![Supermicro sys-6017r-tdf [10/106] 2 serverboard features](/img/pdf.png)
Supermicro sys-6017r-tdf [10/106] 2 serverboard features
![Supermicro sys-6017r-tdf [10/106] 2 serverboard features](/views2/1190403/page10/bga.png)
1-2
SUPERSERVER 6017R-TDF User's Manual
1-2 Serverboard Features
At the heart of the SuperServer 6017R-TDF lies the X9DRD-iF, a dual processor
serverboard based on Intel's C600 chipset. Below are the main features of the
X9DRD-iF (see Figure 1-1 for a block diagram of the chipset).
Processors
The X9DRD-iF supports single or dual Intel
®
Xeon
®
E5-2600 Series processors in
LGA 2011 sockets. Please refer to the serverboard description pages on our web
site for a complete listing of supported processors.
Memory
The X9DRD-iF has eight DIMM sockets that can support up to 256 GB of regis-
tered DDR3-1600/1333/1066/800 RDIMM memory. Please refer to Chapter 5 for
installing memory.
SATA
An on-chip SATA controller is integrated into the X9DRD-iF to provide a six-port,
Serial ATA subsystem, which is RAID 0, 1, 5 and 10 supported. Two of the ports
support SATA 3.0, while the other four are SATA 2.0 ports. The SATA drives are
hot-swappable units.
Four additional SCU SATA ports are also provided on the X9DRD-iF.
Note: The operating system you use must have RAID support to enable the hot-
swap capability and RAID function of the SATA drives. Documentation on RAID
setup guidelines can be found on our web site.
I/O Ports
The color-coded I/O ports include one COM port, a VGA (monitor) port, four USB
2.0 ports and two gigabit Ethernet ports. A dedicated IPMI LAN port is also included.
Onboard Graphics
The X9DRD-iF provides onboard grpahics with a Matrox G200eW graphics con-
troller.
Содержание
- Manual revision 1 release date march 19 2012 2
- Printed in the united states of america 2
- Warning handling of lead solder materials used in this product may expose you to lead a chemical known to the state of california to cause birth defects and other repro ductive harm 2
- About this manual 3
- Chapter 1 introduction 3
- Chapter 2 server installation 3
- Chapter 3 system interface 3
- Manual organization 3
- Preface 3
- Appendix a bios error beep codes 4
- Appendix b system specifi cations 4
- Chapter 4 system safety 4
- Chapter 5 advanced serverboard setup 4
- Chapter 6 advanced chassis setup 4
- Chapter 7 bios 4
- Chapter 1 introduction 6
- Chapter 2 server installation 6
- Chapter 3 system interface 6
- Table of contents 6
- Chapter 4 system safety 7
- Chapter 5 advanced serverboard setup 7
- Chapter 6 advanced chassis setup 7
- Appendix a bios error beep codes 8
- Appendix b system specifi cations 8
- Chapter 7 bios 8
- 1 overview 9
- Chapter 1 9
- Introduction 9
- 2 serverboard features 10
- I o ports 10
- Memory 10
- Onboard graphics 10
- Processors 10
- 3 server chassis features 11
- Control panel 11
- Cooling system 11
- Sata subsystem 11
- System power 11
- Ddr3 dimm ddr3 dimm 12
- I350 glan 12
- Jpcie1 pcie 3 x8 jpcie2 pcie 3 x8 12
- Lpc usb 12
- Processor 1 left 12
- Processor 2 right 12
- Rtl8201f 12
- Ssb pch c602 12
- Tpm hdr 12
- W25q128 12
- W83527 12
- 4 contacting supermicro 13
- Asia pacifi c 13
- Europe 13
- Headquarters 13
- 1 overview 15
- 2 unpacking the system 15
- 3 preparing for setup 15
- Chapter 2 15
- Server installation 15
- Choosing a setup location 16
- Rack precautions 16
- Server precautions 16
- Warnings and precautions 16
- Ambient operating temperature 17
- Circuit overloading 17
- Mechanical loading 17
- Rack mounting considerations 17
- Reduced airfl ow 17
- Reliable ground 17
- 4 rack mounting instructions 18
- Identifying the sections of the rack rails 18
- Inner rail extension 19
- Installing the chassis into a telco rack 23
- 1 overview 25
- 2 control panel buttons 25
- Chapter 3 25
- System interface 25
- 3 control panel leds 26
- Overheat fan fail 26
- 4 hard drive carrier leds 27
- 1 electrical safety precautions 29
- Chapter 4 29
- System safety 29
- 2 general safety precautions 30
- 3 esd precautions 31
- 4 operating precautions 32
- 1 handling the serverboard 33
- Advanced serverboard setup 33
- Chapter 5 33
- Precautions 33
- Unpacking 33
- 2 processor and heatsink installation 34
- Installing an lga 2011 processor 34
- Installing a passive cpu heatsink 37
- Removing the heatsink 37
- 3 connecting cables 38
- Connecting data cables 38
- Connecting power cables 38
- Connecting the control panel 38
- 4 i o ports 39
- All jf1 wires have been bundled into single keyed ribbon cable to simplify their con nection connect one end of this cable to jf1 and the other end to the control panel printed circuit board located just behind the system status leds in the chassis 39
