![Nec NC3200S [59/70] 5 specifications](/img/pdf.png)
Nec NC3200S [59/70] 5 specifications
![Nec NC3200S [59/70] 5 specifications](/views2/1375701/page59/bg3b.png)
59
6. Appendix
6-5. Specifications
Model No. NC3200S
Projection method 3 chip DLP Cinema® method (1.25-inch DC2K chip)
Panel resolution 2048 x 1080
Lamp type 4.5/6.0/7.0 kW xenon lamp (Note 1)
Screen sizes 15 m to 30 m (Width) (Depends on setup conditions)
Contrast ratio 2200:1 or above
Lens adjustment function Motorized lens shift (vertical/horizontal), motorized zoom, motorized focus, douser
Signal input ports (Note 2) Slot B Signal input board (NC-80LB01) mounted as standard
SDI (4) BNC (SMPTE 292M, 372M)
RGB DIGITAL (2) DVI-D 24pin (TMDS specification)
Slot A When shipped from factory: Empty (for mounting optional components)
External Control RS-232C D-sub 9 pin x 1
GPIO port D-sub 37 pin x 1
Remote control input port stereo mini jack x 1
3D CTL D-sub 15 pin x 1
USB Type A x 1
Interlock port x 1
Ethernet port G-bit RJ-45 x 1
Anamorphic Lens Turret control port x 1
Power supply
voltage
Projector head AC100 to 240 V, 50/60 Hz single phase
Lamp power supply AC200-230 V, 50/60 Hz Three-phase (Star connection)
AC380-415 V, 50/60 Hz Three-phase (Star connection) Switch type
Input current Projector head 7 A
Lamp power supply 28 A (200 to 230 V), 17 A (380 to 415 V)
Consumption Projector head 0.7 kW
Power Lamp power supply 9.7 kW
Cooling method Cooling fluid system, Cooling air system (includes dust filter)
Noise level Less than 66 dB
Installation Orientation:Desktop/front, Desktop/rear
Net weight Projector head 99 kg (Excluding lens)
Lamp power supply 52 kg
Dimensions Projector head 700 mm (W) x 1124 mm (D) x 503 mm (H) (Does not include protruding
portions Includes foot)
Lamp power supply 594 mm (W) x 397 mm (D) x 452 mm (H)
Environment Operating temperature: 10 to 35 ˚C
Operating humidity: 10 to 85% (non-condensing)
Storage temperature: -10 to 50 ˚C
Storage humidity: 10 to 85%
Regulations
<Safety> <EMC>
USA UL60950-1 FCC Class A
Canada CSA60950-1 ICES-003 Class A
Europe EN60950-1 EN55022 Class A
EN55024
Oceania IEC60950-1 AS/NZS CISPR.22 Class A
Japan J60950 VCCI Class A
Asia IEC60950-1 CISPR. 22
(Note 1) Using any lamp other than NEC’s optional lamps will result in lower brightness compared to NEC optional lamps. If
brightness is important to you, it is recommended that you use NEC’s optional lamps.
NEC will post information on its homepage regarding installable lamps, other than NEC’s optional lamps. Note that
NEC does not guarantee performance and reliability when lamps other than NEC’s optional lamps are installed.
(Note 2) In addition to the input ports described above that are mounted when the device is shipped, Image Media Block and
Multi Media Switcher are available as separate optional products. A wider variety of input interfaces can be supported
by mounting these in slot A.
* Note that these specifications and design can change without prior notice.
