![ECS Elitegroup KA1 MVP Руководство пользователя онлайн [11/85] 176068](/img/pdf.png)
ECS Elitegroup KA1 MVP Руководство пользователя онлайн [11/85] 176068
1-6
6. Flash ROM
This ROM contains the programmable BIOS program.
7. SiI3132 Serial ATAII controller
This motherboard incorporates the high performance SiI3132 IDE
RAID controller, which supports RAID 0, RAID 1 configuration.
8. IEEE 1394a controller
The IEEE 1394a controller provides high-speed and flexible PC
connectivity to a wide range of peripherals and devices compliant
to IEEE 1394a standards. The IEEE 1394a interface allows up to
400Mbps tranfer rates.
9. PCI slots
These two 32-bit PCI 2.3 expansion slots support bus master PCI
cards like SCSI or LAN cards with 133MB/s maximum throughput.
10. LAN controller
The 10/100Mbps LAN delivers a transfer rates up to 10/100Mbps.
11. PCI Express x1 slots
These two PCI Express x1 slots are fully compliant to the PCI
Express Base Specification revision 1.0a.
12. PCI Express x16 slots
This motherboard has two x16 PCI Express slots, which are intended
for external PCI Express graphics cards.
13. Audio CODEC
The audio CODEC is compliant with High Definition Audio Codec and
supports 8-channel audio.
14. Giga LAN controller
The Giga LAN controller delivers a transfer rates up to 10/100/1000
Mbps for the Ethernet connection. Ideal for handling large amounts of
data such as video, audio and voice.
a. Anti-Burn LED indicator
When this LED is lit up, do not remove the memory module from
your DIMM slot or else your memory module will be damaged.
b. PCI LED indicator
The blinking PCI LED indicates the PCI slot activity. These LEDs will
stop blinking when add-in card has been installed. Blinking means no
add card installed or add-in card was not properly installed.
Содержание
- Table of contents 2
- Introduction 6
- Package check list 6
- Bios feature 7
- Chipset 7
- Dual lan 7
- Expansion slots 7
- Feature summary 7
- Ieee 1394a 7
- Internal i 7
- Memory 7
- Rear panel i o 7
- Storage 7
- Auto restart after power loss 8
- Device plug with usb like ease 8
- Double bandwidth sata 8
- Extreme guardian extreme guardian extreme guardian extreme guardian extreme guardian 8
- Extreme power extreme power extreme power extreme power extreme power 8
- Form factor 8
- Increased supercharged 3d graphics performance 8
- Instant and automatic overclocking technology 8
- More bandwidth low latency and betterefficiency 8
- New generation of i o interface 8
- One key boot device selection 8
- Overdrive the hdd performance with ncq 8
- Slash memory access time 8
- Special features 8
- The most effieient algorithm 8
- The most powerful engine 8
- Uncompromising dvd audio quality 8
- Extreme genius extreme genius extreme genius extreme genius extreme genius 9
- Extreme link extreme link extreme link extreme link extreme link 9
- Major components 10
- Headers and connectors 12
- Jumpers 16
- Rear panel 17
- Installing memory module 20
- Installing the cpu 20
- Installing the cpu cooling fan 20
- Apacer hyb25d256800bt 5b 21
- Apacer v58c2256804sat5 21
- Chip selects 21
- Infineon hys64d16301gu 5 b 21
- Infineon hys64d32300gu 5 b 21
- Infineon hys64d32300hu 5 c 21
- Infineon hys64d64320hu 5 c 21
- Micron mt8vddt3264ag 40bc4 21
- Nanya nt128d64sh4b1g 5 21
- Nanya nt128d64sh4b1g 5t 21
- Nanya nt1gd64s8hb0g 5t 21
- Nanya nt256d64s88b1g 5t 21
- Nanya nt512d64s8hb1g 5t 21
- Ramaxel hyb25d256800ce 5c 21
- Samsung m368l3223dtm cc4 21
- Size vendor module name 21
- Table a ddr memory module qvl qualified vendor list the following ddr400 memory modules have been tested and qualified for use with this motherboard 21
- Table b unbuffered dimm support for 939 pin 21
- Connecting ide floppy and sata cable 22
- Installing motherboard in a case 22
- Connecting ide floppy sata device 23
