![Icom IC-Q7A [25/43] I priority watch operation](/img/pdf.png)
Icom IC-Q7A [25/43] I priority watch operation
![Icom IC-Q7A [25/43] I priority watch operation](/views2/1074437/page25/bg19.png)
21
7
PRIORITY WATCH
■Priority watch operation
DMemory/call channel watch and memory
scan watch
q Select VFO mode; then, set an operating frequency.
w Set the watching channel(s).
For memory channel watch:
Select the desired memory channel.
For memory scan watch:
Select memory mode; then, push [FUNC] + [Y] or [Z] mo-
mentarily to start memory scan.
For call channel watch:
Select the call channel by pushing [CALL].
e Push [V/M] for 2 sec. to enter set mode.
r Rotate [DIAL] until “PRIO” appears.
•“PRIO” disappears after 1 sec. and “OFF” and “PR” appear.
t While pushing [FUNC], rotate [DIAL] to select priority
watch ON or priority watch ON with alert.
y Push [V/M] to exit set mode and start the watch.
•The transceiver checks the memory
or call channel frequency every 5 sec.
•The watch resumes according to the
selected scan resume condition. (p.
18)
u Push [V/M] while the display
shows the VFO frequency to stop
the watch.
DVFO scan watch
q Select the desired memory channel to be watched.
w Push [V/M] to select VFO mode.
e Push [FUNC] + [Y] or [Z] momentarily to start full scan,
band scan or programmed scan. (p. 16)
r Push [V/M] for 2 sec. to enter set mode.
t Rotate [DIAL] until “PRIO” appears.
•“PRIO” disappears after 1 sec. and
“OFF” and “PR” appear.
y While pushing [FUNC], rotate
[DIAL] to select priority watch ON
or priority watch ON with alert.
u Push [V/M] to exit set mode and
start the watch.
•The transceiver checks the memory
channel frequency every 5 sec.
•The watch resumes according to the
selected scan resume condition. (p.
18)
i Push [V/M] while the display
shows the VFO frequency to stop
the watch.
Priority watch is ON.
Priority watch set mode
Priority watch with
alert is ON.
PRIO
FM
MR
While pausing on the
memory or call channel
“PRIO” flashes.
Содержание
- Dual band fm transceiver 1
- Instruction manual 1
- Iq7a iq7e 1
- Cautions 2
- Do not 2
- Explicit definitions 2
- Foreword 2
- R warning neve 2
- Read all instruction 2
- Save this instruction manual 2
- Caution 3
- Supplied accessories 3
- Table of contents 4
- Accessory attachment 5
- Caution 5
- D antenna 5
- D battery installation 5
- D belt clip 5
- D handstrap 5
- I panel description 6
- Panel description 6
- Panel description 7
- I function display 8
- Panel description 8
- Panel description 9
- Frequency and channel setting 10
- I operating band selection 10
- Vfo and memory call channels 10
- D using set mode 11
- D using the band switch 11
- Frequency and channel setting 11
- I setting a frequency 11
- I setting a tuning step 11
- Frequency and channel setting 12
- I lock function 12
- I rit function 12
- I selecting a memory channel 12
- Basic operation 13
- Caution 13
- I receiving and transmitting 13
- Basic operation 14
- I monitor function 14
- I setting squelch level 14
- I setting volume level 14
- Basic operation 15
- D setting the backlighting setting 15
- D setting the receive mode 15
- I display backlighting 15
- I receive mode selection 15
- I general 16
- Memory call channels 16
- Programming during selection 16
- I programming after selection 17
- I transferring memory contents to another memory 17
- Memory call channels 17
- D programming a call channel 18
- D selecting a call channel 18
- I call channel 18
- I memory clear 18
- Memory call channels 18
- I scan types 19
- Scan operation 19
- D memory bank selection 20
- I full band programmed scan 20
- I memory bank scan 20
- Scan operation 20
- I selecting scan edges 21
- Scan operation 21
- D setting the scan pause time 22
- D setting the scan resume time 22
- I scan resume condition 22
- I skip channel setting 22
- Scan operation 22
- D frequency skip function on off 23
