![Icom IC-Q7A [16/43] Memory call channels](/img/pdf.png)
Icom IC-Q7A [16/43] Memory call channels
![Icom IC-Q7A [16/43] Memory call channels](/views2/1074437/page16/bg10.png)
12
5
MEMORY/CALL CHANNELS
■ General
The transceiver has 200 memory channels in 2 banks and 2
call channels for storage of often-used frequencies.
D Memory/call channel contents
The following information can be programmed into memory
or call channels:
•Operating frequency (p. 7)
•Receive mode (p.11)
•Tuning step (p.7)
•Duplex direction (DUP or –DUP) with an offset frequency
(pgs. 22, 24)
•Subaudible tone encoder or tone squelch ON/OFF (pgs.
23, 26)
•Subaudible tone and tone squelch frequencies (pgs. 23,
26)
•Scan skip setting (p. 18)
■
Programming during selection
q Select VFO mode with [V/M].
w Set the desired frequency:
➥Select the desired band with [BAND].
➥Set the frequency using [DIAL].
➥Set other data (e.g. offset frequency, duplex direction,
subaudible tone frequency, etc.), if required.
e Push [FUNC] + [V/M] momentarily to indicate memory
channels.
•Do not hold [FUNC] + [V/M] for more than 0.5 sec., otherwise the
memory channel will overwrite the selected memory channel.
r Rotate [DIAL] to select the desired channel.
•Call channels (C1, C2) and VFO (VF), as well as regular memory
channels, can be programmed in this way.
•Rotate [DIAL] while pushing [FUNC] to select a memory channel
in 10 channel steps.
t Push [FUNC] + [V/M] for 2 sec. to program.
FM DUPTSQL
MR
FM DUPTSQLFM
MR
momentarily
blank channel
for 2 sec.
+
V/M
FUNC
+
V/M
FUNC
[EXAMPLE]: Programming ch 40 during selection.
Содержание
- Dual band fm transceiver 1
- Instruction manual 1
- Iq7a iq7e 1
- Cautions 2
- Do not 2
- Explicit definitions 2
- Foreword 2
- R warning neve 2
- Read all instruction 2
- Save this instruction manual 2
- Caution 3
- Supplied accessories 3
- Table of contents 4
- Accessory attachment 5
- Caution 5
- D antenna 5
- D battery installation 5
- D belt clip 5
- D handstrap 5
- I panel description 6
- Panel description 6
- Panel description 7
- I function display 8
- Panel description 8
- Panel description 9
- Frequency and channel setting 10
- I operating band selection 10
- Vfo and memory call channels 10
- D using set mode 11
- D using the band switch 11
- Frequency and channel setting 11
- I setting a frequency 11
- I setting a tuning step 11
- Frequency and channel setting 12
- I lock function 12
- I rit function 12
- I selecting a memory channel 12
- Basic operation 13
- Caution 13
- I receiving and transmitting 13
- Basic operation 14
- I monitor function 14
- I setting squelch level 14
- I setting volume level 14
- Basic operation 15
- D setting the backlighting setting 15
- D setting the receive mode 15
- I display backlighting 15
- I receive mode selection 15
- I general 16
- Memory call channels 16
- Programming during selection 16
- I programming after selection 17
- I transferring memory contents to another memory 17
- Memory call channels 17
- D programming a call channel 18
- D selecting a call channel 18
- I call channel 18
- I memory clear 18
- Memory call channels 18
- I scan types 19
- Scan operation 19
- D memory bank selection 20
- I full band programmed scan 20
- I memory bank scan 20
- Scan operation 20
- I selecting scan edges 21
- Scan operation 21
- D setting the scan pause time 22
- D setting the scan resume time 22
- I scan resume condition 22
- I skip channel setting 22
- Scan operation 22
- D frequency skip function on off 23
- D programming a skip frequency 23
- I frequency skip function 23
- Scan operation 23
- I priority watch types 24
- Priority watch 24
- D memory call channel watch and memory scan watch 25