- Installing expansion cards 23
- Connecting the power supply cable 24
- Powering up 24
- Entering the bios setup menu 1 3 updating and recovering the bios 1 26
- Reference 26
- The main menu 3 26
- 1 using award flash to update your bios 27
- Entering the bios setup menu 27
- Updating and recovering the bios 27
- 2 using ecs top hat flash to recover your bios 28
- 1 standard cmos features 29
- The main menu 29
- Access mode auto 30
- Base memory extended memory and total memory 30
- Before attempting to configure a hard disk drive ensure that you have the configuration information supplied by the manufacturer of your hard drive incorrect settings can result in your system not recognizing the installed hard disk 30
- Drive a drive b 1 4m 3 in none 30
- Floppy 3 mode support disabled 30
- Halt on all errors 30
- Ide channel 0 1 master slave ide extended ide drives auto 30
- Ide hdd auto detection 30
- If you are setting up a new hard disk drive that supports lba mode more than one line will appear in the parameter box choose the line that lists lba for an lba drive 30
- To return to the standard cmos features page 30
- Video ega vga 30
- 2 advanced bios features 31
- Apic mode enabled 32
- Ata 66 100 ide cable msg enabled 32
- Boot other device enabled 32
- Boot up floppy seek disabled 32
- Boot up numlock status on 32
- First second third boot device floppy hard disk cdrom 32
- Gate a20 option fast 32
- Hdd s m a r t capability disabled 32
- Mb non os2 32
- Quick power on self test enabled 32
- Security option setup 32
- Swap floppy drive disabled 32
- Typematic rate setting disabled 32
- 3 advanced chipset features 33
- Enables or disables the display of the epa logo during boot 33
- Full screen logo show enabled 33
- Small logo epa show disabled 33
- These items define critical timing parameters of the mainboard you should leave the items on this page at their default values unless you are very familiar with the technical specifications of your system hardware if you change the values incorrectly this may cause fatal errors or instability into your system 33
- To return to the main bios setting page 33
- When enabled this will show a full screen company logo on the boot up screen select disabled when you want to show post messages during boot up 33
- Dram configuration press enter 34
- Timing mode auto 34
- To view the following screen 34
- User config mode auto 34
- Agp aperture size 128mb 35
- Downstream ldt bus width 16 bit 35
- Dual slot configuration disabled 35
- Gfx clock mode sync 35
- Gfx multi function mode disabled 35
- Gfx0 1 link width x16 x8 35
- Ldt bus frequency auto 35
- Ldt configuration enabled 35
- Ldt pci bus control press enter 35
- Pcie gfx core payload size 64 bytes 35
- Pcie gpp core payload size 64 bytes 35
- Pcie reset delay disabled 35
- This item allows users to enable or disable the dual slot confuguration 35
- This item allows users to enable or disable the gfx multi function mode 35
- This item allows users to manually adjust the agp aperture size from 32mb to 2gb 35
- This item allows users to manually adjust the downstream ldt bus width to be 8 bit or 16 bit 35
- This item allows users to manually adjust the ldt bus frequency 35
- This item allows users to manually adjust the pcie gfx core payload size 35
- This item allows users to manually adjust the pcie gpp core payload size 35
- This item allows users to manually adjust the upstream ldt bus width to be 8 bit or 16 bit 35
- This item allows users to manually set the gfx link width 35
- This item allows users to set the gfx clock mode to be sync or async when this item is set to sync the following 3 item is activated 35
- This item enables or disables the ldt configuration 35
- This item enables or disables the pcie reset delay 35
