Zelmer SB1001 [47/50] Caution
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Zelmer SB1001 [47/50] Caution

Zelmer SB1001 [47/50] Caution
51SB1001-001_v01
Dear Customer!
Congratulations on your choice of our appliance, and
welcome among the users of Zelmer products.
Please read this instruction manual carefully. Pay special
attention to important safety instructions. Keep this instruction
manual for future reference.
Safety operation instructions
Make sure that the following guidelines have been
understood.
Before using the device, read the whole content of the
manual.
Caution!
Not observance can result in damage to
possessions
Connect the appliance to 230 V mains supply.
●
Do not unplug by pulling on cord.
●
The supplying cord shall not be hanged over the edge
●
of the table or board, nor touch any hot surface.
Do not ll the jug in with boiling liquids.
●
Keep the stand blender and supplying cord away from
●
hot surfaces and burners.
If it is possible, store the stand blender away from
●
direct sun radiation and glow-like light.
Never store the blender with the lid on the jug. Moisten
●
the lid sealing ring with water, and place the lid on the
blender jug before use.
Do not ll the jug over 1500 ml mark – in such case,
●
the content of the jug can lift the lid when the motor
starts up.
Do not overow the jug. In case the liquid gets under
●
the motor housing, it can be vacuumed into the motor,
causing its damage.
The stand blender should not be running continuously
●
for more than 60 seconds. Switch the appliance off
after 60 seconds, and wait another 60 seconds before
you run it again, allowing the motor to cool down. Do
not repeat the cycle more than 10 times.
Do not operate when the jug is empty, as it can get
●
overheated.
The temperature of mixed ingredients should not
●
exceed 60°C.
Suggestion
Information on the product and suggestions
for its use
The stand blender is intended for domestic usage only.
●
In case it is used for gastronomic business purposes,
warranty terms and conditions change.
During rst start-up the appliances can emit some
●
odours. It is a normal phenomenon, which should be
over after a time.
Danger! / Warning!
Health hazard
Always place the appliance on at, plain surface.
●
Always unplug the appliance when it is not in use and
●
before cleaning.
Do not operate the appliance if the cord, the housing or
●
the handle is visibly damaged. In such a case, return
the appliance to a service center.
If the non-detachable part of the cord is damaged, it should
●
be replaced by the producer or at a proper service point or
by a qualied person in order to avoid any hazards.
The appliance should be repaired by trained staff only.
●
Improper repair can result in serious hazard for a user.
In case of defects we recommend you to contact
qualied service desk.
Do not immerse motor housing in water or any other
●
liquid; do not use it in bathroom and outdoors.
Turn the knob to the “OFF” position before removing
●
the lid from the jug or the jug from the motor unit. Wait
until blades have come to a complete standstill.
Switch the appliance off, and unplug it from the mains
●
before assembling or disassembling accessories or
touching parts that move during operation.
Do not use stand blender without feeder opening stopper.
●
Do not put your hands inside the jug, even if it is
●
removed for cleaning, as the cutting blades are still
dangerous – very sharp.
Do not put any objects (spoon, etc.) into the jug, when
●
the blender is connected to power supply.
Do not wash the cutting blades directly with hand.
●
Use the soft brush for washing metal parts, especially
●
the sharp blades.
This appliance is not intended for use by persons
●
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by
a person responsible for their safety.
Children should be supervised to ensure that they do
●
not play with the appliance.
Safety recommendations
The stand blender has thermal protection, which turns off
the device at the moment of overheating. In this case, it is
necessary to disconnect the device from the power source.
Remove the plug from the contact, then wait at least 20
minutes, allowing the motor to cool down. After this time, you
can re-attach the stand blender.
EN

Содержание

Похожие устройства

Скачать