Einhell RT-SB 250 U Инструкция по эксплуатации онлайн [21/68] 74043
![Einhell RT-SB 250 U Инструкция по эксплуатации онлайн [21/68] 74043](/views2/1079469/page21/bg15.png)
21
GB
appropriate openings on one of the intermediate
struts (C) as far as the stop (Figure 13). Screw
the bottom cross struts (E) to the intermediate
strut (C) using two screws (L), washers (K) and
nuts (I) in each case, as shown in Figures 14 - 15.
앬 On the same side of the base frame, slide the two
top cross struts (F) as far as the stop into the
appropriate openings on the side part (B) (Figure
16). Insert a corner bracing (Y) into each opening
on the side part (B). Note that each of the corner
bracings (Y) only fits on one side of the base
frame; this is the case when the openings on the
side part (B), the top cross struts (F) and the
corner bracings (Y) are positioned precisely on
top of each other (Figure 18).
앬 Now screw together the top cross struts (F),
corner bracings (Y), side part (B) using two
screws (L), washers (K) and nuts (I) in each case,
as shown in Figures 18.
앬 Insert the two base frame parts in such a way that
the bottom and top cross struts (E, F) are
positioned in the relevant openings on the side
part (B) and the cross strut (C) (Figure 19).
앬 Screw the bottom cross struts (E) to the other part
of the base frame (Figure 20/1) as described
under 5.
앬 Screw the top cross struts (F) to the other part of
the base frame (Figure 20/2) as described under
6.
앬 Fasten the two tilt guards (26) to the cross struts
(C) with two nuts (I), washers (K) and screws (L)
in each case (Figure 21).
앬 Secure the connection pieces (4) to the corners
of the machine frame with the screws (T). Place
the machine frame onto the mounted base frame.
Slide the screws (M) through the connection
pieces and secure them with the washers (J) and
nuts (I).
7.2 Assembling the saw table (Figures 24-27)
Slacken the screw heads (45) on the underside of
the saw table (15) and remove the chain bar (2)
from the saw table.
Lead the blade through the slot (a) in the
machine table and place the machine table on
the table guide so that the clamping screw (47)
fits through the mounting (48).
Screw the saw table tight with the locking grip
(18).
Place the chain bar (2) on the saw table (15) so
that the screw heads (50) slide into the guide
slots (51).
Check that the blade (25) runs freely and does
not touch the saw table.
To remove the saw blade guard, proceed in
reverse order.
7.3 Tensioning the blade (Figure 1,28)
CAUTION! Remove the tension from the blade
if the bandsaw is not going to be used for some
time. Be sure to re-tension the blade before you
start the machine.
Turn the tightening screw (9) for tensioning the
blade (25) in a clockwise direction.
The correct blade tension can be checked by
applying pressure to the side of the blade with
your finger, somewhere in the middle between
the two blade pulleys (7 + 8). You should only
be able to bend the blade (25) very slightly
(approx. 1-2 mm).
CAUTION! The blade may break if the tension
is too high. BEWARE OF INJURY!
If the tension
is too low, the powered blade pulley (7) will spin
while the blade does not move.
7.4 Adjusting the blade (Figure 1,29-31)
CAUTION! The blade must be properly clamped
before the blade can be adjusted.
Undo the fasteners (13) and open the side cover
(12,14).
Turn the upper blade pulley (8) slowly in a
clockwise direction.
The blade (25) should run centrally on the blade
pulley (8).
If it does not, the angle at which the upper blade
pulley (8) tilts must be adjusted.
If the blade (25) runs more towards the rear of
the blade pulley (8), the setting screw (22) must
be turned in anticlockwise direction. Then turn
the blade pulley (8) slowly with the other hand to
check the position of the blade (25).
If the blade (25) runs towards the front edge of
the belt pulley (8), the setting screw (22) must
be turned in a clockwise direction.
After adjusting the upper blade pulley (8), check
the position of the blade (25) on the lower blade
pulley (7).
Again, the blade (25) should run in the middle of
the blade pulley (7). If it does not, the angle at
which the upper blade pulley (8) tilts must be
adjusted again.
The blade pulley must be turned several times
until the adjustment of the upper blade pulley (8)
has an effect on the position of the blade on the
lower blade pulley (7).
When adjustment has been completed, close
the side cover (12,14) again and secure it with
the fasteners (13).