- To return to the advanced chipset features page 35
- To view the following screen 35
- Upstream ldt bus width 16 bit 35
- 4 integrated peripherals 36
- Async gfx clock 200mhz this item allows users to manually adjust the gfx clock from 200mhz to 350mhz 36
- Async gfx clock source 14 18mhz osc this item allows users to set the gfx clock source either to be 14 18mhz osc or 100mhz pcie 36
- Dual mode interleaving disabled 36
- Dynamic cke enabled 36
- Mclk spread spectrum disabled this item allows users to enable or disable the mclk spread spectrum function 36
- System bios cacheable disabled 36
- These options display items that define the operation of peripheral components on the system s input output ports 36
- This feature is only valid when the system bios is shadowed it enables or disables the caching of the system bios rom at f0000h fffffh via the l2 cache this greatly speeds up accesses to the system bios 36
- This item allows users to enable or disable the dual mode interleaving function 36
- This item allows users to enable or disable the dynamic cke function 36
- To return to the main bios setting page 36
- Each ide channel supports a master device and a slave device these four items let you assign the kind of pio programmed input output was used by the ide devices choose auto to let the system auto detect which pio mode is best or select a pio mode from 0 4 37
- Each ide channel supports a master device and a slave device this motherboard supports ultradma technology which provides faster access to ide devices 37
- Enable this field if your ide hard drive supports block mode block mode enables bios to automatically detect the optimal number of block read and writes per sector that the drive can support it also improves the speed of access to ide devices 37
- Ide dma transfer access enabled 37
- Ide hdd block mode enabled 37
- Ide prefetch mode enabled 37
- Ide primary secondary master slave pio auto 37
- If you install a device that supports ultradma change the appropriate item on this list to auto you may have to install the ultradma driver supplied with this motherboard in order to use an ultradma device 37
- Onchip ide channel0 1 enabled 37
- Primary secondary master slave udma auto 37
- South onchip ide device press enter 37
- The onboard ide drive interface supports ide prefetching for faster drive access if you install a primary and secondary add on interface set this field to disable if the interface does not support prefetching 37
- This item allows you to enable the transfer access of the ide dma then burst onto the pci bus and nonburstable transactions do not 37
- To return to the integrated peripherals page 37
- To view the following screen 37
- Use this item to enable or disable the pci ide channels that are integrated on the motherboard 37
- Enable this item if you plan to use a mouse connected through the usb port in a legacy operating system such as dos that does not support plug and play 38
- Enable this item if your system supports usb 2 38
- Onboard 1394 enabled 38
- Onboard azalia audio auto 38
- Onboard lan boot rom disabled 38
- Onboard pci lan enabled 38
- Onboard sata controller both 38
- Onboard sata type ide mode 38
- Sata2 controller enabled 38
- South onchip pci device press enter 38
- This item allows you to enable or disable the sata2 controller function 38
- This item allows you to manually specify the onboard serial ata controller 38
- This item allows you to manually specify the onboard serial ata type 38
- This item enables or disables the usb controller leave this at the default enabled if you want to connect usb devices to your computer 38
- This option allows you to control the onboard azalia audio disable this item if you are going to install a pci audio add on card 38
- This option allows you to control the onboard lan device 38