Содержание
- Front cover 1
- Nc 32ps01 1
- Nc3200s 1
- User s manual 1
- Important information 2
- Important information 3
- Appendix 51 5
- Installation and connection 17 5
- Maintenance of your projector 43 5
- Projection of images basic operation 20 5
- Table of contents 5
- Table of contents 5 5
- Using menus 31 5
- What s in the box and the names of the projector parts 6 5
- 1 features 6
- What s in the box and the names of the projector parts 6
- Dmd face dust protection structure 7
- Efficient cooling of the heat from the dmd unit by the cooling structure 7
- What s in the box and the names of the projector parts 7
- 2 1 accessories for the projector ns3200s 8
- 2 what s in the box 8
- What s in the box and the names of the projector parts 8
- 2 2 accessories for the lamp power supply nc 32ps01 9
- What s in the box and the names of the projector parts 9
- 3 1 front of the projector 10
- 3 names of the projector parts 10
- What s in the box and the names of the projector parts 10
- Ac power cable for projector 11
- Air inlet for cooling the lamp 11
- Air inlet for cooling the projector electric circuits 11
- Conversion lens stage connector terminal 11
- Conversion lens stay fittings 11
- Dedicated interface cable 11
- Interlock connector inside front of projector 11
- Lens optional 11
- What s in the box and the names of the projector parts 11
- 3 2 rear of the projector 12
- What s in the box and the names of the projector parts 12
- 3 3 lamp power supply nc 32ps01 13
- What s in the box and the names of the projector parts 13
- 3 4 5 6 14
- 3 4 connection terminals 14
- What s in the box and the names of the projector parts 14
- 11 12 14 13 15
- 3 5 control panel 15
- What s in the box and the names of the projector parts 15
- Douser button 16
- Exit button 16
- Imb button 16
- Lamp on off button 16
- Play pause button 16
- Power button 16
- Stop button 16
- Up down left right buttons 16
- What s in the box and the names of the projector parts 16
- 1 steps for setting up and connecting 17
- Installation and connection 17
- 2 connecting the image input terminals 18
- As hdsdi vtr 18
- Dvi d a b input terminal dvi a dvi b inputs digital rgb signals from a pc 18
- Installation and connection 18
- Sdi a sdi b sdi c sdi d hdsdi a b c d input terminal inputs serial digital images from a cinema server or an image device such 18
- The projector has two image input terminals hdsdi input terminal and dvi d input terminal 18
- 3 connecting the various control terminal 19
- Ethernet port lan use this port when controlling the projector in lan connection from a pc 19
- For control your projector comes with such ports as the pc control terminal and the ethernet port rj 45 19
- Installation and connection 19
- Pc control terminal rs 232 use this terminal when controlling the projector in serial connection from a pc 19
- 1 steps of projecting images 20
- Projection of images basic operation 20
- 2 turning your projector on 21
- Projection of images basic operation 21
- Remove the lens cap 21
- Turn on the main power switch on the side of the projector 21
- Turn the main power switch on the lamp power supply to on 21
- Blinking white lamp is off 22
- Button when the inside temperature is abnormally high the protective function prevents power from turning on 22
- Douser button 22
- If key lock is on press the key lock button for one second or longer 22
- Is due to the characteristics of the lamp and is not trouble of your projector 22
- Key lock becomes off the color of the key lock button changes from orange to white and buttons on the control panel become operable see page 28 22
- Lamp on off button 22
- Lit green 22
- Lit green douser is off 22
- Power button 22
- Press the lamp on off button on the control panel for five seconds or longer 22
- Press the power button on the control panel of your projector three seconds or longer 22
- Projection of images basic operation 22
- Projector may be in trouble check the error display on the lcd screen and contact your dealer distributor for instructions note that the image may sometimes flicker until the lamp has stabilized 5 to 10 minutes after power on this 22
- The button which was last selected is lit green 22
- The lamp is turned on and the screen glows light about 15 seconds later the lamp on off button lights green the douser is closed until the screen glows light the douser button blinks white when the douser is open the douser button lights green 22
- Wait some time until the projector inside cools down and then turn on the power when the rear status indicator is blinking in red without the lamp lighting up after power on your 22
