Stiga TORNADO 2098 H [50/168] Standards of use

Stiga TORNADO 2098 H [50/168] Standards of use
5. STANDARDS OF USE
5.1
BEFORE EVERY USE
Before every use, perform the following checking 
procedures in order to assure a regular operation.
5.1.1
Check oil level
See  the  specific  chapter  (8.1)  for  the  oil  to  be 
used. 
a) Place engine level.
b) Clean around oil fill.
c) Unscrew the cap (1), clean the end of the dip-
stick (2) and replace it, resting the cap on the 
filler, as seen in the illustration, without tighten-
ing it.
d) Remove the cap with the dipstick and check 
the oil level that must be between the «MIN» 
and «MAX» marks.
e) If oil is required, add oil of the same kind up to 
the «MAX» mark, being careful not to spill any 
outside the oil fill.
f) Fully tighten the fillercap (1) and wipe off any 
spilled oil.
5.1.2
Check air cleaner
The  efficiency  of the  air  filter is fundamental  for 
the  engine  to  work  properly.  Do  not  start  the 
engine if the filtering element is missing or broken. 
a) Clean around the filter cover (1).
b) Remove the cover (1) by unscrewing the two 
knobs (2 - TRE0701 - TRE0801), or by press-
ing the tabs (2a - TRE0702).
c) Check the condition of the filtering element (3). 
It must be intact, clean and in perfect working 
order;  if  not,  either carry  out  maintenance  or 
replace it (see 6.5).
d) Put the cover (1) back.
5.1.3
Refuelling
IMPORTANT
Do not drip fuel onto the
plastic parts of the motor or the machine to pre-
vent damaging them and remove all traces of
spilt fuel immediately. The warranty does not
cover damage to plastic parts caused by fuel.
The fuel characteristics are  given in the specific 
paragraph (see 4.2 and 8.1).
Refuelling  must  be  made  when  the  engine  is 
cold,  following  the  instructions  contained  in  the 
machine’s Instructions Manual.
5.1.4
Spark plug cap
Firmly connect the cable cap (1) to the spark plug 
(2),  making  sure that  there  are  no traces  of  dirt 
inside the cap and on the spark plug terminal.
5.2
STARTING THE ENGINE (cold)
The engine must be started in the way described 
in the machine’s Instruction Manual, always mak-
ing  sure  that  any  device  (if  present)  that  could 
cause the  machine  to  advance  or  the engine to 
stop is disengaged.
a) Move the throttle to «CHOKE».
b) Turn  the  starter  key  as  described  in  the 
machine’s instruction manual.
After a few seconds, slowly move the throttle from 
«CHOKE» to either «FAST» or «SLOW».
5.3
STARTING THE ENGINE (hot starting)
•)  Follow the whole cold-starting procedure with 
throttle control in «FAST» position.
5.4
USE OF THE ENGINE IN OPERATION
Maximum  revs  must  be  used  to  optimise  the 
engine’s  yield  and  performance,  by  setting  the 
throttle trigger to «FAST».
WARNING!
Keep your hands away
from the silencer and surrounding areas
that can become extremely hot. With the
engine running, do not get loose-fitting
clothing (ties, scarves, etc.) or hair closer
to the top part of the engine.
4
EN

Содержание

Похожие устройства

Скачать
Случайные обсуждения

Ответы 0

Зарядка экамулятора
2 года назад

Ответы 1

Какое масло заливать?
3 года назад