- This option allows you to enable or disable the onboard 1394 function 38
- To view the following screen 38
- Usb 2 supports enabled 38
- Usb controller enabled 38
- Usb legacy support enabled 38
- Usb mouse support enabled 38
- Use this item to enable and disable the booting from the onboard lan or a network add in card with a remote boot rom installed 38
- Use this item to enable or disable support for legacy usb devices setting to auto allows the system to detect the presence of usb devices at startup if detected theusb controller legacy mode is enabled if no usb device is detected the legacy usb support is disabled 38
- Enables you to set the data transfer protocol for your parallel port there are four options spp standard parallel port epp enhanced parallel port ecp extended capabilities port and ecp epp 39
- Giga lan boot rom disabled 39
- Giga lan controller enabled 39
- Onboard fdc controller enabled 39
- Onboard parallel port 378 irq7 39
- Onboard serial port 1 3f8 irq4 39
- Onboard superio device press enter 39
- Parallel port mode ecp 39
- This field is available if the onboard serial port 2 field is set to any option but disabled uart mode select enables you to select the infrared communication protocol normal default irda or askir 39
- This item allows users to assign the resources for the uart port device 39
- This item allows you to enable or disable the giga lan controller function 39
- This option enables the onboard floppy disk drive controller 39
- This option is used to assign the i o address and interrupt request irq for onboard serial port 1 com1 39
- This option is used to assign the i o address and interrupt request irq for the onboard parallel port 39
- To return to the advanced chipset features page 39
- To view the following screen 39
- Uart mode select irda 39
- Uart port 2f8 irq3 39
- Ur2 duplex mode full this field is available when uart mode is set to either askir or irda this item enables you to determine the infrared function of the onboard infrared chip the options are full and half default full duplex means that you can transmit and send information simultaneously half duplex is the transmission of data in both directions but only one direction at a time 39
- Use this item to enable and disable the booting from the onboard lan or a network add in card with a remote boot rom installed 39
- 5 power management setup 40
- Ecp mode use dma 3 40
- Init display first pci slot 40
- This option lets you control system power management the system has various power saving modes including powering down the hard disk turning off the video suspending to ram and software power down that allows the system to be automatically resumed by certain events 40
- To return to the advanced chipset features page 40
- Use this item to specify whether your graphics adapter is installed in one of the pci slots or is integrated on the motherboard 40
- When the onboard parallel port is set to ecp mode the parallel port can use dma 3 or dma1 40
- Acpi suspend type s3 str 41
- Hdd power down disabled 41
- If you want an incoming call on a modem to automatically resume the system from a power saving mode use this item to specify the interrupt request line irq that is used by the modem you might have to connect the fax modem to the motherboard wake on modem connector for this feature to work 41
- Modem use irq 3 41
- Pwron after pwr fail off 41
- Resume event control press enter 41
- Soft off by pwrbtn instant off 41
- The ide hard drive will spin down if it is not accessed within a specified length of time options are from 1 min to 15 min and disable 41
- This item defines how the video is powered down to save power this item is set to dpms display power management software by default 41
