Home
Главная
Gigabyte
Сервер
G241-G40 (rev. 100)
Инструкция Страница: 56

Gigabyte G241-G40 (rev. 100) [56/117] 2 2 redfish host interface settings

- 56 - BIOS Setup

5-2-2 Redsh Host Interface Settings

Parameter

Description

Redsh Host Interface Settings

BMC Redsh Version

Displays the Redsh version supported by BMC.

BIOS Redsh Version

Displays the Redsh version supported by BIOS.

Authenticaion mode

Selects Authentication mode.

Options available: Basic Authentication/Session Authentication.

Default setting is Enable.

Redsh BMC Settings

IP address

Enter IP address.

IP Mask address

Enter IP Mask address.

IP Port

Enter IP Port.

Содержание

G241 g40 1
User manual 1
Copyright 2
Disclaimer 2
Documentation classifications 2
For more information 2
In order to assist in the use of this product gigabyte provides the following types of documentation 2
Information in this manual is protected by copyright laws and is the property of gigabyte changes to the specifications and features in this manual may be made by gigabyte without prior notice no part of this manual may be reproduced copied translated transmitted or published in any form or by any means without gigabyte s prior written permission 2
Conventions 3
The following conventions are used in this user s guide 3
Server warnings and cautions 4
Electrostatic discharge esd 5
Chapter 1 hardware installation 1 7
Chapter 2 system appearance 7 7
Chapter 3 system hardware installation 3 7
Chapter 4 motherboard components 5 7
Chapter 5 bios setup 9 7
Table of contents 7
108 5 7 save exit menu 109 8
2 advanced menu 54 8
3 chipset setup menu 74 8
4 server management menu 94 8
5 security menu 101 8
6 boot menu 104 8
8 bios post codes 11 9
9 bios post beep code ami standard 117 9
This page intentionally left blank 10
1 installation precautions 11
Chapter 1 hardware installation 11
2 product specifications 12
3 system block diagram 16
1 front view 17
Chapter 2 system appearance 17
Hdd 0 hdd 1 hdd 2 hdd 3 17
2 3 4 6 5 7 18
2 rear view 18
Psu1 psu2 18
3 front panel led and buttons 19
No name color status description 19
4 rear system lan leds 20
5 power supply unit psu led 21
Psu led 21
1 depends on hba utility spec 22
2 blink cycle depends on hdd s activity signal 22
3 if hdd is pulled out during rebuilding the disk status of this hdd is regarded as faulty 22
6 hard disk drive leds 22
Green on off 22
Led 2 hdd present no hdd 22
System appearance 22 22
Chapter 3 system hardware installation 23
1 removing chassis cover 24
2 removing and installing the fan duct 25
Cpu fan duct 25
Gpu fan duct 25
3 removing the heat sink 26
Cpu1 heat sink 26
4 installing the cpu 27
5 1 six channel memory configuration 29
5 installing the memory 29
5 2 installing a memory 30
5 3 dimm population table 30
Before installing a memory module make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage to the memory module be sure to install ddr4 dimms on this motherboard follow these instructions to install the memory 30
Insert the dimm memory module vertically into the dimm slot and push it down 2 close the plastic clip at both edges of the dimm slots to lock the dimm module 3 reverse the installation steps when you want to remove the dimm module 30
System hardware installation 30 30
6 installing the pci expansion card 31
7 installing the gpu card 32
8 installing the hard disk drive 33
9 installing the m device and heat sink 34
10 replacing the fan assembly 35
11 replacing the power supply 36
12 cable routing 37
Front panel leds and buttons 37
Front panel usb 3 port 37
Onboard sata 38
System main power 38
Hdd backplane board fan power 39
Hdd backplane board power 39
Gpu riser card power 40
Pmbus signal 40
Gpu power 300w 41
Gpu signal 0 41
Gpu signal 1 42
Gpu signal 2 42
Gpu signal 3 43
This page intentionally left blank 44
1 motherboard components 45
11 12 13 14 15 17 18 45
24 23 22 45
6 7 8 9 45
Chapter 4 motherboard components 45
2 jumper settings 47
47 motherboard components 47
This page intentionally left blank 48
Bios setup program function keys 49
Chapter 5 bios setup 49
Advanced 50
Chipset 50
Save exit 50
Security 50
Server management 50
1 the main menu 51
2 advanced menu 54
2 1 trusted computing 55
2 2 redfish host interface settings 56
2 3 serial port console redirection 57
2 4 sio configuration 61
2 5 pci subsystem settings 62
2 6 usb configuration 63
2 7 post report configuration 64
2 8 nvme configuration 65
2 9 chipset configuration 66
2 10 network stack configuration 67
2 11 iscsi configuration 68
2 12 intel r x722 gigabit network connection 69
2 13 vlan configuration 71
2 14 driver health 73
3 chipset setup menu 74
3 1 processor configuration 75
3 2 common refcode configuration 77
3 3 upi configuration 78
3 4 memory configuration 80
3 5 iio configuration 82
3 6 advanced power management configuration 84
3 7 pch configuration 86
3 8 miscellaneous configuration 88
3 9 server me configuration 89
3 10 runtime error logging settings 90
3 11 power policy 92
4 server management menu 94
4 1 system event log 96
4 2 view fru information 97
4 3 bmc vlan configuration 98
4 4 bmc network configuration 99
4 5 ipv6 bmc network configuration 100
5 security menu 101
5 1 secure boot 102
6 boot menu 104
6 1 uefi usb drive bbs priorities 106
6 2 uefi network drive bbs priorities 107
6 3 uefi application boot priorities 108
7 save exit menu 109
8 1 ami standard pei 111
8 2 ami standard dxe 111
8 bios post codes 111
8 3 ami standard error 113
8 4 intel upi post codes 114
8 5 intel upi error codes 114
8 6 intel mrc post codes 115
8 7 intel mrc error codes 115
8 8 intel pm post codes 116
8 9 intel pm post codes 116
9 1 pei beep codes 117
9 2 dxe beep codes 117
9 bios post beep code ami standard 117

Gigabyte G241-G40 (rev. 100) [56/117] 2 2 redfish host interface settings

Содержание

Похожие устройства