Makita BHP 441 RFE [10/32] Accessories
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Makita BHP 441 RFE [10/32] Accessories

Makita BHP 441 RFE [10/32] Accessories
10
The adjusting ring can be aligned in any torque levels for
this operation. Then proceed as follows.
Drilling in wood
When drilling in wood, the best results are obtained with
wood drills equipped with a guide screw. The guide screw
makes drilling easier by pulling the bit into the workpiece.
Drilling in metal
To prevent the bit from slipping when starting a hole, make
an indentation with a center-punch and hammer at the
point to be drilled. Place the point of the bit in the indenta-
tion and start drilling.
Use a cutting lubricant when drilling metals. The excep-
tions are iron and brass which should be drilled dry.
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off and the bat-
tery cartridge is removed before attempting to perform
inspection or maintenance.
Replacing carbon brushes
Replace when they wear down to the limit mark. Keep the
carbon brushes clean and free to slip in the holders. Both
carbon brushes should be replaced at the same time. Use
only identical carbon brushes. (Fig. 15)
Use a screwdriver to remove two screws then remove the
rear cover. (Fig. 16)
Raise the arm part of the spring and then place it in the
recessed part of the housing with a slotted bit screwdriver
of slender shaft or the like. (Fig. 17)
Use pliers to remove the carbon brush caps of the carbon
brushes. Take out the worn carbon brushes, insert the
new ones and replace the carbon brush caps in reverse.
(Fig. 18)
Make sure that the carbon brush caps have fit into the
holes in brush holders securely. (Fig. 19)
Reinstall the rear cover and tighten two screws securely.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be per-
formed by Makita Authorized Service Centers, always
using Makita replacement parts.
ACCESSORIES
CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita service center.
• Drill bits
• Hammer drill bits
• Screw bits
• Blow-out bulb
• Safety goggles
• Various type of Makita genuine batteries and chargers
• Grip assembly
•Depth rod
•Hook
• Rubber pad assembly
• Wool bonnet
• Foam polishing pad
For Model BHP441
For European countries only
Noise and Vibration
The typical A-weighted noise levels are
sound pressure level: 86 dB (A)
sound power level: 97 dB (A)
Uncertainty: 3 dB
- Wear ear protection. -
The typical weighted root mean square acceleration　
value is 6 m/s
2
.
These values have been obtained according to EN60745.
For Model BHP451
For European countries only
Noise and Vibration
The typical A-weighted noise levels are
sound pressure level: 87 dB (A)
sound power level: 98 dB (A)
Uncertainty: 3 dB
- Wear ear protection. -
The typical weighted root mean square acceleration　
value is 6 m/s
2
.
These values have been obtained according to EN60745.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product
is in compliance with the following standards of standard-
ized documents, EN60745, EN55014 in accordance with
Council Directives, 89/336/EEC, 98/37/EC.
Yasuhiko Kanzaki
CE 2005
Director
MAKITA INTERNATIONAL EUROPE LTD.
Michigan Drive, Tongwell, Milton Keynes, Bucks MK15
8JD, ENGLAND
Responsible manufacturer:
Makita Corporation Anjo Aichi Japan

Содержание

Похожие устройства

The adjusting ring can be aligned in any torque levels for this operation Then proceed as follows Drilling in wood When drilling in wood the best results are obtained with wood drills equipped with a guide screw The guide screw makes drilling easier by pulling the bit into the workpiece Drilling in metal To prevent the bit from slipping when starting a hole make an indentation with a center punch and hammer at the point to be drilled Place the point of the bit in the indenta tion and start drilling Use a cutting lubricant when drilling metals The excep tions are iron and brass which should be drilled dry MAINTENANCE CAUTION Always be sure that the tool is switched off and the bat tery cartridge is removed before attempting to perform inspection or maintenance Replacing carbon brushes Replace when they wear down to the limit mark Keep the carbon brushes clean and free to slip in the holders Both carbon brushes should be replaced at the same time Use only identical carbon brushes Fig 15 Use a screwdriver to remove two screws then remove the rear cover Fig 16 Raise the arm part of the spring and then place it in the recessed part of the housing with a slotted bit screwdriver of slender shaft or the like Fig 17 Use pliers to remove the carbon brush caps of the carbon brushes Take out the worn carbon brushes insert the new ones and replace the carbon brush caps in reverse Fig 18 Make sure that the carbon brush caps have fit into the holes in brush holders securely Fig 19 Reinstall the rear cover and tighten two screws securely Various type of Makita genuine batteries and chargers Grip assembly Depth rod Hook Rubber pad assembly Wool bonnet Foam polishing pad For Model BHP441 For European countries only Noise and Vibration The typical A weighted noise levels are sound pressure level 86 dB A sound power level 97 dB A Uncertainty 3 dB Wear ear protection The typical weighted root mean square acceleration value is 6 m s2 These values have been obtained according to EN60745 For Model BHP451 For European countries only Noise and Vibration The typical A weighted noise levels are sound pressure level 87 dB A sound power level 98 dB A Uncertainty 3 dB Wear ear protection The typical weighted root mean square acceleration value is 6 m s2 These values have been obtained according to EN60745 EC DECLARATION OF CONFORMITY We declare under our sole responsibility that this product is in compliance with the following standards of standard ized documents EN60745 EN55014 in accordance with Council Directives 89 336 EEC 98 37 EC Yasuhiko Kanzaki CE 2005 To maintain product SAFETY and RELIABILITY repairs any other maintenance or adjustment should be per formed by Makita Authorized Service Centers always using Makita replacement parts ACCESSORIES CAUTION These accessories or attachments are recommended for use with your Makita tool specified in this manual The use of any other accessories or attachments might present a risk of injury to persons Only use accessory or attachment for its stated purpose If you need any assistance for more details regarding these accessories ask your local Makita service center Drill bits Hammer drill bits Screw bits Blow out bulb Safety goggles 10 Director MAKITA INTERNATIONAL EUROPE LTD Michigan Drive Tongwell Milton Keynes Bucks MK15 8JD ENGLAND Responsible manufacturer Makita Corporation Anjo Aichi Japan

Скачать
Случайные обсуждения

Ответы 1

Как снять и заменить быстро зажимной патрон?
6 лет назад

Ответы 1

Сколько оборотов на 1 -2-3 скорости?
6 лет назад