- This item enables your computer to automatically restart or return to its operating status 41
- This option defines if the video is powered down when the system is put into suspend mode 41
- To view the following screen 41
- Under acpi advanced configuration and power management interface you can create a software power down in a software power down the system can be resumed by wake up alarms this item lets you install a software power down that is controlled by the power button on your system if the item is set to instant off then the power button causes a software power down if the item is set to delay 4 sec then you have to hold the power button down for four seconds to cause a software power down 41
- Use this item to define how your system suspends in the default s3 str the suspend mode is a suspend to ram i e the system shuts down with the exception of a refresh current to the system memory 41
- Video off method dpms support 41
- Hot key resume ctrl f1 42
- Resume by pci e enabled 42
- Resume by pci pme enabled 42
- Resume by ps 2 keyboard disabled 42
- Resume by ps 2 mouse disabled 42
- Resume by ring disabled 42
- Resume by usb s3 disabled 42
- Rtc alarm resume disabled 42
- To return to the power management setup screen 42
- 6 pnp pci configurations 43
- Assign irq for usb enabled 43
- If you cannot get a legacy isa industry standard architecture expansion card to work properly you might be able to solve the problem by changing this item to manual and then opening up the irq resources submenu 43
- If you enable this item and restart the system any plug and play configuration data stored in the bios setup is cleared from memory 43
- Names the interrupt request irq line assigned to the usb on your system activity of the selected irq always awakens the system 43
- Pci vga palette snoop disabled 43
- Reset configuration data disabled 43
- Resources controlled by auto auto escd 43
- These options configure how pnp plug and play and pci expansion cards operate in your system both the the isa and pci buses on the motherboard use system irqs interrup requests and dmas direct memory access you must set up the irq and dma assignments correctly through the pnp pci configurations setup utility for the motherboard to work properly selecting pnp pci configurations on the main program screen displays this menu 43
- This item is designed to overcome problems that can be caused by some non standard vga cards this board includes a built in vga system that does not require palette snooping so you must leave this item disabled 43
- To close the irq resources submenu 43
- You should leave this item at the default auto escd under this setting the system dynamically allocates resources to plug and play devices as they are required 43
- 7 pc health status 44
- Cpu vcore system temperature cpu temperature cpu fan speed system fan speed nb fan speed 44
- Enables you to set the maximum temperature the system can reach before powering down 44
- On motherboards that support hardware monitoring this item lets you monitor the parameters for critical voltages temperatures and fan speeds 44
- Power 20 24pin message enabled 44
- Shutdown temperature disabled 44
- System component characteristics 44
- These fields provide you with information about the systems current operating status you cannot make changes to these fields 44
- This item allows users to enable or disable the 20 24pin power cable indication message 44
- This item allows users to manually set the warning temperature of the system 44
- Warning temperature disabled 44
- 3 8 frequency voltage control 45
- Amd k8 cool n quiet control auto 45
- Auto detect pci clk enabled 45
- Cpu clock 200 mhz 45
- Cpu dynamic overclocking disabled 45
- Cpu vcore adjust default 45
- Dimm voltage adjust 2 v 45
- Hammer fid control startup 45
