Zelmer ZSB1200X (32Z012) [34/36] After operation
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Zelmer ZSB1200X (32Z012) [34/36] After operation

Zelmer ZSB1200X (32Z012) [34/36] After operation
38 32Z012-002_v04
1
Pour approximately 1 liter of water to the blender jug (9)
and start-up the appliance for approximately 30 seconds and
hold the CLEAN/PULSE button.
2
Then empty the blender jug (9), turn it upside-down
and dry.
3
If necessary, clean the jug (9), lid (8), feeder opening
stopper (7) and blades (14) in warm water with wash-up
liquid.
●
Then rinse it under clean running water and dry.
●
If you left the jug for longer time without cleaning and
some particles glued to the jug inner, use nylon brush.
●
We do not recommend cleaning the jug (9), blades (14),
lid (8) and feeder opening stopper (7) in dish washer.
Aggressive cleaning agents applied in such device can
inuence negative the surface conditions.
4
Clean the outsider of the motor housing (10) with damp,
gentle cloth.
Do not immerse the motor housing (10) in
water or other liquid.
●
Do not clean the outside of the housing (10) with
aggressive detergents such as emulsion milk or pastes,
etc. They can remove information graphic symbols.
●
Do not clean the transparent jug (9) with harsh sponges
or clothes.
●
After washing dry thoroughly all the parts of the
appliance.
Cutting unit disassembling
●
Unplug from the mains supply outlet.
●
Empty the jug (9).
●
Remove the lid (8) from the blender jug (9). Turn the
blender jug (9) „upside down” and place on the at and
rm surface.
●
Turn the blocking ring counter clockwise. Remove
carefully with a gasket.
The cutting blades are sharp. Handle them
carefully.
Cutting unit assembling
●
Turn the blades upside down in order to assemble them
and insert at rst the gasket at the jug opening ange (9)
and blades inside the jug (9).
●
Insert blocking ring and turn it clockwise until it runs.
Make sure that the blocking ring is screwed to the jug (9).
It inuences the tightness of the connection.
●
After assembling, turn the jug (9) upside down and place
it on the motor housing (10) so, that the protrusions in
bottom part of the jug (9) are tted with the protrusions
top part of the motor housing (10).
The handle of the blender jug (9) shall be placed on the right
side of the appliance.
10
Press ON/OFF switch to turn off the appliance.
Operating with speed I or speed II, the
appliance is switched off automatically after
2 minutes.
11
CLEAN/PULSE function
●
Pressing CLEAN/PULSE (6) button shall cause short
operation with maximum speed.
●
Do not operate longer than 3 minutes, otherwise it can
get overheated.
●
If you need to add some new ingredients during blender
operation, turn and lift feeder opening stopper (7), feed
the ingredients into the opening, then replace the stopper
again (7) and turn it left or right until it runs.
●
Make sure, that the ingredients you add, shall not
increase the capacity inside the jug exceeding 1500 ml
marking on the jug (9).
12
ICE function
●
Check if the stand blender is clean, before you use it for
crushing ice. Otherwise wash it thoroughly with clean
water. Any residues of washing agent can inuence the
taste of crushed ice and shall cause that the drink we
add the ice to, shall loose its taste.
●
In case you want to crush ice, use 6 to 10 ice cubes
(max. 2 cm) in given time, and then add 15 ml (1 spoon)
fresh cold water.
●
Assemble the lid (8) including overlay (7) on the appli-
ance and press ICE switch.
ICE feature operates for 30 seconds, then the
appliance switches off automatically.
Do not try to crush the ice without adding some
water into the jug.
Press the lid (8) with one hand during ICE
feature is on.
After operation
To switch off the stand blender press and hold ON/OFF
switch for 3 seconds, until the blue highlight around the
control panel (11) is off.
●
Hold the motor unit (10) with one hand, catch the jug
handle with the other hand and remove it from the motor
unit (10) turning it counter-clockwise.
●
Remove the lid (8) from the jug (9).
●
Unplug the appliance from the mains supply outlet when
it is not in use.
Cleaning and maintenance
Clean after operation as soon as possible,
to prevent the pulp accumulation inside the
jug (9).
C

Содержание

Похожие устройства

Скачать