![Fluke 726 [51/80] Setting 0 and 100 output parameters](/img/pdf.png)
Fluke 726 [51/80] Setting 0 and 100 output parameters
![Fluke 726 [51/80] Setting 0 and 100 output parameters](/views2/1005547/page51/bg33.png)
Multifunction Process Calibrator
Setting 0 % and 100 % Output Parameters
41
Setting 0 % and 100 % Output
Parameters
For current output, the Calibrator assumes that 0 %
corresponds to 4 mA and 100 % corresponds to 20 mA.
For other output parameters, 0 % and 100 % points must
be set before using the step and ramp functions. Proceed
as follows:
1. If necessary, press
M for SOURCE mode.
2. Select the desired source function and use the arrow
keys to enter the value. This example is temperature
source using 100 °C and 300 °C values for source.
3. Enter 100 °C then press and hold
J to store the
value.
4. Enter 300 °C then press and hold
G to store the
value.
This setting can now be used for the following:
• Manually stepping an output in 25 %
increments.
• Switch between the 0 and 100 % span points by
momentarily pushing
J or G.
% Error Functionality
Percentage Error is available for every range on the
lower display. The calculation is based on a mA
percentage deviation
from the value measured on the
upper display to the value sourced on the lower display
0 % mA and 100 % mA are fixed to 4 and 20 mA. 0 %
and 100 % for the lower display are set in source using
J and G, refer to “Setting 0% and 100% Output
Parameters”.
Stepping and Ramping the Output
Two additional features are available for adjusting the
value of source functions:
• Stepping the output manually with the
H and I
keys, or in automatic mode
• Ramping the output
Stepping and ramping apply to all functions except
pressure, which requires use of an external pressure
source.
Содержание
- Multifunction process calibrator users manual 1
- Limited warranty and limitation of liability 2
- Table of contents 3
- Title page 3
- Contents 5
- List of tables 7
- Table title page 7
- Figure title page 9
- List of figures 9
- Contacting fluke 11
- Introduction 11
- Multifunction process calibrator 11
- Safety information 13
- Standard equipment 13
- Xw warning 13
- Xw warning 14
- W caution 15
- Ac72 alligator clips 16
- Bec01f eps 16
- Figure 1 standard equipment 16
- Stackable test leads 16
- Tl75 test lead set 16
- Users manual 16
- Symbols 17
- Figure 2 input output terminals and connectors 18
- Figure 2 shows the calibrator input and output terminals table 3 explains their use 18
- Getting acquainted with the calibrator 18
- Input and output terminals 18
- Users manual 18
- Bec41f eps 20
- Figure 3 keys 20
- Figure 3 shows the calibrator keys and table 4 explains their use 20
- Users manual 20
- Display 23
- Figure 4 elements of a typical display 23
- Figure 4 shows the elements of a typical display 23
- Multifunction process calibrator getting acquainted with the calibrator 23
- Configuration menus 24
- Contrast adjustment 24
- Celcius and fahrenheit c and f 25
- Frequency pulse output voltage 25
- Pulse output frequency 25
- Shut down mode 25
- Getting started 26
- Hart resistor on off 26
- Resistor on off 26
- Voltage to voltage test 26
- Bec39f eps 27
- Config selection 27
- Figure 6 voltage to voltage test 27
- Multifunction process calibrator getting started 27
- Precision calibrator 27
- Save recall 27
- Current measurement with loop power 28
- Measuring electrical parameters upper display 28
- Using measure mode 28
- Figure 8 connections for supplying loop power 29
- Hart communicator 29
- Meas source 29
- Multifunction process calibrator using measure mode 29
- Precision calibrator 29
- Save recall 29
- Measuring electrical parameters lower display 30
- Measuring temperature 31
- Using thermocouples 31
- W caution 31
- Figure 10 measuring temperature with a thermocouple 33
- Multifunction process calibrator using measure mode 33
- Process temperature 33
- Tc miniplug 33
- Warning 30 v maximum to 33
- Prt custom curves 34
- Using resistance temperature detectors rtds 34
- Figure 11 measuring temperature with an rtd measuring 2 3 and 4 wire resistance 36
- Users manual 36
- Measuring pressure 37
- W caution 37
- W warning 37
- A for 3 second 38
- Zeroing with absolute pressure modules 38
- Differential module 39
- Figure 13 connections for measuring pressure 39
- Gage module 39