- Hammer vid control startup 45
- If you enable spread spectrum it can significantly reduce the emi electro magnetic interference generated by the system 45
- Spread spectrum 0 45
- This item allows users to adjust the cpu frequency the range will be varied according 45
- This item allows users to adjust the cpu voltage we strongly recommend you leave this item at its default value 45
- This item allows users to enable or disable the cpu dynamic overclocking function 45
- This item allows users to manually adjust the cpu lock 45
- This item allows users to manually adjust the cpu vcore value users are recom mended to keep it at its default value 45
- This item enables you to set the clock speed and system bus for your system the clock speed and system bus are determined by the kind of processor you have installed in your system 45
- This item helps the system to lower the frequency when cpu idles when the frequency decreases the temperature will drop automatically as well 45
- To different cpus we strongly recommend you leave this item at its default value 45
- Use this item to manually adjust the dimm voltage from 45
- When this item is enabled bios will disable the clock signal of free pci slots 45
- 10 load optimized defaults 46
- 9 load performance 46
- 11 set supervisor user password 47
- 12 save exit setup 47
- 13 exit without saving 47
- This chapter delivers contents of the ecs support cd 48
- Running the software cd 50
- Setup button 50
- Setup tab 50
- Software cd information 50
- Application tab 51
- Browse cd button 51
- Exit button 51
- Read me tab 51
- Software utilities introduction 51
- Caractéristi ques du bios 54
- Chipset 54
- Codec audio realtek 8 canaux 54
- Conforme aux high definition audio codec 54
- Contrôleur lan realtek 10 100 mbps 54
- E s du panneau arrière 54
- Français 54
- Ieee 1394a 54
- Lan double 54
- Marvell giga lan 54
- Mémoire 54
- Options d extension 54
- Prend en charge les sdram ddr sans mémoire tampon ddr400 333 266 200 54
- Pris en charge par sb450 54
- Résumé des caractéristiques 54
- Stockage 54
- X clavier ps 2 54
- X prise audio entrée micro sortie de ligne 8 canaux d entrée de ligne 54
- X sockets dimm sdram ddr 2 v 184 broches prenant en charge jusqu à 4 go 54
- E s interne 55
- Facteur de forme 55
- Français 55
- Mm x 244mm 55
- Sortie 55
- Taille atx 55
- Arbeitsspeicher 56
- Award bios mit 4mb oder 8 mb flash rom 56
- Bios merkmale 56
- Chipsatz 56
- Deutsch 56
- Dual lan 56
- Ieee 1394a 56
- Rear panel i o 56
- Speicher 56
- Zusammenfassung der merkmale 56
- Deutsch 57
- Formfaktor 57
- Internes i o internes i o 57
- Caratteristic he bios 58
- Chipset 58
- Deposito 58
- Doppia lan 58
- Ieee 1394a 58
- Indice delle caratteristiche 58
- Italiano 58
- Jack audio mic in porte line in e 58
- Line out 58
- Memoria 58
- Opzioni d espansione 58
- Pannello posteriore i o 58
- Supportata da 58
- Form factor 59
- I o interno 59
- Italiano 59
- Almacenaje 60
- Característi cas de bios 60
- Chipset 60
- Dual lan 60
- Español 60
- I o del panel trasero 60
- Ieee 1394a 60
- Memoria 60
- Opciones de expansión 60
- Resumen de características 60
- Español 61
- Factor de forma 61
- I o interno 61
- Armazenam ento 62
- Característi cas bios 62
- Chipset 62
- Ieee 1394a 62
- Lan duplo 62
- Memória 62
- Opções de expansão 62
- Painel traseiro i o 62
- Português 62
- Sumário de características 62
- Áudio 62
- Coeficiente de forma 63
- I o interno 63
- Português 63
- 4つのultra dma133 100 66 ide デバイス 64
- Acpi revision 1 b 規格に準拠 64
- Biosの諸 機能 64
- High definition audio codec に準拠 64
- Ieee 1394a 64
- Ieee1394a ケーブルポートが2つで 100m bits s 200m bits s および400m bits sの転送率に対応 64
- Marvell giga lan 64
- Mb または 8mb の flash rom のaward bios 64
- Plug play 1 a apm 1 multi boot および dmiをサポート 64
- Realtek 10 100 mbps lan コントローラ 64
