Bosch PSB 750 RCE 0.603.128.503 [18/100] Operation

Bosch PSB 750 RCE 0.603.128.503 [18/100] Operation
18 | English
2 609 005 110 | (30.5.11) Bosch Power Tools
Press on the holder of the filter element 17 and pull it out. Re-
place the filter element 17 including the holder. When placing
on the holder again, make sure that the rubber gasket 18 is in-
serted.
Reattach the dust collector 12 again and lock it by pressing
against the smooth surface of the release button 16.
Removing the Extraction Device (see figure E)
For disassembly of the extraction device 11, press release
button 20 and pull off the extraction device 11 toward the
front.
Stowing the Extraction Device (see figure F)
For stowing the extraction device 11 in the case, remove the
extraction device 11, slide it together and attach clamp 21.
Attach the locking latch 22 or empty the dust collector 12 be-
fore placing down the extraction device.
Auxiliary Handle
f Operate your machine only with the auxiliary handle 9.
The auxiliary handle 9 can be set to any position for a secure
and low-fatigue working posture.
Turn the wing bolt for adjustment of the auxiliary handle 10 in
anticlockwise direction and set the auxiliary handle 9 to the
required position. Then tighten the wing bolt 10 again in
clockwise direction.
Adjusting the Drilling Depth (see figure G)
The required drilling depth X can be set with the depth stop 1.
Press the button for the depth stop adjustment 3 and insert
the depth stop into the auxiliary handle 9.
The knurled surface of the depth stop 1 must face downward.
Pull out the depth stop until the distance between the tip of
the drill bit and the tip of the depth stop correspond with the
desired drilling depth X.
Changing the Tool
Keyless Chuck (PSB 750 RCE/PSB 750 RCA)
(see figure H)
The drill spindle is locked when the On/Off switch 8 is not
pressed. This makes quick, convenient and easy changing of
the tool in the drill chuck possible.
Open the keyless chuck 2 by turning in rotation direction n,
until the tool can be inserted. Insert the tool.
Firmly tighten the collar of the keyless chuck 2 by hand in ro-
tation direction o until the locking action (“click”) is no longer
heard. This automatically locks the chuck.
The locking is released again to remove the tool when the col-
lar is turned in the opposite direction.
Keyless Chuck (PSB 650 RE/PSB 6500 RE/PSB 650 RA)
(see figure I)
f Press the spindle lock button 25 only when the ma-
chine is at a standstill.
The drill spindle is locked by pressing the spindle lock button
25. This makes quick and easy changing of the tool in the drill
chuck possible.
Open the keyless chuck 2 by turning in rotation direction n,
until the tool can be inserted. Insert the tool.
Firmly tighten the collar of the keyless chuck 2 by hand in ro-
tation direction o until the locking action (“click”) is no longer
heard. This automatically locks the chuck.
The locking is released again to remove the tool when the col-
lar is turned in the opposite direction.
Screwdriver Tools
When working with screwdriver bits 24, a universal bit holder
23 should always be used. Use only screwdriver bits that fit
the screw head.
For driving screws, always position the “Drilling/Impact Drill-
ing” selector switch 4 to the “Drilling” symbol.
Replacing the Drill Chuck (PSB 750 RCE/
PSB 750 RCA)
Removing the Drill Chuck (see figure J)
Clamp the short end of an Allen key 26 into the keyless chuck 2.
Place the machine on a stable surface, e. g. a workbench.
Hold the machine firmly and loosen the keyless chuck 2 by
turning the Allen key 26 in rotation direction n. Loosen a
tight seated keyless chuck by giving the long end of the Allen
key 26 a light blow. Remove the Allen key from the keyless
chuck and completely unscrew the keyless chuck.
Mounting the Drill Chuck (see figure K)
The keyless chuck is mounted in reverse order.
The drill chuck must be tightened with a tightening
torque of approx. 2535 Nm.
Replacing the Drill Chuck (PSB 650 RE/
PSB 6500 RE/PSB 650 RA)
Removing the Drill Chuck (see figure L)
Clamp the short end of an Allen key 26 into the keyless chuck
2.
Place the machine on a firm surface, e. g. a workbench. Hold
the machine firmly, press the spindle lock button 25 and loos-
en the keyless chuck 2 by turning the Allen key 26 in rotation
direction n. Loosen a tight keyless chuck by giving the long
end of the Allen key 26 a light blow. Remove the Allen key
from the keyless chuck and completely unscrew the keyless
chuck.
Mounting the Drill Chuck (see figure M)
The keyless chuck is mounted in reverse order.
The drill chuck must be tightened with a tightening
torque of approx. 2535 Nm.
Operation
Starting Operation
f Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the
nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
OBJ_DOKU-27001-001.fm Page 18 Monday, May 30, 2011 8:03 AM

