergent metering valve.
4.8 Connecting the power
See technical data, chap. 3 for connected
loads.
The voltage stated on the rating plate must
correspond to the voltage of the power source.
First, position the appliance switch to “STOP”
and then put the electric plug into the socket.
If the motor rotates in the wrong direction, the
electronic control circuit will switch the motor
off after a few seconds. The INCORRECT
MOTOR ROTATION warning light illuminates.
Disconnect the power input plug. This plug is
equipped with a device for reversing polarity.
Apply a screwdriver at the prescribed point,
press it inwards and rotate both terminals
through 180°.
Attach the power input plug again.
If you are using an extension lead, it should
always be completely unwound from the cable
drum and have an adequate cross-section.
Mains voltage 10 m 30 m
230 V 6 mm² 10 mm²
400 V 4 mm² 6 mm²
4.9 Intended use
Use the appliance to clean machines,
vehicles, buildings, tools, etc.
Clean facades, patios, garden implements,
etc. with the high-pressure spray only, i.e.
without detergent. We recommend the dirt
blaster, a special accessory, for stubborn
dirt.
If the machine is used at petrol stations or in
other hazardous areas, the appropriate safety
regulations must be observed.
Please ensure waste water containing mineral
oil
does not contaminate soil, lakes and rivers or
the sewerage system. Therefore, please wash
engines and underbodies only in appropriate
washing installations provided with oil traps.

Содержание

HDS 2000 Super 4 Start up 4 7 Connecting the water 4 9 Intended use See technical data chap 3 for connected loads Attach the supply hose to the appliance and to the water line The supply hose is not included in standard delivery Clean facades patios garden implements etc with the high pressure spray only i e without detergent We recommend the dirt blaster a special accessory for stubborn dirt If you draw in the water from an open tank you should disconnectthewatersupplyfromthepump head unscrew the upper supply hose from the water tank and connect to the pump head use a water supply hose which has a minimum diameter of 3 4 and a suction filter Until the pump has drawn in the water you should Use the appliance to clean vehicles buildings tools etc machines If the machine is used at petrol stations or in otherhazardousareas the appropriate safety regulations must be observed Please ensure waste water containing mineral oil does not contaminate soil lakes and rivers or the sewerage system Therefore please wash engines and underbodies only in appropriate washing installations provided with oil traps rotate the pressure and volume control to MAX close the detergent metering valve 4 8 Connecting the power See technical data chap 3 for connected loads The voltage stated on the rating plate must correspond to the voltage of the power source First position the appliance switch to STOP and then put the electric plug into the socket If the motor rotates in the wrong direction the electronic control circuit will switch the motor off after a few seconds The INCORRECT MOTOR ROTATION warning light illuminates Disconnect the power input plug This plug is equipped with a device for reversing polarity Apply a screwdriver at the prescribed point press it inwards and rotate both terminals through 180 Attach the power input plug again If you are using an extension lead it should always be completely unwound from the cable drum and have an adequate cross section Mains voltage 10 m 30 m 230 V 6 mm2 10mm2 400 V 4 mm2 6mm2 21

Скачать
Случайные обсуждения