- Realtek 8チャネルオーディオcodec 64
- South bridge 64
- Via ieee1394a コントローラ 64
- が1つ 64
- が2つ 64
- が4つ 64
- オーディオ 64
- オーディオジャック マイクロホン入力 ライン入力 お よび8チャネルオライン出力 が1式 64
- チップセット 64
- デュアルlan 64
- プロセッサ 64
- メモリ 64
- 保存装置 64
- 拡張スロット 64
- 日本語 64
- 特徴概要 64
- 背面パネル入 出力 64
- 内部入出力 65
- 寸法 65
- 日本語 65
- Bios 특성 66
- Ieee 1394a 66
- Via ieee1394a 컨트롤러 66
- X ieee1394a 케이블 포트 100m bits s 200m bits s 400m bits s 지원 66
- 뒷 패널 i o 66
- 듀얼 랜 66
- 메모리 66
- 오디오 66
- 저장 66
- 칩셋 66
- 특성 요약 66
- 한 국 어 66
- 확장 옵션 66
- 규격 67
- 내부 i o 67
- 한 국 어 67
- Bios功能 68
- Ieee 1394a 68
- 中央處理器 68
- 功能摘要 68
- 擴充槽 68
- 晶片組 68
- 繁體中文 68
- 背面板 輸出入介面 68
- 記憶體 68
- 雙lan 68
- 音訊 68
- 主機板尺寸 69
- 內部輸出入 介面 69
- 繁體中文 69
- Bios 功能 70
- Ieee 1394a 70
- 内存 70
- 功能摘要 70
- 双 lan 70
- 后面板 i o 70
- 存储 70
- 扩展选项 70
- 简体中文 70
- 芯片组 70
- 音頻 70
- 外形 71
- 简体中文 71
- 集成 i o 71
- Aудиo 72
- Dual lan 72
- Ieee 1394a 72
- Гнезда входа выхода на тыльной панели 72
- Массовая память 72
- Особенности bios а 72
- Память 72
- Русский 72
- Характеристики 72
- Чипсет 72
- Габариты 73
- Русский 73
- Cechy biosu 74
- Chipset 74
- Dual lan 74
- Gniazda we wy na tylnym panelu 74
- Ieee 1394a 74
- Możliwości rozbudowy 74
- Pamięć 74
- Polski 74
- Urządzenia pamięc masowej 74
- Polski 75
- Wewnętrzne gniazda we wy 75
- Wymiary 75
- Disková zařízení 76
- Ieee 1394a 76
- Paměť 76
- Rozšiřující sloty 76
- Souhrn vlastností 76
- Vlastnosti bios 76
- Vstupy výstupy na zadním panelu 76
- Česky 76
- Čipová sada 76
- Interní vstupy výstupy 77
- Velikost 77
- Česky 77
- Caracteristici bios 78
- Codec audio realtek cu 8 canale 78
- Compatibil cu high definition audio codec 78
- Controler lan realtek 10 100 mbps 78
- I o de pe panoul din spate 78
- Ieee 1394a 78
- Lan dual 78
- Memorie 78
- O mufă audio microfon pentru intrare şi 8 canale ieşire audio 78
- Română 78
- Set de chipuri 78
- Sloturi de extindere 78
- Socluri ddr sdram dimm de 2 5 v şi 184 ace cu capacitate maximă de 4 gb 78
- Stocare 78
- Sumarul caracteristicilor 78
- Suport pentru module ddr sdram ddr400 333 266 200 fără zonă tampon 78
- Unitatea centrală cpu 78
- Caracteristici externe 79
- I o internă 79
- Română 79
- Dual lan 80
- Ieee 1394a 80
- Аудио 80
- Български 80
- Възможности за съхраняване на данни 80
- Иди 80
- Канално 80
- Памет 80
- Параметри 80
- Параметри на bios 80
- Портове вход изход на задния панел 80
- Процесор 80
- Слотове за разширяване 80
- Чипсет 80
- Български 81
- Интегриран вход изход контролер 81
- Размери 81
- Bios jellemzők 82
- Bővítési foglalatok 82
- Duál lan 82
- Hátsó panelen levő i o 82
- Ieee 1394a 82
- Jellemzők összefoglalása 82
- Központi egység cpu 82
- Magyar 82
- Memória 82
- Tárolás 82
- Alaki jellemzők 83
- Belső i o 83
- Magyar 83
- Legal notices 84
Похожие устройства
- ECS Elitegroup KN1 Extreme Руководство пользователя
- ECS Elitegroup KN1 SLI Lite Руководство пользователя
- ECS Elitegroup KN2 SLI Руководство пользователя
- ECS Elitegroup D6VAA Руководство пользователя
- ECS Elitegroup MB694A Руководство пользователя
- ECS Elitegroup X79R-AX Руководство пользователя
- ECS Elitegroup X79R-AX Deluxe Руководство пользователя
- ECS Elitegroup A55F-A Руководство пользователя
- ECS Elitegroup A55F-A2 Руководство пользователя
- ECS Elitegroup A55F-M2 (V1.0A) Руководство пользователя
- ECS Elitegroup A55F-M2 (V2.0) Руководство пользователя
- ECS Elitegroup A55F-M3 Руководство пользователя
- ECS Elitegroup A55F-M4 (V1.0) Руководство пользователя
- ECS Elitegroup A55F-M4 (V2.0) Руководство пользователя
- ECS Elitegroup A75F-A Руководство пользователя
- ECS Elitegroup A75F-M Руководство пользователя
- ECS Elitegroup A75F-M2 (V1.0/V1.0A) Руководство пользователя
- ECS Elitegroup A75F-M2 (V2.0) Руководство пользователя
- ECS Elitegroup A890GXM-A2 Руководство пользователя
- ECS Elitegroup A960M-M2 Руководство пользователя