Bosch GTS 10 J (0601B30500) [35/355] Checking and adjusting the basic adjustment
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Bosch GTS 10 J (0601B30500) [35/355] Checking and adjusting the basic adjustment

Bosch GTS 10 J (0601B30500) [35/355] Checking and adjusting the basic adjustment
English | 35
Bosch Power Tools 1 619 929 J53 | (12.5.11)
– Adjust the blade guard according to the workpiece height.
When sawing, the blade guard must always face lightly
against the workpiece.
– Switch on the machine.
– Saw through the workpiece applying uniform feed.
– Switch off the machine and wait until the saw blade has
come to a complete stop.
Sawing Bevel Angles
– Adjust the desired bevel angle. (see “Adjusting Bevel An-
gles”, page 33)
– Follow the worksteps in section “Sawing Straight Cuts” ac-
cordingly.
Sawing Mitre Angles (see figure S)
– Adjust the requested mitre angle (see “Adjusting Mitre An-
gles”, page 33)
– Place the workpiece against profile rail 28.
The profile may not be on the cutting line. If so, loosen
knurled nut 53 and move the profile.
– Raise or lower the saw blade with the crank 19 so that the
upper saw teeth project approx. 5 mm above the work-
piece surface.
– Adjust the blade guard according to the workpiece height.
When sawing, the blade guard must always face lightly
against the workpiece.
– Switch on the machine.
– With one hand, press the workpiece against the profile rail
and with the other hand, slowly move the angle stop via
locking knob 49 toward the front in guide groove 5.
– Switch off the machine and wait until the saw blade has
come to a complete stop.
Checking and Adjusting the Basic Adjustment
To ensure precise cuts, the basic adjustment of the machine
must be checked and adjusted as necessary after intensive
use.
A certain level of experience and appropriate specialty tools
are required for this.
A Bosch after-sales service station will handle this mainte-
nance task quickly and reliably.
Setting the Stops for Standard 0°/ 45° Bevel Angles
– Bring the power tool into the working position.
– Adjust to a 0° bevel angle.
– Tilt the protection guard 6.x toward the rear to the stop.
Checking: (see figure T1)
– Set an angle gauge to 90° and place it on the saw table 9.
The leg of the angle gauge must be flush with the saw blade 26
over the complete length.
Adjusting: (see figure T2)
– Loosen screw 54.
The 0° stop 55 can now be moved.
– Loosen locking lever 17.
– Move handwheel 18 toward the 0° stop until the leg of the
angle gauge is flush with the saw blade over the complete
length.
– Hold the handwheel in this position and tighten locking le-
ver 17 again.
–Tighten screw 54 again.
When the angle indicator 47 is not in line with the 0° mark of
scale 48, loosen screw 56 with a commercially available Phil-
lips screwdriver and align the angle indicator alongside the 0°
mark.
Repeat the above mentioned worksteps accordingly for the
45° bevel angle (loosening screw 57; moving the 45° stop
58). In this, the angle indicator 47 must not be misadjusted.
Parallelism of the Saw Blade to the Guide Grooves of the
Angle Stop (see figure U)
– Bring the power tool into the working position.
– Tilt the protection guard 6.x toward the rear to the stop.
Checking:
– With a pencil, mark the first visible saw tooth on the left
side that projects above the insert plate.
– Set an angle gauge to 90° and place it on the edge of the
guide groove 5.
– Move the leg of the angle gauge until it touches the marked
saw tooth, and read the clearance between saw blade and
guide groove.
– Turn the saw blade until the marked tooth projects above
the right side of the insert plate.
– Move the angle gauge alongside the guide groove to the
marked tooth.
– Measure the clearance between the saw blade and guide
groove again.
Both clearances measured must be identical.
Adjusting:
– Loosen Allen screws 59 at the front below the saw table
and Allen screws 60 at the rear below the saw table with
the supplied Allen key 21.
– Carefully move the saw blade until it is parallel to guide
groove 5.
–Retighten all screws 59 and 60 again.
Adjusting the Saw Table’s Clearance Indicator
(see figure V)
– Position the parallel guide on the right side of the saw
blade.
Move the parallel guide until the mark in the lens 27 indi-
cates 26 cm on the bottom scale.
To lock the parallel guide, press clamping handle 35 down
again.
– Loosen tensioning lever 15 and pull the table extension out
to the stop.
Checking:
On the upper scale 1, clearance indicator 51 must indicate
the identical value as the mark in lens 27 on the bottom scale
1.
Adjusting:
– Loosen screw 61 with a Phillips screwdriver and align
clearance indicator 51 alongside the 26 cm mark of the up-
per scale 1.
Adjusting the Lens of the Parallel Guide (see figure W)
– Bring the power tool into the working position.
– Tilt the protection guard 6.x toward the rear to the stop.
– Move parallel guide 10 from the right until it touches the
saw blade.
OBJ_BUCH-1325-002.book Page 35 Thursday, May 12, 2011 1:51 PM