- Backplane i o ports 39
- Chapter 5 advanced serverboard setup 39
- Figure 5 2 front control panel header pins jf1 39
- Figure 5 3 below for the colors and locations of the various i o ports 39
- Figure 5 3 rear panel i o ports 39
- See the connector defi nitions section in this chapter for details and pin descrip tions of jf1 39
- The i o ports are color coded in conformance with the pc 99 specifi cation see 39
- 5 installing memory 40
- Caution 40
- Chapter 5 advanced serverboard setup 41
- Processor and memory module population 41
- Processors and their corresponding memory modules 41
- Rdimm support por on the e5 2600 series processor platform 41
- 6 adding pci cards 42
- 7 serverboard details 43
- Slot3 pci e 3 x8 43
- Slot4 pci e 3 x8 43
- Slot5 pci e 3 x8 43
- Slot6 pci e 3 x16 43
- Slot7 pci e 3 x8 cpu2 43
- X9drd if 43
- X9drd if quick reference 43
- 8 connector defi nitions 45
- A 24 pin main power supply connector jpw1 two 8 pin cpu power con nectors jpw2 3 and one 4 pin power connectors jpw5 are located on the serverboard these power connectors meet the ssi eps 12v specification and must be connected to your power supply to provide adequate power to the system see the table on the right for pin defi nitions 45
- Chapter 5 advanced serverboard setup 45
- Defi nitions 45
- Er is located on pins 19 and 20 of jf1 45
- Hdd led 45
- In addition to the atx main power two 45
- Jpw2 and jpw3 are also required con 45
- Nections see the table on the right for 45
- Nmi button 45
- On the right for pin defi nitions 45
- Pin 12v power connector located at 45
- Pin defi nitions 45
- Pin power connectors 45
- Pins 13 and 14 of jf1 attach a cable here to indicate hdd activity see the table on the right for pin defi nitions 45
- Pins 15 and 16 of jf1 refer to the table 45
- Power connectors 45
- Power led 45
- Refer to the table on the right for pin 45
- The hdd led connection is located on 45
- The non maskable interrupt button head 45
- The power led connection is located on 45
- Case refer to the table on the right for pin defi nitions 46
- Connect an led cable to pins 7 and 46
- Default refer to the tables on the right 46
- Erver 6017r tdf user s manual 46
- For pin defi nitions 46
- Nic1 nic2 led indicators 46
- Of jf1 to use the overheat fan fail 46
- Of overheat fan failure or power failure 46
- Overheat oh fan fail pwr fail uid led 46
- Panel uid led indicator the red led 46
- Power fail and uid led connections 46
- Power fail led 46
- Reset button 46
- Takes precedence over the blue led by 46
- The blue led on pin 8 works as the front 46
- The nic network interface controller led connection for lan port 1 is located on pins 11 and 12 of jf1 and the led connection for lan port 2 is on pins 9 and 10 attach the nic led cables here to display network activity refer to the table on the right for pin defi nitions 46
- The power fail led connection is lo cated on pins 5 and 6 of jf1 refer to the table on the right for pin defi nitions 46
- The red led on pin 7 provides warnings 46
- The reset button connection is located on pins 3 and 4 of jf1 attach it to a hardware reset switch on the computer 46
- 1 usb 2 3 are located on the rear i o 47
- A connector usb6 also supports front 47
- Access support see the table on the right 47
- Are located on the serverboard com1 47
- Chapter 5 advanced serverboard setup 47
- For pin defi nitions 47
- Four universal serial bus ports usb 47
- Is located on the rear i o panel com2 47
- Located close to cpu slot3 provides front 47
- Nc no connection 47
- Panel in addition three usb headers provide four front accessible usb con nections usb 4 5 usb 8 9 one type 47
- Panel usb connection cables are not included see the tables on the right for pin defi nitions 47
- Power button 47
- Serial ports 47
- The power button connection is located on pins 1 and 2 of jf1 momentarily contacting both pins will power on off the system this button can also be confi g ured to function as a suspend button with a setting in the bios see chapter 7 to turn off the power when the system is in suspend mode press the button for 4 seconds or longer refer to the table on the right for pin defi nitions 47
- Two com connections com1 com2 47
- Universal serial bus usb 47
- A chassis intrusion header is located at 48
- A unit identifi er uid switch and two 48
- Both led indicators these uid indicators 48
- Chassis intrusion 48
- Connect a cable to pin 8 on jf1 for the 48
- Erver 6017r tdf user s manual 48
- Ethernet ports 48
- Jl1 on the serverboard attach the ap propriate cable from the chassis to inform you of a chassis intrusion when the chas 48
- Led indicators are provided on the 48
- Next to the vga port on the backplane 48
