![Einhell RT-SB 250 U Инструкция по эксплуатации онлайн [22/68] 74043](/img/pdf.png)
Einhell RT-SB 250 U Инструкция по эксплуатации онлайн [22/68] 74043
![Einhell RT-SB 250 U Инструкция по эксплуатации онлайн [22/68] 74043](/views2/1079469/page22/bg16.png)
7.5 Adjusting the blade guide (Fig. 29-31)
Whenever you change the blade you must reset both
the support bearings (30 + 31) and the guide bearings
(32 + 29).
Undo the fasteners (13) and open the left side
cover (12).
7.5.1. Upper support bearing (Fig. 29-31)
Undo the screw (33).
Move the support bearing (30) so that it is
almost touching the blade (25). There should be
a gap of approx. 0.5 mm.
Re-tighten the screw (33).
7.5.2. Setting the lower support bearing (31)
(Figure 29/31)
Disassemble the saw table (15).
Disassemble the support bearing cover (39).
Adjust in the same way that the upper support
bearing was adjusted.
The blade (25) is only supported by the support
bearings (30 + 31) during cutting. When idle the
blade should not touch the ball bearings.
7.5.3. Setting the upper guide bearings (28)
(Figure 29-31)
Undo the screw (35).
Move the upper blade guide (11) so that there is a
gap of approx. 1 mm between the front edge of
the guide bearings (28) and the gullet of the blade
in front.
Re-tighten the screw (37).
CAUTION! The blade will be rendered useless if
the teeth touch the guide bearings while the
blade is running.
Undo the screws (37)
Move the two guide bearings (28) towards the
blade so that there is a gap of approx. 0.5 mm
between the guide bearings (28) and the blade
(25). (The blade must not jam.)
Re-tighten the screws (35).
Turn the upper blade pulley (8) several times in
a clockwise direction.
Check the setting of the guide bearings (28)
again and re-adjust if necessary.
7.5.4. Setting the lower guide bearings (29)
(Figure 30)
앬 Disassemble the saw table (15) (see 7.2).
앬 Undo the screw (40)
앬 Move the mount (49) of the guide bearings (29)
so that there is a gap of approx. 1 mm between
the front edge of the guide bearings (29) and the
gullet of the blade in front.
앬 Re-tighten the screw (40).
앬 IMPORTANT! The blade will be rendered
useless if the teeth touch the guide bearings
while the blade is running.
앬 Undo the screws (38)
앬 Move the guide bearings (29) towards the blade
so that there is a gap of max. 0.5 mm between
the guide bearings (29) and the blade (25). (The
blade must not jam.)
앬 Re-tighten the screws (38).
앬 Turn the lower blade pulley (7) several times in
clockwise direction.
앬 Check the setting of the guide bearings (29)
again and re-adjust if necessary.
7.6 Adjusting the upper blade guide (11)
(Fig. 1/32)
Undo the fixing handle (20).
Lower the blade guide (11) as close as possible
to the workpiece to be cut (the gap should be
approx. 2-3 mm).
Re-tighten the fixing handle (20).
Check the setting before each cut and re-adjust
if necessary.
7.7 Adjusting the saw table (15) to 90°
(Fig. 26,33)
Move the upper blade guide (11) to the top.
Undo the fixing handle (18).
Set the angle (d) between the blade (25) and the
table (15).
Tilt the saw table (15) by turning it so that the
angle between it and the blade (25) is precisely
90°.
Re-tighten the fixing handle (18).
Undo the screw (52) of the pointer of the dial
scale (16), set the pointer to exactly 0° and
tighten the screw (52) again.
No bracket included.
7.8 Selecting the blade
The blade supplied with the bandsaw is designed for
all-purpose use. When you select a blade you should
have regard to the following criteria:
Use a narrow blade to cut tighter radii than you
can with a wider blade.
Wide blades are used to saw straight cuts. This
is particularly important in cutting wood because
the blade has a tendency to follow the grain of
the wood and thereby deviate easily from the
cutting line.
Finely toothed blades provide smoother cuts but
are slower than coarse blades.
Important: Never use warped or lacerated blades!
