Home
Главная
Skil
Шаберы
1490 NA
Инструкция по эксплуатации Страница: 6

Skil 1490 NA Инструкция по эксплуатации онлайн [6/112] 92590

b) Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or

the battery pack from the power tool before making

any adjustments, changing accessories, or storing

power tools. Such preventive safety measures reduce

the risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained

users.

e) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc., in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations dierent

from those intended could result in a hazardous situation.

5) SERVICE

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

SAFETY INSTRUCTIONS FOR MULTI-FUNCTION

TOOLS

GENERAL

• This tool should not be used by people under the age of

16 years

• Use completely unrolled and safe extension cords with a

capacity of 16 Amps (U.K. 13 Amps)

• Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool (tools with

a rating of 230V or 240V can also be connected to a

220V supply)

• Avoid damage that can be caused by screws, nails and

other elements in your workpiece; remove them before

you start working

• Secure the workpiece (a workpiece clamped with

clamping devices or in a vice is held more securely than

by hand)

• Do not work materials containing asbestos (asbestos

is considered carcinogenic)

• Alwaysdisconnectplugfrompowersourcebefore

making any adjustment or changing any accessory

• When working, always hold the tool rmly with both

hands and take a secure stance

• Always keep the cord away from moving parts of the tool;

direct the cord to the rear, away from the tool

• Use protective gloves when changing accessories

(contact with the accessory can lead to injuries)

• In case of electrical or mechanical malfunction,

immediately switch o the tool and disconnect the plug

• If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

• Never use the tool when cord is damaged; have it

replaced by a qualied person

• When you put away the tool, switch o the motor and

ensure that all moving parts have come to a complete

standstill

WHEN SAWING/CUTTING

• Hold power tool by insulated gripping surfaces,

when performing an operation where the cutting

accessory may contact hidden wiring or its own

cord (a cutting accessory contacting a “live” wire may

make exposed metal parts of the power tool “live” and

could give the operator an electric shock)

• Keep hands away from cutting area; never reach

underneath the material for any reason while cutting

• Use suitable detectors to find hidden utility lines or

call the local utility company for assistance (contact

with electric lines can lead to re or electrical shock;

damaging a gas line can result in an explosion;

penetrating a water pipe will cause property damage or

an electrical shock)

• Do not use a saw blade which is cracked, deformed or

dull

WHEN SANDING

• Dust from material such as paint containing lead, some

wood species, minerals and metal may be harmful

(contact with or inhalation of the dust may cause allergic

reactions and/or respiratory diseases to the operator or

bystanders); wear a dust mask and work with a dust

extraction device when connectable

• Certain kinds of dust are classied as carcinogenic (such

as oak and beech dust) especially in conjunction with

additives for wood conditioning; wear a dust mask and

work with a dust extraction device when

connectable

• Follow the dust-related national requirements for the

materials you want to work with

• Use the tool only for dry sanding (penetration of water

into the tool increases the risk of an electric shock)

• Do not touch the moving sanding sheet

• Do not continue to use worn, torn or heavily clogged

sanding sheets

• When sanding metal, sparks are generated; do not use

vacuum cleaner and keep other persons and combustible

material from work area

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

• If for any reason the old plug is cut o the cord of this tool,

it must be disposed of safely and not left unattended

USE

• Changing accessories 4

! disconnect the plug

- remove/mount the required accessory as illustrated

- ensure that the openings of the accessory engange

into the tabs of the tool head (any snap-in position

possible)

- mount the accessory with the depressed centre

pointing downwards

- loosen/fasten screw A with hex key B

Содержание

Похожие устройства

b Do not use the power tool If the switch does not turn It on and off Any power tool that cannot be controlled with the switch is dangerous and must be repaired c Disconnect the plug from the power source and or the battery pack from the power tool before making any adjustments changing accessories or storing power tools Such preventive safety measures reduce the risk of starting the power tool accidentally d Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these Instructions to operate the power tool Power tools are dangerous in the hands of untrained users e Maintain power tools Check for misalignment or binding of moving parts breakage of parts and any other condition that may affect the power tool s operation If damaged have the power tool repaired before use Many accidents are caused by poorly maintained power tools f Keep cutting tools sharp and clean Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control g Use the power tool accessories and tool bits etc In accordance with these Instructions taking Into account the working conditions and the work to be performed Use of the power tool for operations different from those intended could result in a hazardous situation 5 SERVICE a Have your power tool serviced by a qualified repair person using only identical replacement parts This will ensure that the safety of the power tool is maintained If the cord is damaged or cut through while working do not touch the cord but immediately disconnect the plug Never use the tool when cord is damaged have it replaced by a qualified person When you put away the tool switch off the motor and ensure that all moving parts have come to a complete standstill WHEN SAWING CUTTING Hold power tool by insulated gripping surfaces when performing an operation where the cutting accessory may contact hidden wiring or Its own cord a cutting accessory contacting a live wire may make exposed metal parts of the power tool live and could give the operator an electric shock Keep hands away from cutting area never reach underneath the material for any reason while cutting Use suitable detectors to find hidden utility lines or call the local utility company for assistance contact with electric lines can lead to fire or electrical shock damaging a gas line can result in an explosion penetrating a water pipe will cause property damage or an electrical shock Do not use a saw bl ade which I s cracked deformed or dull WHEN SANDING Dust from material such as paint containing lead some wood species minerals and metal may be harmful contact with or inhal ation of the dust may cause all ergi c reactions and or respiratory diseases to the operator or bystanders wear a dust mask and work with a dust extraction device when connectable Certain kinds of dust are classified as carcinogenic such as oak and beech dust especially in conjunction with additives for wood conditioning wear a dust mask and work with a dust extraction device when connectable Follow the dust related national requirements for the materials you want to work with Use the tool only for dry sanding penetration of water into the tool increases the risk of an electric shock Do not touch the moving sanding sheet Do not continue to use worn torn or heavily clogged sanding sheets When sanding metal sparks are generated do not use vacuum cleaner and keep other persons and combustible material from work area WHEN CONNECTING NEW 3 PIN PLUG U K ONLY Do not connect the blue neutral or brown live wire in the cord of this tool to the earth terminal of the plug If for any reason the old plug is cut off the cord of this tool it must be disposed of safely and not left unattended SAFETY INSTRUCTIONS FOR MULTI FUNCTION TOOLS GENERAL This tool should not be used by people under the age of 16 years Use completely unrolled and safe extension cords with a capacity of 16 Amps U K 13 Amps Always check that the supply voltage is the same as the voltage indicated on the nameplate of the tool tools with a rating of 230V or 240V can also be connected to a 220V supply Avoid damage that can be caused by screws nails and other elements in your workpiece remove them before you start working Secure the workpiece a workpiece clamped with clamping devi ces or i n a vice i s hel d more securely than by hand Do not work materials containing asbestos asbestos is considered carcinogenic Always disconnect plug from power source before making any adjustment or changing any accessory When working always hold the tool firmly with both hands and take a secure stance Always keep the cord away from moving parts of the tool direct the cord to the rear away from the tool Use protective gloves when changing accessories contact with the accessory can lead to injuries In case of electrical or mechanical malfunction immediately switch off the tool and disconnect the plug USE Changing accessories I disconnect the plug remove mount the required accessory as illustrated ensure that the openings of the accessory engange into the tabs of the tool head any snap in position possible mount the accessory with the depressed centre pointing downwards loosen fasten screw A with hex key B 6

Скачать