- D vfo scan watch 25
- I priority watch operation 25
- Priority watch 25
- D setting duplex and duplex direction 26
- I general 26
- Repeater operation 26
- Available subaudible tone frequencies unit hz 27
- D setting the subaudible tone frequency 27
- D turning the subaudible tone encoder on off 27
- E while pushing func rotate dial to select tone r push v m to exit set mode 27
- Each operating band and each memory channel have inde pendent settings 27
- I subaudible repeater tones 27
- Q push v m for 2 sec to enter set mode w rotate dial until t tsql appears 27
- Q select vfo mode or desired memory channel to be pro grammed w push v m for 2 sec to enter set mode e rotate dial until r tone repeater tone appears 27
- R while pushing func rotate dial to select the desired subaudible tone 27
- Repeater operation 27
- Some repeaters require subaudible tones to be accessed subaudible tones are superimposed over your normal signal and must be set in advance 27
- T push v m to exit set mode 27
- Europe and italy versions only 28
- I 1750 hz tone 28
- I offset frequency 28
- Repeater operation 28
- D frequency range and offset direction 29
- I auto repeater function 29
- Repeater operation 29
- U s a version only 29
- D operation 30
- D setting subaudible tones for tone squelch operation ctcss tones 30
- I tone squelch operation 30
- Subaudible tone operation 30
- D calling a waiting station using pocket beep 31
- D waiting for a call from a specific station 31
- I pocket beep operation 31
- I tone scan 31
- Subaudible tone operation 31
- D expanded set mode on off 32
- D set mode items 32
- I set mode 32
- Other functions 32
- D setting dial select step 33
- I beep tones 33
- I dial select step 33
- I power saver 33
- Other functions 33
- I auto power off function 34
- I monitor switch function 34
- Other functions 34
- I dial speed acceleration 35
- I lock function effect 35
- Other functions 35
- Caution 36
- I all reset 36
- I channel indication mode 36
- I partial reset 36
- Other functions 36
- If your transceiver seems to be malfunctioning please check the following points before sending it to a service center 37
- Problem possible cause solution ref 37
- Troubleshooting 37
- Call channel mode 38
- Displays for set and expanded set modes show the default settings except the expanded set mode setting 38
- Memory mode 38
- Operation flow chart 38
- Rotate dial while pushing func to change the set mode condition 38
- Vfo mode 38
- Operation flow chart 39
- Set mode expanded set mode 39
- D general 40
- D transmitter 40
- Specifications 40
- D receiver 41
- Specifications 41
- Options 42
- 9 16 kamihigashi hirano ku osaka 547 0002 japan 43
- Count on us 43
Похожие устройства
- Panasonic DMC-GF5KEE-K Инструкция по эксплуатации
- Icom IC-T2H Инструкция по эксплуатации
- Panasonic DMC-GF5KEE-R Red Инструкция по эксплуатации
- Icom IC-T7H Инструкция по эксплуатации
- Panasonic DMC-GF5XEE-K Black Инструкция по эксплуатации
- Icom IC-T90A Инструкция по эксплуатации
- Panasonic DMC-GF5XEE-R Red Инструкция по эксплуатации
- Icom IC-T22A Инструкция по эксплуатации
- Panasonic DMC-GF5XEE-W White Инструкция по эксплуатации
- Icom IC-T81A Инструкция по эксплуатации
- Samsung ES90 Black Инструкция по эксплуатации
- Icom IC-V8 Инструкция по эксплуатации
- Samsung ES90 Red Инструкция по эксплуатации
- Icom IC-V85 Инструкция по эксплуатации
- Samsung ES90 Silver Инструкция по эксплуатации
- Icom IC-W32A Инструкция по эксплуатации
- Ardo 56 GG40 VX Инструкция по эксплуатации
- Samsung ST76 Red Инструкция по эксплуатации
- Icom ID-800H Инструкция по эксплуатации
- Ardo 56 GG40 X Инструкция по эксплуатации