![Kramer DIP-20 [43/81] Dip 20 default edid](/img/pdf.png)
Kramer DIP-20 [43/81] Dip 20 default edid
![Kramer DIP-20 [43/81] Dip 20 default edid](/views2/1152407/page43/bg2b.png)
38
DIP-20 - Default EDID
Basic audio.............. Supported
YCbCr 4:4:4.............. Supported
YCbCr 4:2:2.............. Supported
Native formats........... 1
Detailed timing #1....... 1920x1080p at 60Hz (16:10)
Modeline............... "1920x1080" 148.500 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync
Detailed timing #2....... 1920x1080i at 60Hz (16:10)
Modeline............... "1920x1080" 74.250 1920 2008 2052 2200 1080 1084 1094 1124 interlace +hsync
+vsync
Detailed timing #3....... 1280x720p at 60Hz (16:10)
Modeline............... "1280x720" 74.250 1280 1390 1430 1650 720 725 730 750 +hsync +vsync
Detailed timing #4....... 720x480p at 60Hz (16:10)
Modeline............... "720x480" 27.000 720 736 798 858 480 489 495 525 -hsync -vsync
CE audio data (formats supported)
LPCM 2-channel, 16/20/24 bit depths at 32/44/48 kHz
CE video identifiers (VICs) - timing/formats supported
1920 x 1080p at 60Hz - HDTV (16:9, 1:1)
1920 x 1080i at 60Hz - HDTV (16:9, 1:1)
1280 x 720p at 60Hz - HDTV (16:9, 1:1) [Native]
720 x 480p at 60Hz - EDTV (16:9, 32:27)
720 x 480p at 60Hz - EDTV (4:3, 8:9)
720 x 480i at 60Hz - Doublescan (16:9, 32:27)
720 x 576i at 50Hz - Doublescan (16:9, 64:45)
640 x 480p at 60Hz - Default (4:3, 1:1)
NB: NTSC refresh rate = (Hz*1000)/1001
CE vendor specific data (VSDB)
IEEE registration number. 0x000C03
CEC physical address..... 1.0.0.0
Maximum TMDS clock....... 165MHz
CE speaker allocation data
Channel configuration.... 2.0
Front left/right......... Yes
Front LFE................ No
Front center............. No
Rear left/right.......... No
Rear center.............. No
Front left/right center.. No
Rear left/right center... No
Rear LFE................. No
Report information
Date generated........... 09/08/2015
Software revision........ 2.60.0.972
Data source.............. File
Operating system......... 6.1.7601.2.Service Pack 1
Raw data
00,FF,FF,FF,FF,FF,FF,00,2D,B2,00,12,00,00,00,00,FF,19,01,03,6E,34,20,78,EE,B3,25,AC,51,30,B4,26,
10,50,54,FF,FF,80,81,8F,81,99,A9,40,61,59,45,59,31,59,71,4A,81,40,01,1D,00,72,51,D0,1E,20,6E,28,
55,00,07,44,21,00,00,1E,00,00,00,FD,00,38,4C,1E,53,11,00,0A,20,20,20,20,20,20,00,00,00,FC,00,41,
56,53,2D,33,32,20,20,20,20,20,20,20,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,C6,
02,03,1B,F1,23,09,07,07,48,10,05,84,03,02,07,16,01,65,03,0C,00,10,00,83,01,00,00,02,3A,80,18,71,
38,2D,40,58,2C,45,00,07,44,21,00,00,1E,01,1D,80,18,71,1C,16,20,58,2C,25,00,07,44,21,00,00,9E,01,
1D,00,72,51,D0,1E,20,6E,28,55,00,07,44,21,00,00,1E,8C,0A,D0,8A,20,E0,2D,10,10,3E,96,00,07,44,21,
00,00,18,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,47
Содержание
- Automatic video switcher 1
- User manual 1
- Contents 4
- Figures 5
- Introduction 6
- Achieving the best performance 7
- Getting started 7
- Safety instructions 7
- Recycling kramer products 8
- Shielded twisted pair unshielded twisted pair 8
- Overview 9
- About hdbaset technology 10
- Defining the automatic video switcher 11
- Figure 1 defines the front panel of the dip 20 11
- Figure 2 defines the rear panel of the dip 20 12
- Connecting the dip 20 automatic video 13
- Connecting the dip 20 automatic video switcher 13
- Switcher 13
- Closure switches 15
- Connecting the remote control switches 15
- Figure 4 illustrates the connections from the terminal block to the contact 15
- Terminal block on the rear panel of the dip 20 to control the device 15
- You can connect remote momentary contact contact closure switches to the 15
- Connectors 16
- This section defines the tp pinout using a straight pin to pin cable with rj 45 16
- Wiring the rj 45 connectors 16
- Input selection 17
- Principles of operation 17
- Another input is automatically selected when an input cable is removed there 18
- Audio is handled 18
- Audio signal control 18
- Both timeouts are configurable see section 8 18
- But the cable is not removed there is a default delay ten seconds for video 18
- Display is connected analog audio is output even in the absence of a video 18
- In both last connected and priority modes when the input signal sync is lost 18
- Is a delay before automatic switching takes place 18
- Not applicable to the pc input and five seconds for analog audio before 18
- Note analog audio is not output when there is no display connected if a 18
- Pattern in conjunction with the external analog audio in signal 18
- Signal 18
- Signal loss and unplugged cable timeouts 18
- The following table describes which audio signal is embedded in the output 18
- The option dip switches 3 and 4 see section 8 control the manner in which 18
- When there is an audio signal but no video signal the output is a black video 18
- Vga phase shift 19
- Analog audio output volume control 20
- Locking the edid 20
- Operating the dip 20 20
- Resetting the dip 20 20
- Audio switching selection 22
- Configuring the dip 20 22
- Functions a switch that is down is on a switch that is up is off by default all 22
