Skil 0780 RA Инструкция по эксплуатации онлайн [11/220] 92846
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Skil 0780 RA Инструкция по эксплуатации онлайн [11/220] 92846

Skil 0780 RA Инструкция по эксплуатации онлайн [11/220] 92846
11
proper precautions are taken; do not let go of the chain
saw)
- donotoverreachanddonotcutaboveshoulder
height (this helps prevent unintended tip contact and
enables better control of the chain saw in unexpected
situations)
- onlyusereplacementbarsandchainsspecified
bythemanufacturer (incorrect replacement bars
and chains may cause chain breakage and/or
kickback)
- followthemanufacturer’ssharpeningand
maintenanceinstructionsforthesawchain
(decreasing the depth gauge height can lead to
increased kickback)
PERSONALSAFETY
• It is recommended that the rst time user should have
practical instruction in the use of the chainsaw and the
protective equipment from an experienced operator and
that the initial practice should be cutting logs on a saw
horse or cradle
• Donottouchrotatingchain
• Donotoperatechainsawnearotherpeople,
childrenoranimals
• Donotoperatechainsawafterdrinkingalcoholor
undertheinfluenceofintoxicatingdrugsor
medication
• This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction
concerning use of the tool by a person responsible for
their safety
• Ensure that children do not play with the tool
ElECTRICAl SAFETY
• Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool
• Connect the tool via a fault current (FI) circuit breaker
with a triggering current of 30 mA maximum
• Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
• Only use an extension cord which is intended for outdoor
use and equipped with a watertight plug and coupling-
socket
• Only use extension cords with a maximum length of 20
metres (1,5 mm²) or 50 metres (2,5 mm²)
• Always switch o tool and disconnect plug from power
source if the power supply cord or the extension cord is
cut, damaged or entangled (donottouchthecord
beforedisconnectingtheplug)
• Protect the (extension) cord from heat, oil and sharp
edges
• Never use the cord for carrying, pulling or unplugging the
tool
• Inspect the cord periodically and have it replaced by a
qualied person, if damaged
• Inspect the extension cord periodically and replace it, if
damaged (inadequateextensioncordscanbe
dangerous)
• Do not use the tool if the switch does not turn it on and
o; always have a damaged switch repaired by a qualied
person
EXPLANATIONOFSYMBOLSONTOOL
3Readtheinstructionmanualbeforeuse
4Alwaysswitchofftoolanddisconnectplugfrom
powersourceifthepowersupplycordorthe
extensioncordiscut,damagedorentangled(donot
touchthecordbeforedisconnectingtheplug)
5 Do not expose tool to rain
6 Wear protective glasses and hearing protection
7 Double insulation (no earth wire required)
8 Do not dispose of the tool together with household waste
material
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
• If for any reason the old plug is cut o the cord of this tool,
it must be disposed of safely and not left unattended
USE
• Assembly 9
! donotconnectthechainsawtomainsbeforeitis
completelyassembled
! alwaysusegloveswhenhandlingthechain
- place the chain saw on any suitable at surface
- remove cover plate A by turning locking knob B
counter-clockwise
- slide chain C in the slot around chain bar D
! ensurechainisincorrectrunningdirectionby
comparingwithchainsymbolE
- t the chain onto drive sprocket F and guide chain bar
D, so that fastening bolt G and the two guide ns H t
into the keyway of chain bar D, and that chain
tensioning peg J ts into the respective hole of chain
bar D
- if necessary, turn tensioning knob K to bring tensioning
peg J in alignment with the hole in chain bar D
- check if all parts are seated properly and hold chain
and chain bar in a level position
- turn tensioning knob K until all the slack is taken up in
the chain
- mount cover plate A as illustrated
- tighten locking knob B on fastening bolt G by turning it
clockwise
• Tensioning chain 0
- place the chain saw on any suitable at surface
- check if the chain links are correctly located in the slot
around chain bar D
1) loosen locking knob B until it is just holding chain bar
in position (donotremove)
2) lift the chain bar somewhat and hold it in that position
3) turn chain tensioning knob K upwards until the lowest
chain links come up and JUST touch the bottom of
chain bar D
4) tighten locking knob B by turning it clockwise
5) release chain bar
6) the correct chain tension is reached when the chain
can be raised approx. 4 mm from the chain bar in the
centre
! alwayscheckthechaintensionbeforeuse,after
thefirstcutsandregularlyduringuse(approx.
every10minutes)
- upon initial operation, new chains can lengthen
considerably

