![Einhell RT-SB 250 U [23/68] Operation](/img/pdf.png)
Einhell RT-SB 250 U [23/68] Operation
![Einhell RT-SB 250 U [23/68] Operation](/views2/1079469/page23/bg17.png)
23
GB
7.9 Replacing the blade (Figure 1,34)
Move the blade guide (11) into a position
approximately half way between the table (15)
and the machine frame (24).
Undo the fasteners (13) and open the side cover
(12).
Remove the chain bar (2).
Turn the tightening screw (9) anti-clockwise to
remove the tension from the blade (25).
Remove the blade (25) from the blade pulleys
(7,8) and take out through the slot in the table
(15).
Fit the new blade (25), aligned centrally on the
blade pulleys (7,8).
The teeth of the blade (25) must point
downwards in the direction of the table.
Tension the blade (25) (see 7.2).
Close the side cover (12) again.
7.10 Changing the rubber tires on the blade
pulleys (Fig. 35)
After a certain time the rubber tires (3) on the blade
pulleys (7,8) will get worn by the sharp teeth of the
blades and must be replaced.
Open the side cover (12).
Remove the blade (25) (see 7.7).
Lift the edge of the tire (3) with a screwdriver (P)
and remove from the blade pulley (8).
Repeat for the lower blade pulley (7).
Fit the new rubber tire (3), mount the blade (25)
and close the side cover (12) again.
7.11 Changing the table insert (Figure 36)
To prevent increased likelihood of injury the table
insert (17) should be changed whenever it is worn or
damaged.
Dismantle the saw table (15) (see 7.2).
Push out the worn table insert (17).
Fit the replacement table insert by following the
above in reverse.
7.12 Extractor socket (Fig. 1-2)
The bandsaw is equipped with two extractor sockets
for extracting sawdust and chips. The equipment may
only be used with the extractor function. The
extraction channels must be checked and cleaned at
regular intervals.
Make sure that the extractor connection which is not
in use is always sealed off with the supplied caps.
7.13 Adjusting the blade speed
(Fig. 45)
The bandsaw can be operated at two blade speeds.
To change the position proceed as follows:
Remove the tension from the drive belt (54) by
loosening the screw (56) at the motor and turning
the motor counterclockwise.
Move the belt to the desired position on the belt
pulley (55) and the lower blade pulley (7).
Tension the drive belt (54) by turning the motor in
clockwise direction and retighten the screw (56)
at the motor.
Important: Do not overtension the drive belt.
7.14 Transport
Remove the equipment from the base frame.
Transport the machine frame and the base frame
separately. Never lift the equipment by the saw table
and cover the blade with the blade guide during
transport.
8. Operation
8.1. ON/OFF switch (Fig. 37)
To turn the saw on, press the green button “I”.
To turn the saw off again, press the red button
“0”.
Your bandsaw has a switch with undervoltage
release. After a power failure you must re-
activate the switch.
8.2 Parallel stop (Fig. 38/39)
The parallel stop is used as a guide in slitting.
Place the parallel stop (23) onto the chain bar
(2) on the left or right and set the desired
dimension.
Clamp the parallel stop in the desired position
by pressing the clamping lever (27).
The chain bar can be used for thinner
workpieces as shown in Figure 38 and for
thicker workpieces as shown in Figure 39.
8.3. Angular cuts (Figure 26/40)
To enable you to perform angular cuts parallel to the
blade (25), the table (15) can be tilted forwards
between 0° - 45°.
Undo the fixing handle (18).
Tilt the saw table (15) forward until required
angle value has been set on the man scale (16).
Re-tighten the fixing handle (18).
Important: When the table (15) is tilted, place
the parallel stop (23) to the right of the blade
(25) looking in the direction in which you are
working, on the side pointing downwards
(provided the workpiece is wide enough) in
order to stop the workpiece from slipping off.