- Implement the change 22
- Note after changing a dip switch you must power cycle the device to 22
- Setting the configuration dip switch 22
- The 4 way dip switch provides the ability to configure a number of device 22
- The switches are up off 22
- Video switching selection 22
- Using the step in feature 23
- Video switching timeouts 23
- Browsing the dip 20 web pages 24
- Operating the dip 20 remotely using the 24
- Operating the dip 20 remotely using the web pages 24
- Web pages 24
- The areas of the main switching page are described in the following table 26
- The upload save configuration facility 27
- The switching page 28
- The switching page lets you select a video input manually and adjust the audio 28
- Volume 28
- The device settings page 29
- Browse to the required file 31
- Click ok 31
- Click ok to continue or cancel to exit the procedure 31
- Click start upgrade 31
- Click the browse button 31
- Click the factory reset button 31
- Do not interrupt the process or the dip 20 may be damaged 31
- On completion the success message is displayed 31
- Select the required file and click open 31
- The confirmation message is displayed 31
- The firmware file is loaded and a progress bar is displayed 31
- The firmware file name is displayed in the firmware upgrade page 31
- The firmware is upgraded 31
- The progress message is displayed 31
- The windows browser opens 31
- To reset the dip 20 to factory default parameters 31
- To upgrade the firmware 31
- When the process is complete reboot the device 31
- The video and audio settings page 32
- The video and audio settings page lets you modify the video audio and 32
- Timeout parameters 32
- The authentication page 33
- The authentication page lets you assign or change logon authentication details 33
- Changes on the device caused by outputs being exchanged click refresh to 34
- Default edid 34
- Edid data file 34
- Following sources 34
- From this page you can also lock the edid on each input independently 34
- Note the display is not updated automatically when the status of an edid 34
- Output 34
- The edid page 34
- The edid page lets you copy edid data to either or both of the inputs from the 34
- Update the display see item 11 in the following table 34
- All selected input buttons change color and the edid summary 35
- Check box 35
- Click a destination input or select both inputs by checking the inputs 35
- Click ok 35
- Click the copy button 35
- Click the source button from which to read the edid default output 35
- Electronics ltd company details 35
- Information reflects the selection and edid data 35
- Input or edid file 35
- Is copied to the selected input s 35
- Selection and edid data 35
- The about us page 35
- The button changes color and the edid summary information reflects the 35
- The dip 20 about us page displays the web page version and kramer 35
- The edid was copied success message is displayed and the edid data 35
- To copy edid data from a source to one or both inputs 35
- Technical specifications 37
- Default ip parameters 38
- Default logon credentials 38
- Supported resolutions 38
- Dip 20 technical specifications 39
- Resolution refresh rate 39
- Resolution refresh rate hz 39
- Default edid 40
- Each input on the dip 20 is loaded with a factory default edid 40
- Dip 20 default edid 41
- Dip 20 default edid 37 42
- Pc uxga 42
- Dip 20 default edid 43
- Command string 44
- Device message format 44
- Host message format 44
- Kramer protocol 3000 syntax 44
- Protocol 3000 44
- Simple command 44
- Command terms 45
- Device long response 45
- Chaining commands 46
- Command forms 46
- Entering commands 46
- Characters 47
- Maximum string length 47
- System commands 47
- File system commands 58
- 0 authentication commands 62
- 1 switching routing commands 65
- 2 video commands 66
- 3 audio commands 67
- 4 communication commands 70
- 5 edid handling commands 74
- 6 factory commands 78
- 7 layer 79
- 8 data source and destination ports 79
- 9 video audio signal changes 79
- Safety warning 81
Похожие устройства
- Kramer DIP-20 Инструкция по установке
- Kramer DIP-30 Инструкция по установке
- Kramer DIP-30 Руководства по эксплуатации
- Kramer VP-81SIDN Руководства по эксплуатации
- Razer Orochi 2013 (RZ01-00820100-R3G1) Инструкция по эксплуатации
- Razer Nabu X White (RZ15-01290200-R3G1) Инструкция по эксплуатации
- Razer Firefly (RZ02-01350100-R3M1) Инструкция по эксплуатации
- Razer Goliathus 2013 Speed Extended(RZ02-01070400-R3M1) Инструкция по эксплуатации
- Kramer SID-DP Руководства по эксплуатации
- Kramer SID-VGA Руководства по эксплуатации
- Kramer SID-H Руководства по эксплуатации
- Kramer SID-DVI Руководства по эксплуатации
- Kramer SID-X1N Руководства по эксплуатации
- Kramer SID-X2N Документация
- Kramer SID-X2N Руководства по эксплуатации
- Kramer SID-X3N Руководства по эксплуатации
- Kramer VS-41USB Руководства по эксплуатации
- Kramer VS-401USB Руководства по эксплуатации
- Kramer VS-801USB Руководства по эксплуатации
- Kramer VS-121HC Руководства по эксплуатации