Содержание

Похожие устройства

EXPLANATION OF SYMBOLS ON TOOL Read the Instruction manual before use Always switch off tool and disconnect plug from power source If the power supply cord or the extension cord Is cut damaged or entangled do not touch the cord before disconnecting the plug Do not expose tool to rain Wear protective glasses and hearing protection Double insulation no earth wire required Do not dispose of the tool together with household waste material WHEN CONNECTING NEW 3 PIN PLUG U K ONLY Do not connect the blue neutral or brown live wire in the cord of this tool to the earth terminal of the plug If for any reason the old plug is cut off the cord of this tool it must be disposed of safely and not left unattended proper precautions are taken do not let go of the chain saw do not over reach and do not cut above shoulder height this helps prevent unintended tip contact and enables better control of the chain saw in unexpected situations only use replacement bars and chains specified by the manufacturer incorrect replacement bars and chains may cause chain breakage and or kickback follow the manufacturer s sharpening and maintenance Instructions for the saw chain decreasing the depth gauge height can lead to increased kickback PERSONAL SAFETY It is recommended that the first time user should have practical instruction in the use of the chainsaw and the protective equipment from an experienced operator and that the initial practice should be cutting logs on a saw horse or cradle Do not touch rotating chain Do not operate chain saw near other people children or animals Do not operate chain saw after drinking alcohol or under the Influence of Intoxicating drugs or medication This tool is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the tool by a person responsible for their safety Ensure that children do not play with the tool ELECTRICAL SAFETY Always check that the supply voltage is the same as the voltage indicated on the nameplate of the tool Connect the tool via a fault current Fl circuit breaker with a triggering current of 30 mA maximum Use completely unrolled and safe extension cords with a capacity of 16 Amps U K 13 Amps Only use an extension cord which is intended for outdoor use and equipped with a watertight plug and coupling socket Only use extension cords with a maximum length of 20 metres 1 5 m m2 or 50 metres 2 5 mm2 Always switch off tool and disconnect plug from power source if the power supply cord or the extension cord is cut damaged or entangled do not touch the cord before disconnecting the plug Protect the extension cord from heat oil and sharp edges Never use the cord for carrying pulling or unplugging the tool Inspect the cord periodically and have it replaced by a qualified person if damaged Inspect the extension cord periodically and replace it if damaged Inadequate extension cords can be dangerous Do not use the tool if the switch does not turn it on and off always have a damaged switch repaired by a qualified person USE Assembly I do not connect the chain saw to mains before It Is completely assembled I always use gloves when handling the chain place the chain saw on any suitable flat surface remove cover plate A by turning locking knob B counter clockwise slide chain C in the slot around chain bar D I ensure chain Is In correct running direction by comparing with chain symbol E fit the chain onto drive sprocket F and guide chain bar D so that fastening bolt G and the two guide fins H fit into the keyway of chain bar D and that chain tensioning peg J fits into the respective hole of chain bar D if necessary turn tensioning knob K to bring tensioning peg J in alignment with the hole in chain bar D check if all parts are seated properly and hold chain and chain bar in a level position turn tensioning knob K until all the slack is taken up in the chain mount cover plate A as illustrated tighten locking knob B on fastening boltG by turning it clockwise Tensioning chain place the chain saw on any suitable flat surface check if the chain links are correctly located in the slot around chain bar D 1 loosen locking knob B until it is just holding chain bar in position do not remove 2 lift the chain bar somewhat and hold it in that position 3 turn chain tensioning knob K upwards until the lowest chain links come up and JUST touch the bottom of chain bar D 4 tighten locking knob Bby turning it clockwise 5 release chain bar 6 the correct chain tension is reached when the chain can be raised approx 4 mm from the chain bar in the centre I always check the chain tension before use after the first cuts and regularly during use approx every 10 minutes upon initial operation new chains can lengthen considerably 11

Скачать