- While your projector is on be sure to have the lens cap removed from the lens otherwise the lens cap may get deformed due to a heat buildup in the following instances the power to your projector cannot be turned on even if you press the power 22
- Your projector is turn on and the screen glows light about 30 seconds later the status of the power button douser button and lamp on off button changes as follows 22
- 3 selecting the title of input signal 23
- Projection of images basic operation 23
- 4 1 displaying the test pattern 24
- 4 adjusting the position and the size of projected screen 24
- Adjusting the position and the size of projected screen 24
- Projection of images basic operation 24
- 4 2 adjusting the position of the projected screen lens shift 25
- Projection of images basic operation 25
- 4 3 fine adjustment of the size zoom and focus of the projected screen 26
- Projection of images basic operation 26
- 4 4 adjusting the brightness of the projected screen lamp output 27
- Projection of images basic operation 27
- 5 1 key lock setting 28
- 5 2 turning key lock off 28
- 5 preventing misoperations 28
- Press the key lock button for one second or longer while key lock is on 28
- Press the key lock button on the control panel for one second or longer 28
- Projection of images basic operation 28
- 6 1 turning off the lamp 29
- 6 2 turning on the lamp 29
- 6 turning on off the lamp with the projector turned on 29
- Projection of images basic operation 29
- Turning on off the lamp with the projector turned on 29
- 7 turning your projector off 30
- Press the power button on the projector control panel for three seconds or longer 30
- Projection of images basic operation 30
- Turn off the ac power to the projector head and to the lamp power 30
- Turn the main power switch on the lamp power supply to off 30
- Wait till the projector enters standby state before turning off the main power switch of the projector 30
- 1 1 screen display 31
- 1 basic operation with adjustment menus 31
- Using menus 31
- Function 32
- If a button on the control panel is pressed while the key lock function is on the following is displayed and the button will not 32
- The amount of time remaining for cooling is displayed as shown below when the power to the projector head is turned off 32
- Using menus 32
- When a button is pressed while the key lock function is on 32
- When in standby 32
- When not displaying menus the following screen is normally displayed 32
- When power is turned on 32
- When the power is turned off 32
- When the power is turned on the following is displayed 32
- When the projector is in a standby state the main power switch in on the following is displayed 32
- 1 2 operating menus 33
- Press the down button 33
- Press the left right button to select the submenu version 33
- Press the left right buttons to display information 33
- Press the menu button on the control panel of your projector 33
- Using menus 33
- Press the down button 34
- Press the left right button to select the submenu data 34
- Press the up button several times 34
- Using menus 34
- 1 3 how to enter alphanumeric characters 35
- Using menus 35
- 2 table of adjustment menus 36
- Menus in parentheses are menus for our service personnel normally these menus cannot be used 36
- Using menus 36
- 3 1 title select title memory 37
- 3 2 test pattern 37
- 3 title select 37
- Using menus 37
- 4 1 lamp setup 38
- 4 2 lens control 38
- 4 configuration 38
- Using menus 38
- 5 title setup 39
- 6 1 lamp 39
- 6 information 39
- Using menus 39
- 6 2 preset button 40
- 6 3 usage 40
- 6 4 error code 40
- Using menus 40
- 6 5 version 41
- Mms built in 41
- System 41
- Using menus 41
- 6 6 ip address 42
- 6 7 setup date 42
- 6 8 option status 42
- Displays the link status of the device in slot a 42
- Displays the link status of the device in slot b 42
- Imb media block 42
- Mms multi media switcher 42
- No board no device mounted 42
- Sib signal input board 42
- Using menus 42
- 1 cleaning the cabinet 43
- 2 cleaning the lens 43
- Maintenance of your projector 43
- 3 replacing the air filter 44
- Maintenance of your projector 44
- Warning 44
- 3 1 replacing air filters for the lamp air inlet 45
- Maintenance of your projector 45
- Maintenance of your projector 46
- 3 2 replacing air filters for the projector air inlet on the front 47
- Maintenance of your projector 47
- Maintenance of your projector 48
- 3 3 replacing air filters for the projector air inlets on the side 49
- Maintenance of your projector 49
- Maintenance of your projector 50
- 1 1 problems and where to check 51
- 1 troubleshooting 51
- Appendix 51
- Appendix 52
- 2 1 key lock button 53
- 2 2 power button 53
- 2 3 douser button 53
- 2 4 lamp on off button 53
- 2 indicator display list 53