- D programming a skip frequency 23
- I frequency skip function 23
- Scan operation 23
- I priority watch types 24
- Priority watch 24
- D memory call channel watch and memory scan watch 25
- D vfo scan watch 25
- I priority watch operation 25
- Priority watch 25
- D setting duplex and duplex direction 26
- I general 26
- Repeater operation 26
- Available subaudible tone frequencies unit hz 27
- D setting the subaudible tone frequency 27
- D turning the subaudible tone encoder on off 27
- E while pushing func rotate dial to select tone r push v m to exit set mode 27
- Each operating band and each memory channel have inde pendent settings 27
- I subaudible repeater tones 27
- Q push v m for 2 sec to enter set mode w rotate dial until t tsql appears 27
- Q select vfo mode or desired memory channel to be pro grammed w push v m for 2 sec to enter set mode e rotate dial until r tone repeater tone appears 27
- R while pushing func rotate dial to select the desired subaudible tone 27
- Repeater operation 27
- Some repeaters require subaudible tones to be accessed subaudible tones are superimposed over your normal signal and must be set in advance 27
- T push v m to exit set mode 27
- Europe and italy versions only 28
- I 1750 hz tone 28
- I offset frequency 28
- Repeater operation 28
- D frequency range and offset direction 29
- I auto repeater function 29
- Repeater operation 29
- U s a version only 29
- D operation 30
- D setting subaudible tones for tone squelch operation ctcss tones 30
- I tone squelch operation 30
- Subaudible tone operation 30
- D calling a waiting station using pocket beep 31
- D waiting for a call from a specific station 31
- I pocket beep operation 31
- I tone scan 31
- Subaudible tone operation 31
- D expanded set mode on off 32
- D set mode items 32
- I set mode 32
- Other functions 32
- D setting dial select step 33
- I beep tones 33
- I dial select step 33
- I power saver 33
- Other functions 33
- I auto power off function 34
- I monitor switch function 34
- Other functions 34
- I dial speed acceleration 35
- I lock function effect 35
- Other functions 35
- Caution 36
- I all reset 36
- I channel indication mode 36
- I partial reset 36
- Other functions 36
- If your transceiver seems to be malfunctioning please check the following points before sending it to a service center 37
- Problem possible cause solution ref 37
- Troubleshooting 37
- Call channel mode 38
- Displays for set and expanded set modes show the default settings except the expanded set mode setting 38
- Memory mode 38
- Operation flow chart 38
- Rotate dial while pushing func to change the set mode condition 38
- Vfo mode 38
- Operation flow chart 39
- Set mode expanded set mode 39
- D general 40
- D transmitter 40
- Specifications 40
- D receiver 41
- Specifications 41
- Options 42
- 9 16 kamihigashi hirano ku osaka 547 0002 japan 43
- Count on us 43
Похожие устройства
- Panasonic DMC-GF5KEE-K Инструкция по эксплуатации
- Icom IC-T2H Инструкция по эксплуатации
- Panasonic DMC-GF5KEE-R Red Инструкция по эксплуатации
- Icom IC-T7H Инструкция по эксплуатации
- Panasonic DMC-GF5XEE-K Black Инструкция по эксплуатации
- Icom IC-T90A Инструкция по эксплуатации
- Panasonic DMC-GF5XEE-R Red Инструкция по эксплуатации
- Icom IC-T22A Инструкция по эксплуатации
- Panasonic DMC-GF5XEE-W White Инструкция по эксплуатации
- Icom IC-T81A Инструкция по эксплуатации
- Samsung ES90 Black Инструкция по эксплуатации
- Icom IC-V8 Инструкция по эксплуатации
- Samsung ES90 Red Инструкция по эксплуатации
- Icom IC-V85 Инструкция по эксплуатации
- Samsung ES90 Silver Инструкция по эксплуатации
- Icom IC-W32A Инструкция по эксплуатации
- Ardo 56 GG40 VX Инструкция по эксплуатации
- Samsung ST76 Red Инструкция по эксплуатации
- Icom ID-800H Инструкция по эксплуатации
- Ardo 56 GG40 X Инструкция по эксплуатации