- Isolation valve 39
- Multifunction process calibrator using measure mode 39
- Simulating a 4 to 20 ma transmitter 40
- Sourcing 4 to 20 ma 40
- Using source mode 40
- Figure 14 connections for simulating a 4 to 20 ma transmitter 41
- Loop power supply 41
- Multifunction process calibrator using source mode 41
- Readout or controller 41
- Sourcing other electrical parameters 42
- Figure 15 electrical sourcing connections 43
- Measure source measure 43
- Multifunction process calibrator using source mode 43
- Simulating thermocouples 44
- W caution 44
- Color depends on type of tc 45
- Figure 16 connections for simulating a thermocouple 45
- Multifunction process calibrator using source mode 45
- Precision calibrator 45
- Tc miniplug 45
- Simulating rtds 46
- Config selection 47
- Figure 17 connections for simulating 3 and 4 wire rtd 47
- Multifunction process calibrator using source mode 47
- Precision calibrator 47
- Save recall 47
- Sensor terminals 47
- Source 47
- V ma loop switch test 47
- Sourcing pressure 48
- W caution 48
- W warning 48
- Figure 18 connections for sourcing pressure 50
- Hand pump 50
- Measure ma source pressure 24 v loop power enabled 50
- Pressure module 50
- To unit under test 50
- Users manual 50
- Error functionality 51
- Setting 0 and 100 output parameters 51
- Stepping and ramping the output 51
- Auto ramping the output 52
- L is presse 52
- Manually stepping the ma output 52
- Store a setup 52
- Storing and recalling setups 52
- Recall a setup 53
- Storing and recalling data 53
- Storing data 53
- Pulse train source read 54
- Recall data 54
- Calibrating a transmitter 55
- Figure 20 calibrating a thermocouple transmitter 56
- Hart communicator 56
- Meas source 56
- Precision calibrator 56
- Save recall 56
- Users manual 56
- Calibrating a pressure transmitter 57
- Figure 21 calibrating a pressure to current p i transmitter 58
- Hand pump 58
- Meas source 58
- Precision calibrator 58
- Pressure module 58
- Save recall 58
- Users manual 58
- Calibrating an i p device 59
- Figure 22 calibrating a current to pressure i p transmitter 60
- Hart communicator 60
- Measure pressure source ma 60
- Precision calibrator 60
- Pressure module 60
- Users manual 60
- Pressure switch test 61
- Testing an output device 61
- Functionality 62
- Hart functionality 62
- Remote control commands 62
- Maintenance 63
- Replacing the batteries 63
- Warning 63
- Cleaning the calibrator 64
- Replacement parts 64
- Service center calibration or repair 64
- W caution 64
- Figure 25 replacement parts 65
- Maintenance 65
- Multifunction process calibrator 65
- Accessories 66
- External fluke pressure module compatibility 66
- Dc ma measurement and source 69
- Dc voltage measurement and source 69
- Multifunction process calibrator 69
- Specifications 69
- Frequency measurement 70
- Ohms measurement 70
- Ohms source 70
- Users manual 70
- Frequency source 71
- Multifunction process calibrator 71
- Specifications 71
- Temperature thermocouples 71
- Users manual 72
- Multifunction process calibrator 73
- Rtd accuracy read and source its 90 73
- Specifications 73
- Loop power supply 74
- Pressure measurement 74
- Pulse read and pulse source 74
- Users manual 74
- Voltage 24 v maximum current 22 ma short circuit protected 74
- General specifications 75
- Multifunction process calibrator 75
- Specifications 75
Похожие устройства
- Telwin Superior Plasma 90HF 400V Инструкция по эксплуатации
- Centurion NEXT v.1 Инструкция по эксплуатации
- Belkin F8N344cw034 Gr Инструкция по эксплуатации
- LG MH-6352JS Инструкция по эксплуатации
- Dunlop 105Q Инструкция по эксплуатации
- Electrolux EWS 106410 W Инструкция по эксплуатации
- Fluke 741B Инструкция по эксплуатации
- Condtrol UBEXI XG 700 Инструкция по эксплуатации
- Centurion BLOCK POST Инструкция по эксплуатации
- LG MH-6352J Инструкция по эксплуатации
- Belkin F8N463cw Bl Инструкция по эксплуатации
- Dunlop M 88 Инструкция по эксплуатации
- Fluke 743B Инструкция по эксплуатации
- Electrolux EWS 126510 W Инструкция по эксплуатации
- Ada Schmidt Hammer 225 А00191 Инструкция по эксплуатации
- LG MH-6352G Инструкция по эксплуатации
- Dunlop QZ-1 Инструкция по эксплуатации
- Fluke 744 Инструкция по эксплуатации
- Belkin F8N357cwBKB Bl Инструкция по эксплуатации
- Electrolux EWT 105410 W Инструкция по эксплуатации