- Appendix 53
- 2 5 rear status indicator 54
- Appendix 54
- 3 1 overview 55
- 3 2 preparation before use 55
- 3 3 handling of the address for operation via a browser 55
- 3 operation using an http browser 55
- Appendix 55
- 3 4 structure of the http server 56
- Appendix 56
- 4 1 projector head nc3200s 57
- 4 outline drawing 57
- Appendix 57
- 4 2 lamp power supply nc 32ps01 58
- Appendix 58
- 5 specifications 59
- Appendix 59
- Brightness is important to you it is recommended that you use nec s optional lamps nec will post information on its homepage regarding installable lamps other than nec s optional lamps note that nec does not guarantee performance and reliability when lamps other than nec s optional lamps are installed note 2 in addition to the input ports described above that are mounted when the device is shipped image media block and 59
- Multi media switcher are available as separate optional products a wider variety of input interfaces can be supported by mounting these in slot a 59
- Note 1 using any lamp other than nec s optional lamps will result in lower brightness compared to nec optional lamps if 59
- Note that these specifications and design can change without prior notice 59
- 6 1 pc control connector rs 232 d sub 9 pin 60
- 6 pin assignment and functions of terminal 60
- Appendix 60
- 6 2 external control connector gp i o d sub 37 pin 61
- Appendix 61
- Circuits by a photo coupler 8 port input and 8 port output are available 61
- Ext_gpin1 ext_gpin4 you can control the projector externally by combinations of input signals high low 61
- Ext_gpout1 ext_gpout4 functions in the above table are default settings you can change the assigned functions 61
- External control connector gpio general purpose i o ports each pin is electrically separated from the projector internal 61
- It is possible to control the projector with an external device and to control the external device from the projector using an 61
- Please contact your dealer distributor regarding how to use and to operate them 61
- Projector power supply lamp power supply image mute title selection 61
- Appendix 62
- Input connector 62
- The operation command coming from gpi o port will be canceled when the projector is processing other tasks such as lamp cooling and switching title set all other pins than those in use to off the operation command is executed upon continuous input of the on pulse for approximately 200 ms 62
- Using gpio control 62
- Appendix 63
- Timing chart of gpio control 63
- Appendix 64
- Appendix 65
- Default you can change the assigned functions 65
- External devices 65
- Output connector 65
- The following functions are assigned to the pin number 13 32 14 33 15 34 and 16 35 ext_gpout1 ext_gpout4 as the 65
- Using gpio control 65
- You can use gpio control for the projector s health check and error check also you can use the output as the trigger to control 65
- 6 3 3d connector d sub 15 pin 66
- Appendix 66
- This is used to connect a 3d image system to the projector 66
- 6 4 sdi a sdi b sdi c sdi d hd sdi input connector bnc 67
- 6 5 dvi a dvi b dvi digital input connector dvi d 24 pin 67
- Appendix 67
- Edid is available even when the projector is switched off 67
- Generated in the video if you use a dual link cable 67
- The smpte 292 hd sdi transfers hdtv signals with 1 ghz digital serial signals so use a 75 ω coaxial cable having a 67
- Thickness and characteristics higher than 5c fb and use a bnc for the connector 67
- This is a signal input connector smpte 292 hdsdi for cinema 67
- This is a single link dvi input connector that is compliant with hot plug detect hpd use a single link cable noise may be 67
- 7 related products list 68
- Appendix 68
Похожие устройства
- Linkor ВД-170 И У2 Инструкция по эксплуатации
- Linkor ВД-200 И У2 Инструкция по эксплуатации
- Linkor ВД-201 И У2 Инструкция по эксплуатации
- Linkor ВД-230 И У2 Инструкция по эксплуатации
- Linkor ВД-231 И У2 Инструкция по эксплуатации
- Linkor ВД-300 И У2 Инструкция по эксплуатации
- Linkor ПДГ-170М+ММА Инструкция по эксплуатации
- Linkor ПДГ-200И У2 Инструкция по эксплуатации
- Linkor ПДГ-250И У2 Инструкция по эксплуатации
- Linkor ПДГ-200М+ММА Инструкция по эксплуатации
- Linkor ПДГ-250М+ММА Инструкция по эксплуатации
- Linkor ПДГ-253И У2 Инструкция по эксплуатации
- Linkor ПДГ-300И У2 Инструкция по эксплуатации
- Linkor ПДГ-350И У2 Инструкция по эксплуатации
- Linkor ПДГ-500И У2 Инструкция по эксплуатации
- Linkor ПДГ-630И У2 Инструкция по эксплуатации
- WWQ CN 25/40-180 Инструкция по эксплуатации
- WWQ CN 25/60-180 Инструкция по эксплуатации
- WWQ CN 25/80-180 Инструкция по эксплуатации
- WWQ CN 25/120-180 Инструкция по эксплуатации
Скачать
Случайные обсуждения