- Note uid can also be triggered via ipmi 48
- On the serverboard for more information on ipmi please refer to the ipmi user s guide posted on our website http 48
- Panel uid led indicators will turn on 48
- Press the uid switch again to turn off 48
- Press the uid switch both the rear front 48
- Provide easy identifi cation of a system 48
- Serverboard the uid switch is located 48
- Sis is opened 48
- The rear uid led led3 is located next 48
- To the uid switch the control panel 48
- Two ethernet ports lan1 lan2 are located next to the vga port on the i o back panel an ipmi dedicated lan port is also located above the usb0 1 ports this provides a dedicated network con nection for ipmi 2 support these ports accept rj45 type connectors cables 48
- Uid led is located on pins 7 8 of jf1 48
- Uid led on the control panel when you 48
- Unit identifi er switch uid led indicators 48
- Unit that may be in need of service 48
- Www supermicro com 48
- Be used to provide audible indications for 49
- Below for the locations of the internal 49
- Buzzer sp1 49
- Chapter 5 advanced serverboard setup 49
- Close pins 6 7 with a jumper 49
- Fan headers 49
- Internal speaker 49
- Note please use all 3 pin fans or all 4 pin fans on a serverboard do not mix 3 pin fans and 4 pin fans on the same board 49
- On jd1 header pins 1 3 are used for power led indication and pins 4 7 are for the speaker see the tables on the 49
- Power led speaker 49
- Right for pin defi nitions please note that 49
- Right for pin defi nitions refer to the layout 49
- The internal speaker located at sp1 can 49
- The speaker connector pins 4 7 are used with an external speaker if you wish to use the onboard speaker you should 49
- The x9drd if has eight fan headers fan1 fan8 these are all 4 pin fan headers however pins 1 3 are backward compatible with traditional 3 pin fans a fan speed control setting in the bios hardware monitoring section allows the bios to automatically set fan speeds based on the system temperature refer to the table on the right for pin defi nitions 49
- Various beep codes see the table on the 49
- A system management bus header for ipmi 2 is located at jipmb1 connect 50
- An led indicator to provide warnings 50
- C connection on your system 50
- C connector 50
- C connector jp 50
- C1 monitors power 50
- Erver 6017r tdf user s manual 50
- Occurs refer to the tables on right for 50
- Of chassis overheating and fan failure 50
- Overheat led fan fail 50
- Pin defi nitions 50
- Power smb 50
- See the table on the right for pin defi ni tions 50
- Supply fan and system temperatures 50
- The appropriate cable here to use the ipmb 50
- The joh1 header is used to connect 50
- The jtpm1 header is used to connect a trusted platform module tpm available separately from a third party vendor a tpm is a security device that allows en cryption and authentication of hard drives disallowing access if the tpm associated with it is not installed in the system see the table on the right for pin defi nitions 50
- The power system management bus 50
- This led will blink when a fan failure 50
- Trusted platform module header 50
- A disk on module dom power con 51
- Chapter 5 advanced serverboard setup 51
- Defi nitions 51
- Dom pwr connector 51
- F ash memory media attached to a sata 51
- Nc no connection 51
- Nector is located at jds1 this connec 51
- Port see the table on the right for pin 51
- See the table on the right for pin defi ni 51
- Standby power header 51
- T sgpio 0 1 headers 51
- The 5v standby power header is lo cated at jstby1 on the serverboard 51
- Tions you must also have a card with a standby power connector and a cable to use this feature 51
- Tor is used to provide power to auxilliary 51
- Two t sgpio serial link general purpose input output headers are located near the sata connectors on the serverboard these headers are used to communicate with the enclosure management chip in the system see the table on the right for pin defi nitions refer to the board layout below for the locations of the headers 51
- 9 jumper settings 52
- 10 onboard indicators 54
- A bmc heartbeat led is located at ledm1 on the serverboard when 54
- An onboard standby power led is lo 54
- Bmc heartbeat led 54
- Cated at led2 on the serverboard when 54
- Each ethernet port has two leds the yellow led indicates activity when blink ing while the other led may be green amber or off to indicate the speed of the connection see the table on the right for the functions associated with the connec tion speed led 54
- Erver 6017r tdf user s manual 54
- In addition to the lan ports a dedicated 54
- Indicates activity while the green led on 54
- Information 54
