Home
Главная
Kramer
Коммутаторы / Step-In
DIP-20
Руководства по эксплуатации Страница: 13

Kramer DIP-20 [13/81] Connecting the dip 20 automatic video

DIP-20 - Connecting the DIP-20 Automatic Video Switcher

5 Connecting the DIP-20 Automatic Video

Switcher

Always switch off the power to each device before connecting it to

your DIP-20. After connecting your DIP-20, connect the power to

each of them and then switch on the power to each device.

Figure 3: Connecting the DIP-20

Содержание

Automatic video switcher 1
User manual 1
Contents 4
Figures 5
Introduction 6
Achieving the best performance 7
Getting started 7
Safety instructions 7
Recycling kramer products 8
Shielded twisted pair unshielded twisted pair 8
Overview 9
About hdbaset technology 10
Defining the automatic video switcher 11
Figure 1 defines the front panel of the dip 20 11
Figure 2 defines the rear panel of the dip 20 12
Connecting the dip 20 automatic video 13
Connecting the dip 20 automatic video switcher 13
Switcher 13
Closure switches 15
Connecting the remote control switches 15
Figure 4 illustrates the connections from the terminal block to the contact 15
Terminal block on the rear panel of the dip 20 to control the device 15
You can connect remote momentary contact contact closure switches to the 15
Connectors 16
This section defines the tp pinout using a straight pin to pin cable with rj 45 16
Wiring the rj 45 connectors 16
Input selection 17
Principles of operation 17
Another input is automatically selected when an input cable is removed there 18
Audio is handled 18
Audio signal control 18
Both timeouts are configurable see section 8 18
But the cable is not removed there is a default delay ten seconds for video 18
Display is connected analog audio is output even in the absence of a video 18
In both last connected and priority modes when the input signal sync is lost 18
Is a delay before automatic switching takes place 18
Not applicable to the pc input and five seconds for analog audio before 18
Note analog audio is not output when there is no display connected if a 18
Pattern in conjunction with the external analog audio in signal 18
Signal 18
Signal loss and unplugged cable timeouts 18
The following table describes which audio signal is embedded in the output 18
The option dip switches 3 and 4 see section 8 control the manner in which 18
When there is an audio signal but no video signal the output is a black video 18
Vga phase shift 19
Analog audio output volume control 20
Locking the edid 20
Operating the dip 20 20
Resetting the dip 20 20
Audio switching selection 22
Configuring the dip 20 22
Functions a switch that is down is on a switch that is up is off by default all 22
Implement the change 22
Note after changing a dip switch you must power cycle the device to 22
Setting the configuration dip switch 22
The 4 way dip switch provides the ability to configure a number of device 22
The switches are up off 22
Video switching selection 22
Using the step in feature 23
Video switching timeouts 23
Browsing the dip 20 web pages 24
Operating the dip 20 remotely using the 24
Operating the dip 20 remotely using the web pages 24
Web pages 24
The areas of the main switching page are described in the following table 26
The upload save configuration facility 27
The switching page 28
The switching page lets you select a video input manually and adjust the audio 28
Volume 28
The device settings page 29
Browse to the required file 31
Click ok 31
Click ok to continue or cancel to exit the procedure 31
Click start upgrade 31
Click the browse button 31
Click the factory reset button 31
Do not interrupt the process or the dip 20 may be damaged 31
On completion the success message is displayed 31
Select the required file and click open 31
The confirmation message is displayed 31
The firmware file is loaded and a progress bar is displayed 31
The firmware file name is displayed in the firmware upgrade page 31
The firmware is upgraded 31
The progress message is displayed 31
The windows browser opens 31
To reset the dip 20 to factory default parameters 31
To upgrade the firmware 31
When the process is complete reboot the device 31
The video and audio settings page 32
The video and audio settings page lets you modify the video audio and 32
Timeout parameters 32
The authentication page 33
The authentication page lets you assign or change logon authentication details 33
Changes on the device caused by outputs being exchanged click refresh to 34
Default edid 34
Edid data file 34
Following sources 34
From this page you can also lock the edid on each input independently 34
Note the display is not updated automatically when the status of an edid 34
Output 34
The edid page 34
The edid page lets you copy edid data to either or both of the inputs from the 34
Update the display see item 11 in the following table 34
All selected input buttons change color and the edid summary 35
Check box 35
Click a destination input or select both inputs by checking the inputs 35
Click ok 35
Click the copy button 35
Click the source button from which to read the edid default output 35
Electronics ltd company details 35
Information reflects the selection and edid data 35
Input or edid file 35
Is copied to the selected input s 35
Selection and edid data 35
The about us page 35
The button changes color and the edid summary information reflects the 35
The dip 20 about us page displays the web page version and kramer 35
The edid was copied success message is displayed and the edid data 35
To copy edid data from a source to one or both inputs 35
Technical specifications 37
Default ip parameters 38
Default logon credentials 38
Supported resolutions 38
Dip 20 technical specifications 39
Resolution refresh rate 39
Resolution refresh rate hz 39
Default edid 40
Each input on the dip 20 is loaded with a factory default edid 40
Dip 20 default edid 41
Dip 20 default edid 37 42
Pc uxga 42
Dip 20 default edid 43
Command string 44
Device message format 44
Host message format 44
Kramer protocol 3000 syntax 44
Protocol 3000 44
Simple command 44
Command terms 45
Device long response 45
Chaining commands 46
Command forms 46
Entering commands 46
Characters 47
Maximum string length 47
System commands 47
File system commands 58
0 authentication commands 62
1 switching routing commands 65
2 video commands 66
3 audio commands 67
4 communication commands 70
5 edid handling commands 74
6 factory commands 78
7 layer 79
8 data source and destination ports 79
9 video audio signal changes 79
Safety warning 81

Kramer DIP-20 [13/81] Connecting the dip 20 automatic video

Содержание

Похожие устройства