Home
Главная
Bomann
Парогенератор
DR 921 CB
Инструкция по эксплуатации Страница: 31

Bomann DR 921 CB [31/54] Initial operation

18 Floor brush nozzle

19 Window wiper

20 Steam pistol

21 Steam switch on the connecting head

22 Lock ON or OFF/LOCK

Unpacking the Device

• Remove the main device and accessories from the box.

• Also remove any packaging materials that may be present.

• Check the scope of delivery.

Initial Operation

Filling up the Heating Boiler before Use!

Before the tank cap is opened it must be ensured that the device

is not under any pressure. Please proceed as follows:

1. Remove the plug from the socket.

2. Turn the lock (22) on the steam pistol (20) to ON (Fig. B1).

3. Press the steam switch (21) on the steam pistol (Fig. B2).

Point the steam nozzle at a surface which is allowed to

become wet.

NOTE:

After prolonged periods of non-use it is normal for a small

quantity of condensation to come out of the steam pistol at

rst.

WARNING:

• If the device is still warm after an interruption to its

use there is a danger of injury!

• Please open the safety lock (6) only when no more

steam comes out of the nozzle.

4. Turn the lock in an anticlockwise direction.

NOTE:

For your protection the safety lock has a release device. If

the pressure in the kettle is still too high, this release device

prevents it from being opened.

5. Shake any residual water out of the kettle (7). Fill fresh-

water from the measuring beaker (15) into the kettle. Take

care of water splashes that might come out of the boiler. In

order to avoid water spray, please use the funnel supplied

(Fig. E). The water should be lled in slowly.

CAUTION:

Do not overll! Max. water capacity: 1.5 litres.

• Do not use condensation from a tumble dryer (chemical

residues)! This is not distilled water!

6. Retighten the safety lock (6) in a clockwise direction.

Attachment of the Individual Accessories

It is possible to attach the individual nozzles directly to the

steam pistol (20) of the hose (1):

• Plug the adapter (14) onto the steam gun until it clicks into

place.

• To detach the adapter again, press the button on the steam

gun.

• Keep the button pressed and pull out the adapter.

Or extend the nozzle attachments with one or two extension

tubes (8):

• Please insert the sections of the 2-part extension tube one

inside the other until it locks into place (Fig. G). Then attach

it to the steam pistol (20).

• Attach the oor brush (18) to the extension tubes: press the

jointed adapter (17) on to the oor brush and turn it tightly

through 180°.

• If you would like to use the non-woven cloth, attach it to the

oor brush with the help of the clips (Fig. H).

• In order to release the extension tube, please press the

button on the steam pistol.

NOTE:

Various attachments can only be used in conjunction with the

adapter (14). Check that everything is properly connected!

Nozzle Adapter Use

Floor brush

(18)

Jointed

adapter (17)

•

for large oor surfaces (Fig. J)

• with non-woven cloth: for

sensitive surfaces (Fig. K)

Round

brushes (11)

with adapter

(14)

• for joints, ttings, grill grid

etc or

• for difcult-to-access areas

(Fig. I and L)

High-pres-

sure nozzle

(12)

with adapter

(14)

• for concentrated, high

steam pressure (Fig. M)

Window

wiper (19)

with adapter

(14)

• for windows or shower parti-

tions

WARNING: There is a danger of injury!

Never attach or remove the accessories if the steam switch

(21) is pressed in! Wait until the device has cooled down.

Electrical Connection

•

Before inserting the plug into the socket. Make sure that the

mains voltage to be used matches that of the device.

You can nd this information on the nameplate.

• Connect the device to a duly installed 230 V/50 Hz protective

contact socket.

Bomann DR 921 CB [31/54] Initial operation

Содержание

Похожие устройства