- Ipmi dedicated lan 54
- Ipmi lan port is also included on the 54
- Lan1 lan2 leds 54
- Led2 is on the system is running make sure to disconnect the power cable before removing or installing any components 54
- Ledm1 is blinking the bmc is function ing normally see the table at right for more information 54
- Nection see the table at right for more 54
- Onboard standby power led 54
- The left indicates the speed of the con 54
- X9drd if the amber led on the right 54
- 11 sata drive ports 55
- Chapter 5 advanced serverboard setup 55
- Sata ports scu connectors 55
- There are four sata 2 sata2 sata5 and two sata 3 sata0 1 ports located on the x9drd if in addition four scu connectors scu0 3 are also provided on the board see the table on the right for pin defi nitions 55
- 12 installing drivers 56
- Superdoctor iii 57
- 1 static sensitive devices 59
- Advanced chassis setup 59
- Chapter 6 59
- Precautions 59
- 2 control panel 60
- Connect the cable from jf1 on the serverboard to the appropriate header on the 60
- Control panel pcb printed circuit board make sure the red wire plugs into pin 1 on both connectors pull all excess cabling out of the airfl ow path 60
- Erver 6017r tdf manual 60
- Figure 6 1 chassis front and rear views 60
- Terface for details on the leds and the control panel buttons details on jf1 can be found in chapter 5 advanced serverboard setup 60
- The control panel leds inform you of system status see chapter 3 system in 60
- The control panel located on the front of the chassis must be connected to the jf1 connector on the serverboard to provide you with system status indications these wires have been bundled together as a ribbon cable to simplify the connection 60
- 3 system fans 61
- System fan failure 61
- 4 drive bay installation removal 63
- Accessing the drive bays 63
- Removing the front bezel 63
- Sata drive installation 64
- Sata backplane 65
- Sata power cables 65
- Cd rom and floppy drive installation 66
- 5 power supply 67
- Power supply failure 67
- 1 introduction 69
- Chapter 7 69
- How to change the confi guration data 69
- Starting bios setup utility 69
- 2 main setup 70
- Starting the setup utility 70
- 3 advanced setup confi gurations 72
- Boot features 72
- Cpu confi guration 73
- Power confi guration 73
- Socket 1 cpu information socket 2 cpu information 73
- Cpu power management confi guration 76
- Chipset confi guration 78
- Integrated io confi guration 78
- North bridge 78
- Dimm confi guration 79
- Qpi confi guration 79
- South bridge confi guration 81
- Sata confi guration 82
- Scu storage control unit confi guration 83
- Pcie pci pnp confi guration 84
- Serial port 1 confi guration 85
- Super io confi guration 85
- Serial port 2 confi guration 86
- Serial port console redirection 86
- Console redirection settings 87
- Acpi setting 88
- Tpm enable status 89
- Trusted computing available when a tpm device is detected by the bios 89
- Intel me subsystem confi guration 90
- Intel txt lt sx confi guration 90
- Nic confi guration 91
- 3 event logs 92
- Change smbios event log settings 92
- 4 ipmi 94
- System event log 94
- Bmc network confi guration 95
- 5 boot 96
- Delete boot options 96
- 6 security 97
- 7 save exit 98
- Appendix a 101
- Bios error beep codes 101
- Appendix b 103
- Chassis 103
- Chipset 103
- Expansion slots 103
- Memory capacity 103
- Processors 103
- Sata controller 103
- Sata drive bays 103
- Serverboard 103
- System specifi cations 103
- Weight 103
- Operating environment 104
- Power supply 104
- Regulatory compliance 104
- System cooling 104
- System input requirements 104
- Appendix b system specifi cations 105
Похожие устройства
- Supermicro cse-835tq-r800b Инструкция по эксплуатации
- Supermicro x10drh-i-b Инструкция по эксплуатации
- Supermicro sys-6028r-t Инструкция по эксплуатации
- Supermicro x10dai-0 Инструкция по эксплуатации
- Supermicro x10dri-o Инструкция по эксплуатации
- Supermicro x10dai-b Инструкция по эксплуатации
- Supermicro x10drl-i-o Инструкция по эксплуатации
- Supermicro cse-743tq-865b-sq Инструкция по эксплуатации
- Supermicro x10srl-f-o Инструкция по эксплуатации
- Supermicro x10dri-t4+ Инструкция по эксплуатации
- Supermicro x10slh-f-b Инструкция по эксплуатации
- Supermicro cse-732i-500b Инструкция по эксплуатации
- Supermicro cse-732i-865b Инструкция по эксплуатации
- Supermicro cse-826be16-r1k28lpb Инструкция по эксплуатации
- Supermicro cse-733t-500b Инструкция по эксплуатации
- Supermicro x9drl-if-o Инструкция по эксплуатации
- Supermicro cse-733tq-500b Инструкция по эксплуатации
- Supermicro sys-1027r-wrf Инструкция по эксплуатации
- Supermicro sys-5018d-mf Инструкция по эксплуатации
- Supermicro x10sae Инструкция по эксплуатации