Tc Electronic G-FORCE [47/63] The blocks
![Tc Electronic G-FORCE [47/63] The blocks](/views2/1011798/page47/bg2f.png)
45
THE BLOCKS
QUAD TAP DELAY
Quad Tap Delay
Tap 1-4
Sets the delay time of the four taps. Maximum delay
time per tap is 1480 ms.
Tempo 1-4
The Tempo parameter sets the relationship to the
global Tempo e.g. if you set it to 1/4T you will get
quarter note triplets of the tapped tempo. 1/4 equals
the BPM (tapped Tempo).
If you select “Ignored” the current parameter will use
the Preset value and will not be affected by the Global
Tempo.
Feedback 1-4
Adjusts the amount of Feedback from each of the four
taps.
NOTE: The sum of the four feedbacks are limited to
100%.
Levels 1-4
Sets the level of each of the four taps.
Pan position 1-4
Controls the panning of the four Delay taps.
Lowcut 1-4
Cuts off frequencies lower than the selected. The slope
of the filter is 12dB/octave.
Highcut 1-4
Cuts off frequencies higher than the selected
frequency. So if you feel that there is too much treble in
your signal, you remove this by adjusting the highcut
filter down. The slope of the filter is 12dB/octave.
Mix
Mix between direct sound and effect.
In Level
Controls the input level of the block.
Out Level
Controls the output level of the Delay block
Mute mode
See Mute mode in the introduction of this chapter.
The Drive
The Drive block
The Drive is a post distortion. It can be used for effects
purposes like overdriving a Delay, a Flanger or a
Phaser etc. or simply to crank the overall sound a bit.
Drive
The Drive parameter is simulating the In-gain of a
distortion device. The extra In-gain is automatically
compensated on the Output level, to avoid any clipping
internally.
Brightness
Brightness is used to reduce the amount of high
frequency content in the distorted signal. The
Brightness control is flat when set to 100%.
Body
Body is used to reduce the amount of low frequency
content in the distorted signal. At heavy distortion the
Drive will emphasize a lot of low frequencies, which
can be somewhat annoying. These problems can be
reduced by the Body parameter. A number of preamps
and pedals on the market combine a lowcut filter with
their In-gain to compensate for the exact same
problem.
Smasher
The Smasher is used to change the character of the
distortion by emphasizing even order harmonics.
Setting this parameter to a high value, will smash your
signal. Try to experiment with the character of your
distortion.
Содержание
- User s manual 1
- Important safety instructions 3
- Important safety instructions 4
- 6 7 8 10 11 12 16 17 18 29 21 25 29 31 32 33 48 49 50 51 52 54 5
- Table of contents 5
- About this manual 7
- Congratulations 7
- Welcome 7
- From a users point of view 8
- Editing 9
- General control 9
- Input output 9
- Quick reference 9
- Quick store 9
- Recall 9
- Setting up an expression pedal 9
- Setting up your midi board 9
- The front panel 10
- The rear panel 12
- The signal flow 13
- How to 14
- How to build a user preset 14
- How to 15
- How to connect the modifiers 15
- How to 16
- How to set up an expression pedal 16
- How to 17
- How to recall a single block from an existing preset 17
- How to set up my midi board 17
- G force setup 18
- Setups 18
- General 19
- Recall 19
- Recalling a preset 19
- Recalling a single effect 19
- The recall display 19
- Delete 20
- Store a new user preset 20
- The letterbox 20
- Using a memory card 20
- Effects 21
- Editing an effect 22
- Effects 22
- I o setup 23
- I o setup 24
- Ext controllers 25
- I o setup 25
- How the modifiers are connected 26
- I o setup 26
- Setting up an expression pedal 26
- Matrix 27
- Modifier 27
- Envelope follower 28
- Modifier 28
- Modifiers 28
- Adsr 1 2 29
- Lfo 1 2 29
- Modifier 29
- Config 30
- Modifier utility 30
- Utility 30
- Utility 31
- Billboard 32
- Utility 32
- The tuner display 34
- Algorithms 35
- The blocks 35
- Compressor 36
- Filters 36
- The blocks 36
- Parametric equalizer 37
- Resonance 37
- The blocks 37
- Formant filters 38
- The blocks 38
- Wah wah 38
- Pan trem block 39
- Phaser 39
- The blocks 39
- Tremolo 39
- Panner 40
- The blocks 40
- The blocks 41
- The pitch block 41
- Fixed 1 2 voice pitch 42
- The blocks 42
- Voice 2 octave 42
- Detune 43
- Stereo delay 43
- The blocks 43
- The blocks 44
- Dual two tap delay 45
- The blocks 45
- One tap delay 46
- The blocks 46
- Quad tap delay 47
- The blocks 47
- The drive 47
- Classic chorus 48
- The blocks 48
- The chorus flanger block 48
- Advanced chorus 49
- Flanger classic 49
- The blocks 49
- Advanced flanger 50
- The blocks 50
- The blocks 51
- The reverb block 51
- The blocks 52
- Output 53
- Simple reverb 53
- The blocks 53
- How to enter the reset page 54
- The reset page 54
- Technical specifications 55
- Troubleshooting 56
- Midi implementation chart 57
- Self test 58
- Preset list 59
- Preset list 60
- Preset list 61
- Preset list 62
- Preset list 63
Похожие устройства
- Hertz HP 2 Инструкция по эксплуатации
- Casio EX-Z800 Black Инструкция по эксплуатации
- Maxwell MW-1003 Инструкция по эксплуатации
- Champion LM5126BS Инструкция по эксплуатации
- Toshiba SD-63HK Инструкция по эксплуатации
- Hertz HP 1 D Инструкция по эксплуатации
- Gree Bee Plasma GWH24ND-K3NNB3B Инструкция по эксплуатации
- Tc Electronic G-MAJOR Инструкция по эксплуатации
- Casio EX-ZS5 Black Инструкция по эксплуатации
- Mega 4120 XAS Инструкция по эксплуатации
- Maxwell MW-1012 Инструкция по эксплуатации
- Toshiba SD-57HTKR Инструкция по эксплуатации
- Hertz HP 1 KD Инструкция по эксплуатации
- Tc Electronic G-SHARP Инструкция по эксплуатации
- Casio EX-ZS10 Pink Инструкция по эксплуатации
- Champion 3053-C2 Инструкция по эксплуатации
- Toshiba SD-47HKSR Инструкция по эксплуатации
- Pandora программирование брелков Инструкция по эксплуатации
- Tc Electronic G-SYSTEM Инструкция по эксплуатации
- Hertz Hertz HE 2 Инструкция по эксплуатации
Скачать
Случайные обсуждения