Home
Главная
Soler&Palau
HTB 90 RC
Руководство по эксплуатации Страница: 13

Soler&Palau HTB 90 RC [13/40] Problem solving

MAINTENANCE

1.- Periodic cleaning is the only maintenance required.

2.- Clean the fan using a soft brush or soft cloth to avoid damaging the ﬁnish.

3.- When carrying out maintenance work, do not use the fan blades as a support as they

could become unbalanced and so increase the vibration of the fan.

4.- Do not use abrasive cleaning agents as these could damage the ﬁnish of the fan.

5.- Do not use water when cleaning the fan as this could cause damage to the motor and

deform the fan blades.

IMPORTANT: Before carrying out any maintenance work on the fan, ensure that it is

disconnected from the mains electrical supply.

PROBLEM SOLVING

IMPORTANT: Before working on the fan ensure that it is disconnected from the mains electricity

supply.

Problems Possible cause Suggested solution

Fan does not start

Fan sounds noisy

1. Blown fuse or circuit breaker.

2. Loose connections to the

mains supply

3. Fan blades not attached to

fan.

4. Loose screws.

5. Loose screws between fan

blades and motor housing.

6. Fan blades not seated pro-

perly.

7. Support plate not securely

ﬁtted to ceiling.

8. Fan blades out of balance.

1. Check fuses or circuit breaker.

2. Tighten connections

3. Fit blades before starting fan.

4. Check all fan screws for

tightness.

5. Check fan blade screws

for tightness. Tighten if

necessary.

6. Check the fan blades sit

snugly

in the motor housing

and with the same angle of

inclination.

7. Check ceiling support

screws.

8. Change the position of some

of the blades.

Fitting to a wooden beam

Four screws (H) are supplied together with safety washer’s (I) for ﬁtting the support plate (A) to a

wooden beam. The holes for the screws should not be of greater diameter than the diameter of the

screw. Ensure that the wooden beam is able to support the weight of the moving fan (minimum

25/40 Kg.) (Fig.4)

ASSEMBLY OF THE FAN

IMPORTANT: If you installing more than one fan, ensure that you do not mix the fan blade sets, even

though they are from the same ceiling fan model.

1.- Fit the blades with the angles as shown in ﬁgure 5

2.- Fit the blades (C) to the motor assembly and support (B) using the screws (D) and the safety

washers (E). Do not forget to use the felt protection washers between the blade and the motor

assembly to avoid possible noise. Repeat this process with the remaining blades. (Fig.6)

IMPORTANT: Be careful not to support yourself on the fan blades, as these could then become

unbalanced and cause vibration or shaking of the fan.

3.- Loosen the screws situated in the base of the decorative canopy to allow easier access to the

anchorage point and electrical connectors. Hang the motor and support assembly (B) from the hook

on the support plate (A) (previously ﬁxed to the ceiling) (Fig.7)

4.- Connect the cables and position them correctly. The connections and the ﬁtting point can be

hidden using the decorative canopy.

INSTALLATION ELECTRICAL

IMPORTANT SAFETY NOTICE: Before installation, ensure that the electrical supply is disconnected

at the mains junction / fuse box.

- The airﬂow direction can be changed depending upon the wiring connection conﬁguration in

accordance with (Fig.8)

- All products are supplied, factory wired, for a downward airﬂow conﬁguration.

- If the airﬂow direction is required to be changed on a frequent basis, then an airﬂow direction

switch should be installed as a separate additional accessory (Fig.9)

IMPORTANT: Before changing the direction of ariﬂow, the fan blades must have completely stopped

turning after switching the unit to the off position.

OPERATION INSTRUCTIONS

1. – The speed regulator has four positions.

0 .........OFF

1 ......... High speed

2 ......... Medium speed

3 ......... Low speed

1110

Soler&Palau HTB 90 RC [13/40] Problem solving

Содержание

Похожие устройства