22
GB
Anleitung_RT_SB_250_U_SPK7:_ 10.02.2012 9:57 Uhr Seite 22
Содержание
- Art nr 43 80 0 i nr 01019 rt sb 1
- Bestimmungsgemäße verwendung 11
- Gerätebeschreibung abb 1 2 8 11
- Lieferumfang 11
- Sicherheitshinweise 11
- Geräuschemissionswerte 12
- Technische daten 12
- Vor inbetriebnahme 12
- Montage 13
- Bedienung 16
- Betrieb 16
- Entsorgung und wiederverwertung 17
- Reinigung wartung und ersatzteilbestellung 17
- Items supplied 19
- Machine layout figures 1 2 8 19
- Proper use 19
- Assembly 20
- Before putting the machine into operation 20
- Important notes 20
- Noise emission values 20
- Technical data 20
- Operation 23
- Maintenance 24
- Operation 24
- Ordering replacement parts 24
- Disposal and recycling 25
- Description de lʼappareil fig 1 2 8 27
- Utilisation conforme à lʼaffectation 27
- Volume de livraison 27
- Caractéristiques techniques 28
- Notes importantes 28
- Valeurs dʼémission de bruit 28
- Avant la mise en service 29
- Montage 29
- Commande 32
- Maintenance 33
- Service 33
- Commande de pièces de rechange 34
- Mise au rebut et recyclage 34
- Descrizione dellʼutensile fig 1 2 8 36
- Elementi forniti 36
- Uso corretto 36
- Avvertenze importanti 37
- Caratteristiche tecniche 37
- Prima della messa in esercizio 37
- Valori di emissione dei rumori 37
- Montaggio 38
- Esercizio 41
- Manutenzione 42
- Ordinazione dei pezzi di ricambio 42
- Smaltimento e riciclaggio 42
- Beskrivning av maskinen bild 1 2 8 44
- Leveransomfattning 44
- Ändamålsenlig användning 44
- Bulleremissionsvärden 45
- Före användning 45
- Montering 45
- Tekniska data 45
- Viktiga anvisningar 45
- Använda sågen 48
- Reservdelsbeställning 49
- Skrotning och återvinning 49
- Underhåll 49
- Irroita verkkopistoke kaikkien korjaus ja huoltotoimien ajaksi 50
- Laitteen kuvaus kuvat 1 2 8 51
- Määräysten mukainen käyttö 51
- Toimituksen laajuus 51
- Ennen käyttöönottoa 52
- Melunpäästöarvot 52
- Tekniset tiedot 52
- Tärkeitä ohjeita 52
- Asennus 53
- Käyttö 55
- Käyttö 56
- Huolto 57
- Käytöstäpoisto ja uusiokäyttö 57
- Varaosien tilaus 57
- 108 ec 58
- 14 ec_2005 88 ec 58
- 32 ec_2009 125 ec 58
- 396 ec_2009 142 ec 58
- 404 ec_2009 105 ec 58
- 686 ec_96 58 ec 58
- Anleitung_rt_sb_250_u_spk7 _ 10 2 012 9 57 uhr seite 58 58
- Annex iv 58
- Annex v annex vi 58
- Bandsäge rt sb 250 u einhell 58
- Isc gmbh eschenstraße 6 d 94405 landau isar 58
- Konformitätserklärung 58
- Landau isar den 07 2 012 58
- Standard references en 61029 1 en 61029 2 5 en 55014 1 en 55014 2 en 61000 3 2 en 61000 3 3 58
- Anleitung_rt_sb_250_u_spk7 _ 10 2 012 9 57 uhr seite 61 61
- T guarantee certificate 62
- P bulletin de garantie 63
- C certificato di garanzia 64
- U garantibevis 65
- Q takuutodistus 66
- Isc gmbh eschenstraße 6 94405 landau isar deutschland 67
- K garan tieurkunde 67
- Anleitung_rt_sb_250_u_spk7 _ 10 2 012 9 57 uhr seite 68 68
- Service hotline 01805 011 843 www isc gmbh info mo fr 8 00 18 00 uhr 68
Похожие устройства
- Binatone SI-4060 Инструкция по эксплуатации
- Einhell BT-SS 405 E Инструкция по эксплуатации
- Binatone SI-4022 Инструкция по эксплуатации
- Einhell RT-SS 120 L Инструкция по эксплуатации
- Binatone SI-4020 Инструкция по эксплуатации
- Einhell BT-SP 1300 Инструкция по эксплуатации
- Binatone SI-4016 Инструкция по эксплуатации
- Einhell RT-SP 260 D Инструкция по эксплуатации
- Binatone SI-4024 Инструкция по эксплуатации
- Einhell RT-SP 260 Инструкция по эксплуатации
- Binatone SI-2500 Инструкция по эксплуатации
- Einhell RT-VE 550 A Инструкция по эксплуатации
- Binatone SI-2510 Инструкция по эксплуатации
- Einhell BT-WW 1000 Инструкция по эксплуатации
- Binatone SI-2610 Инструкция по эксплуатации
- Einhell BT-US 400 Инструкция по эксплуатации
- Binatone SI-2600 Инструкция по эксплуатации
- Binatone SI-2550 Инструкция по эксплуатации
- Einhell BT-LS 65 U Инструкция по эксплуатации
- Einhell BT-LS 810 DB Инструкция по эксплуатации