Содержание

Похожие устройства

OBJ BUCH 1325 002 book Page 35 Thursday May 12 2011 1 51PM English 35 Adj us t the blade guard according to the workpiece height When the angle indicator 47 is not in line with the 0 mark of When sawing the blade guard must always face lightly scale48 loosen screw 56 with a commercially available Phil against theworkpiece Switch on the machine lips screwdriver and align theangle indicator alongside the 0 mark Saw through theworkpiece applying uniform feed Repeat the above mentioned worksteps accordingly for the Switch off the machine and wait until the saw blade has 45 bevel angle loosening screw 57 moving the45 stop come to a complete stop 58 In this theangleindicator47mustnotbe misadjusted Sawing Bevel Angles Parallelism Adjustthedesiredbevel angle see Adjusting Bevel An gles page 33 Angle Stop see figure U Follow the worksteps in section Sawing Straight Cuts ac cordingly Sawing Mitre Angles see figure S The profile may not be on the cutting line If so loosen Saw BladetotheGuideGroovesofthe Checking With a pencil mark the firstvisiblesaw tooth on the left side that projects above the insert plate Set an angle gauge to 90 and place it on the edge of the guide groove 5 Move the leg of the angle gauge until it touches the marked saw tooth and read the clearance between saw blade and knurled nut 53 and move the profile Raise or lower the saw blade with the crank 19 so that the upper saw teeth project approx 5 mm above the work the Bring the power tool into the working position Tilt the protection guard 6 x toward the rear to the stop Adjust the requested mitre angle see Adjusting Mitre An gles page 33 Place the workpiece against profile rail 28 of guide groove Turn the saw blade until the marked tooth projects above the right side of the insert plate piece surface Adj us t the blade guard according to the workpiece height Move the angle gauge al ongsi de the gui de groove to the When sawing the blade guard must always face lightly against theworkpiece marked tooth Measure the clearance between the saw blade and guide groove again Switch on the machine With one hand press the workpiece against the profile rail and with the other hand slowly move the angle stop via locking knob 49 toward the front in guide groove 5 Switch off the machine and wait until the saw blade has come to a complete stop Both clearances measured must be identical Adjusting Loosen Allen screws 59at the frontbelow thesaw table and Allen screws 60 at the rear below the saw table with the supplied Allen key 21 Checking and Adjusting the Basic Adjustment Carefully move the saw blade until it is parallel to guide To ensure predse cuts the basic adjustment of the machine grooves Retighten all screws 59 and 60 again must be checked and adjusted as necessary after intensive use A certain level of experience and appropriate specialty tools Adjusting the Saw Table s Clearance Indicator see figure V are required for this Position the parallel guide on the rightside of thesaw A Bosch after sales service station will handle this mainte blade nance task quickly and reliably Move the parallel guide until the mark in the lens 27 indi cates 26 cm on the bottom scale Sett ingtheStopsforStandardO 45 Bevel Angl es Bring the power tool into the working position Adj ust to a 0 bevel angl e To lock the parallel guide press clamping handle 35 down again Til t the protection guard 6 x toward the rear to the stop Loosen tensioning lever 15 and pull the table extension out to the stop Checking seefigureTl Checking Set an angle gauge to 90 and place it on the saw table 9 On the upper scale 1 clearance indicator 51 must indicate The leg of the angle gauge must be flush wi th thesaw blade26 the identical value as the mark in lens 27 on the bottom scale over the complete length 1 Adjusting see figure T2 Adjusting Loosen screw 54 Loosen screw 61 with a Phillips screwdriver and align The 0 stop 55 can now be moved Loosen locking lever 17 Movehandwheel 18towardthe0 stopuntilthelegofthe angle gauge is flush with the saw blade over the complete length Hold the handwheel in this position and tighten locking le ver 17 again Tighten screw 54 again Bosch Power Tools clearance indicator 51 a longs ide the 26 cm mark of theupper scale 1 Adju sting the Lens of th e Pa ra I lei G ui de see fi gu r e W Bring the power tool into the working position Tilt the protection guard 6 x toward the rear to the stop Move parallel guide 10 from the right until it touches the saw blade 1 619 929J53I 12 5 11

Скачать