Anleitung_RT_SB_250_U_SPK7:_ 10.02.2012 9:57 Uhr Seite 23
Содержание
- Art nr 43 80 0 i nr 01019 rt sb 1
- Bestimmungsgemäße verwendung 11
- Gerätebeschreibung abb 1 2 8 11
- Lieferumfang 11
- Sicherheitshinweise 11
- Geräuschemissionswerte 12
- Technische daten 12
- Vor inbetriebnahme 12
- Montage 13
- Bedienung 16
- Betrieb 16
- Entsorgung und wiederverwertung 17
- Reinigung wartung und ersatzteilbestellung 17
- Items supplied 19
- Machine layout figures 1 2 8 19
- Proper use 19
- Assembly 20
- Before putting the machine into operation 20
- Important notes 20
- Noise emission values 20
- Technical data 20
- Operation 23
- Maintenance 24
- Operation 24
- Ordering replacement parts 24
- Disposal and recycling 25
- Description de lʼappareil fig 1 2 8 27
- Utilisation conforme à lʼaffectation 27
- Volume de livraison 27
- Caractéristiques techniques 28
- Notes importantes 28
- Valeurs dʼémission de bruit 28
- Avant la mise en service 29
- Montage 29
- Commande 32
- Maintenance 33
- Service 33
- Commande de pièces de rechange 34
- Mise au rebut et recyclage 34
- Descrizione dellʼutensile fig 1 2 8 36
- Elementi forniti 36
- Uso corretto 36
- Avvertenze importanti 37
- Caratteristiche tecniche 37
- Prima della messa in esercizio 37
- Valori di emissione dei rumori 37
- Montaggio 38
- Esercizio 41
- Manutenzione 42
- Ordinazione dei pezzi di ricambio 42
- Smaltimento e riciclaggio 42
- Beskrivning av maskinen bild 1 2 8 44
- Leveransomfattning 44
- Ändamålsenlig användning 44
- Bulleremissionsvärden 45
- Före användning 45
- Montering 45
- Tekniska data 45
- Viktiga anvisningar 45
- Använda sågen 48
- Reservdelsbeställning 49
- Skrotning och återvinning 49
- Underhåll 49
- Irroita verkkopistoke kaikkien korjaus ja huoltotoimien ajaksi 50
- Laitteen kuvaus kuvat 1 2 8 51
- Määräysten mukainen käyttö 51
- Toimituksen laajuus 51
- Ennen käyttöönottoa 52
- Melunpäästöarvot 52
- Tekniset tiedot 52
- Tärkeitä ohjeita 52
- Asennus 53
- Käyttö 55
- Käyttö 56
- Huolto 57
- Käytöstäpoisto ja uusiokäyttö 57
- Varaosien tilaus 57
- 108 ec 58
- 14 ec_2005 88 ec 58
- 32 ec_2009 125 ec 58
- 396 ec_2009 142 ec 58
- 404 ec_2009 105 ec 58
- 686 ec_96 58 ec 58
- Anleitung_rt_sb_250_u_spk7 _ 10 2 012 9 57 uhr seite 58 58
- Annex iv 58
- Annex v annex vi 58
- Bandsäge rt sb 250 u einhell 58
- Isc gmbh eschenstraße 6 d 94405 landau isar 58
- Konformitätserklärung 58
- Landau isar den 07 2 012 58
- Standard references en 61029 1 en 61029 2 5 en 55014 1 en 55014 2 en 61000 3 2 en 61000 3 3 58
- Anleitung_rt_sb_250_u_spk7 _ 10 2 012 9 57 uhr seite 61 61
- T guarantee certificate 62
- P bulletin de garantie 63
- C certificato di garanzia 64
- U garantibevis 65
- Q takuutodistus 66
- Isc gmbh eschenstraße 6 94405 landau isar deutschland 67
- K garan tieurkunde 67
- Anleitung_rt_sb_250_u_spk7 _ 10 2 012 9 57 uhr seite 68 68
- Service hotline 01805 011 843 www isc gmbh info mo fr 8 00 18 00 uhr 68
Похожие устройства
- Binatone SI-4060 Инструкция по эксплуатации
- Einhell BT-SS 405 E Инструкция по эксплуатации
- Binatone SI-4022 Инструкция по эксплуатации
- Einhell RT-SS 120 L Инструкция по эксплуатации
- Binatone SI-4020 Инструкция по эксплуатации
- Einhell BT-SP 1300 Инструкция по эксплуатации
- Binatone SI-4016 Инструкция по эксплуатации
- Einhell RT-SP 260 D Инструкция по эксплуатации
- Binatone SI-4024 Инструкция по эксплуатации
- Einhell RT-SP 260 Инструкция по эксплуатации
- Binatone SI-2500 Инструкция по эксплуатации
- Einhell RT-VE 550 A Инструкция по эксплуатации
- Binatone SI-2510 Инструкция по эксплуатации
- Einhell BT-WW 1000 Инструкция по эксплуатации
- Binatone SI-2610 Инструкция по эксплуатации
- Einhell BT-US 400 Инструкция по эксплуатации
- Binatone SI-2600 Инструкция по эксплуатации
- Binatone SI-2550 Инструкция по эксплуатации
- Einhell BT-LS 65 U Инструкция по эксплуатации
- Einhell BT-LS 810 DB Инструкция по эксплуатации