Содержание

181 English Press on the holder of the filter element 17 and pull it out Re place the fil ter el ement 17 including the holder When placi ng Firmly tighten the collar of the keyless chuck 2 by hand in ro tation di recti on unti I the locking action dick is no longer on the holder again makesure that the rubber gasket 18 is in heard This automatically locks the chuck serted The locking is released again to remove the tool when the col Reattach the dust collector 12 again and lock it by pressing against the smooth surface of the release button 16 lar is turned in the opposite direction Removing the Extraction Device seefigure E For disassembly of the extraction device 11 press release When working with screwdriver bits 24 auniversal bit holder 23 should always be used Use only screwdriver bits that fit button 20 and pull off the extraction device 11 toward the the screw head front For driving screws always position the Drilling lmpact Drill Stowing the Extraction Device see figureF For stowing the extraction device 11 in the case remove the extraction device 11 si ide it together and attach damp 21 Screwdriver Tools i ng sei ector switch 4 to the D ri I li ng symbol Replacing the Drill Chuck PSB 750 RCE PSB 750 RCA Attach the locking latch 22 or empty the dust collector 12 be fore placi ng d own the extraction d evice Auxiliary Handle Removingthe Drill Chuck see figure J Clamp the s hort end of an Allen key 26 into the keyless chuck 2 Operate your machine only with the auxiliary handle 9 Place the machine on a stable surface e g a workbench Hold the machine firmly and loosen the keyless chuck 2 by The auxiliary handle 9 can be set to any position for a secure turning the Allen key 26 in rotation direction O Loosen a andlow fatigueworkingposture tight seated keyless chuck by givi ng the long end of the Al len Turn the wing bol t for adj us tmen t of the auxil iary handle 10 i n key 26 a light blow Remove the Allen key from the keyless chuck and completely unscrew the keyless chuck anticlockwise direction and set the auxiliary handle 9 to the required position Then tighten the wing bolt lOagainin clockwise direction Mounting the Drill Chuck see figure K The keyless chuck is mounted in reverse order AdjustingtheDrilling Depth see figureG The drill chuck must be tightened witha tightening The required dri Hi ng depth X can be set wi th the depth stop 1 torqueofapprox 25 35Nm Press the button for the depth stop adjustment 3 and insert the depth stop into the auxiliary handle 9 The knurled surface of thedepth stop 1 must face downward Replacing the Drill Chuck PSB 650 RE PSB 6500 RE PSB 650 RA Pull out the depth stop until the distance between the tip of Removingthe Drill Chuck see figure L the drill bit and the tip of the depth stop correspond with the Clamp the short end of an Allen key 26 into the keyless chuck desired drilling depth X 2 Cha ngingthe Tool Place the machine on a firm surface e g a workbench Hold KeylessChuck PSB 750RCE PSB 750 RCA see figure H en the keyless chuck 2 by turning the Allen key 26 in rotation direction O Loosen a tight keyless chuck by giving the long The drill spindle is locked when the On Off switch Sis not end of the Allen key 26 a light blow Remove the Allen key pressed This makes quick convenient and easy changing of the tool in the drill chuck possible from the keyless chuck and completely unscrew the keyless Open the keyless chuck 2 by turning in rotation direction O until the tool can be inserted Insert the tool Firmly tighten the collar of the keyless chuck 2 by hand in ro tation direction until the locking action dick isno longer heard This automatically locks the chuck themachinefirmly pressthespindlelockbutton25and loos chuck Mounting the Drill Chuck see figure M The keyless chuck is mounted in reverse order The drill chuck must be tightened witha tightening torqueofapprox 25 35Nm The locking is released again to remove the tool when the col lar is turned in the opposite direction Keyless Chuck PSB 650 RE PSB 6500 RE PSB 650 RA see figure I Press the spindle lock button 25 only when the machineisata standstill The drill spindle is locked by pressing the spindle lock button 25 This makes quick and easy changing of the tool in the drill Operation Starting Operation Observe correct mains voltage The voltage of the pow er source must agree with the voltage specified on the nameplate of the machine Power tools marked with 230 V can also be operated with 220 V chuck possible Open the keyless chuck 2 by turning in rotation direction O until the tool can be inserted Insert the tool 26О9ОО511ОЦЗО 5 11 Bosch Power Tools

Скачать