Anleitung_RT_SB_250_U_SPK7:_ 10.02.2012 9:57 Uhr Seite 21
Содержание
- Art nr 43 80 0 i nr 01019 rt sb 1
- Bestimmungsgemäße verwendung 11
- Gerätebeschreibung abb 1 2 8 11
- Lieferumfang 11
- Sicherheitshinweise 11
- Geräuschemissionswerte 12
- Technische daten 12
- Vor inbetriebnahme 12
- Montage 13
- Bedienung 16
- Betrieb 16
- Entsorgung und wiederverwertung 17
- Reinigung wartung und ersatzteilbestellung 17
- Items supplied 19
- Machine layout figures 1 2 8 19
- Proper use 19
- Assembly 20
- Before putting the machine into operation 20
- Important notes 20
- Noise emission values 20
- Technical data 20
- Operation 23
- Maintenance 24
- Operation 24
- Ordering replacement parts 24
- Disposal and recycling 25
- Description de lʼappareil fig 1 2 8 27
- Utilisation conforme à lʼaffectation 27
- Volume de livraison 27
- Caractéristiques techniques 28
- Notes importantes 28
- Valeurs dʼémission de bruit 28
- Avant la mise en service 29
- Montage 29
- Commande 32
- Maintenance 33
- Service 33
- Commande de pièces de rechange 34
- Mise au rebut et recyclage 34
- Descrizione dellʼutensile fig 1 2 8 36
- Elementi forniti 36
- Uso corretto 36
- Avvertenze importanti 37
- Caratteristiche tecniche 37
- Prima della messa in esercizio 37
- Valori di emissione dei rumori 37
- Montaggio 38
- Esercizio 41
- Manutenzione 42
- Ordinazione dei pezzi di ricambio 42
- Smaltimento e riciclaggio 42
- Beskrivning av maskinen bild 1 2 8 44
- Leveransomfattning 44
- Ändamålsenlig användning 44
- Bulleremissionsvärden 45
- Före användning 45
- Montering 45
- Tekniska data 45
- Viktiga anvisningar 45
- Använda sågen 48
- Reservdelsbeställning 49
- Skrotning och återvinning 49
- Underhåll 49
- Irroita verkkopistoke kaikkien korjaus ja huoltotoimien ajaksi 50
- Laitteen kuvaus kuvat 1 2 8 51
- Määräysten mukainen käyttö 51
- Toimituksen laajuus 51
- Ennen käyttöönottoa 52
- Melunpäästöarvot 52
- Tekniset tiedot 52
- Tärkeitä ohjeita 52
- Asennus 53
- Käyttö 55
- Käyttö 56
- Huolto 57
- Käytöstäpoisto ja uusiokäyttö 57
- Varaosien tilaus 57
- 108 ec 58
- 14 ec_2005 88 ec 58
- 32 ec_2009 125 ec 58
- 396 ec_2009 142 ec 58
- 404 ec_2009 105 ec 58
- 686 ec_96 58 ec 58
- Anleitung_rt_sb_250_u_spk7 _ 10 2 012 9 57 uhr seite 58 58
- Annex iv 58
- Annex v annex vi 58
- Bandsäge rt sb 250 u einhell 58
- Isc gmbh eschenstraße 6 d 94405 landau isar 58
- Konformitätserklärung 58
- Landau isar den 07 2 012 58
- Standard references en 61029 1 en 61029 2 5 en 55014 1 en 55014 2 en 61000 3 2 en 61000 3 3 58
- Anleitung_rt_sb_250_u_spk7 _ 10 2 012 9 57 uhr seite 61 61
- T guarantee certificate 62
- P bulletin de garantie 63
- C certificato di garanzia 64
- U garantibevis 65
- Q takuutodistus 66
- Isc gmbh eschenstraße 6 94405 landau isar deutschland 67
- K garan tieurkunde 67
- Anleitung_rt_sb_250_u_spk7 _ 10 2 012 9 57 uhr seite 68 68
- Service hotline 01805 011 843 www isc gmbh info mo fr 8 00 18 00 uhr 68
Похожие устройства
- Binatone SI-4060 Инструкция по эксплуатации
- Einhell BT-SS 405 E Инструкция по эксплуатации
- Binatone SI-4022 Инструкция по эксплуатации
- Einhell RT-SS 120 L Инструкция по эксплуатации
- Binatone SI-4020 Инструкция по эксплуатации
- Einhell BT-SP 1300 Инструкция по эксплуатации
- Binatone SI-4016 Инструкция по эксплуатации
- Einhell RT-SP 260 D Инструкция по эксплуатации
- Binatone SI-4024 Инструкция по эксплуатации
- Einhell RT-SP 260 Инструкция по эксплуатации
- Binatone SI-2500 Инструкция по эксплуатации
- Einhell RT-VE 550 A Инструкция по эксплуатации
- Binatone SI-2510 Инструкция по эксплуатации
- Einhell BT-WW 1000 Инструкция по эксплуатации
- Binatone SI-2610 Инструкция по эксплуатации
- Einhell BT-US 400 Инструкция по эксплуатации
- Binatone SI-2600 Инструкция по эксплуатации
- Binatone SI-2550 Инструкция по эксплуатации
- Einhell BT-LS 65 U Инструкция по эксплуатации
- Einhell BT-LS 810 DB Инструкция по эксплуатации